Sharp Xv Z20000 Projector User Manual

-50
5  Insert the new lamp unit.
• Press the lamp unit fi rmly into the lamp 
unit compartment. Fasten the securing 
screws.
6  Attach the lamp unit cover.
• Close the lamp unit cover in the direc-
tion of the arrow. Then tighten the user 
service screws.
Info
• If the lamp unit and lamp unit cover are not 
correctly installed, the power will not turn on, 
even if the power cord is connected to the 
projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to...

Appendix
-51
Connecting Pin Assignments
RS-232C Terminal: 9-pin D-sub male connector
Pin No.  Signal  Name  I/O  Reference
1          Not connected
  2  RD  Receive Data  Input  Connected to internal circuit
  3  SD  Send Data  Output  Connected to internal circuit
  4    Reserved     Connected to internal circuit
  5  SG  Signal Ground    Connected to internal circuit
  6    Reserved    Connected to internal circuit
  7    Reserved    Connected to internal circuit
  8    Reserved     Connected to...

-52
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
Power On P O W R _ _ _ 1 OK or ERR OK
Power Off P O W R _ _ _ 0 OK or ERR OK or ERR
Lamp Status
TLPS___10:OFF,1:ON,2:Re-try
3:Waiting,4:Lamp Error0:OFF,4:Lamp Error
Projector Condition
TABN___10:Normal,
1:Temp High, 
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure0:Normal,
1:Temp High,
2:Fan Error,
4:Lamp Cover Open,
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure,...

-53
Appendix
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
INPUT Check
ICHK????1:COMPONENT1
2:COMPONENT2
3:S-VIDEO
4:VIDEO
5:DVI
6:HDMI1
7:HDMI2ERR
Freeze Off F R E Z _ _ _ 0 OK or ERR ERR
On F R E Z _ _ _ 1 OK or ERR ERR
Auto Sync Start A D J S _ _ _ 1 OK or ERR ERR
C1 INPUT RESIZE NORMAL R A S R _ _ _ 1 OK or ERR ERR
STRETCH R A S R _ _ _ 2 OK or ERR ERR
SIDE BAR/DOTBYDOT  R A S R _ _ _ 3 OK or ERR ERR
SMART STRETCH R A S R _ _ _ 4 OK or ERR ERR
CINEMA ZOOM...

-54
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
C1 INPUT Unveil Control Off R A U C _ _ _ 0 OK or ERR ERR
Level1 R A U C _ _ _ 1 OK or ERR ERR
Level2 R A U C _ _ _ 2 OK or ERR ERR
Level3 R A U C _ _ _ 3 OK or ERR ERR
Automatic Contrast Off R A A C _ _ _ 0 OK or ERR ERR
Level1 R A A C _ _ _ 1 OK or ERR ERR
Level2 R A A C _ _ _ 2 OK or ERR ERR
Level3 R A A C _ _ _ 3 OK or ERR ERR
Picture Reset R A R E _ _ _ 1 OK or ERR ERR
C2 INPUT Picture Mode Standard G M R...

-55
Appendix
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
VIDEO INPUT Picture Mode Standard V B P S _ _ _ 1 OK or ERR ERR
Natural V B P S _ _ _ 2 OK or ERR ERR
Dynamic V B P S _ _ _ 3 OK or ERR ERR
Movie1 V B P S _ _ _ 4 OK or ERR ERR
Movie2 V B P S _ _ _ 5 OK or ERR ERR
Memory V B P S _ _ _ 0 OK or ERR ERR
Contrast (–90 — +90) V B P I _ * * * OK or ERR ERR
Bright (–90 — +90) V B B R _ * * * OK or ERR ERR
Color (–30 — +30) V B C O _ * * * OK or ERR ERR
Tint...

-56
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
H1 INPUT Tint (–30 — +30) R D T I _ * * * OK or ERR ERR
Sharp (–30 — +30) R D S H _ * * * OK or ERR ERR
CLR Temp *
1R D C T * * * * OK or ERR ERR
BrilliantColorTMOff R D W E _ _ _ 0 OK or ERR ERR
On R D W E _ _ _ 1 OK or ERR ERR
Gamma Position Standard G M R D _ _ _ 0 OK or ERR ERR
Natural G M R D _ _ _ 1 OK or ERR ERR
Dynamic G M R D _ _ _ 2 OK or ERR ERR
Movie1 G M R D _ _ _ 3 OK or ERR ERR
Movie2 G M R D _ _...

-57
Appendix
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
C.M.S. M-Hue (–30 — +30) C M H M _ * * * OK or ERR ERR
C.M.S. Hue Reset C M R E _ _ _ 2 OK or ERR ERR
C.M.S. R-Saturation (–30 — +30) C M S R _ * * * OK or ERR ERR
C.M.S. Y-Saturation (–30 — +30) C M S Y _ * * * OK or ERR ERR
C.M.S. G-Saturation (–30 — +30) C M S G _ * * * OK or ERR ERR
C.M.S. C-Saturation (–30 — +30) C M S C _ * * * OK or ERR ERR
C.M.S. B-Saturation (–30 — +30) C M S B _ * * * OK or...

-58
CONTROL CONTENTS COMMAND PARAMETERRETURN
Power ONStandby mode
 (or 30-second startup time)
RS232C Port Off L N R S _ _ _ 0 OK or ERR ERR
On L N R S _ _ _ 1 OK or ERR ERR
Auto Power Off Off A P O W _ _ _ 0 OK or ERR ERR
On A P O W _ _ _ 1 OK or ERR ERR
Fan Mode Normal H L M D _ _ _ 0 OK or ERR ERR
High H L M D _ _ _ 1 OK or ERR ERR
PRJ Mode Front I M R E _ _ _ 0 OK or ERR ERR
Ceiling + Front I M R E _ _ _ 1 OK or ERR ERR
Rear I M I N _ _ _ 0 OK or ERR ERR
Rear + Front I M I N _ _ _ 1 OK or ERR ERR
All...

Appendix
-59
Specifi cations of wired remote control input 
•ø3.5 mm minijack
•External: GND
•Internal: +3.3V
Function and transmission codes
Wired remote control function code
LSB MSB
• System codes C1 to C5 are fi xed at “10110”.
• Codes C14 and C15 are reverse confi rmation bits, with “10” indicating “Front” and “01” indicating “Rear”.
Sharp remote control signal format
Transmission format: 15-bit format
Wave form of output signal: Output using pulse position modulation
•  t = 264 µs •  Pulse carrier...