Siemens SD-192/SD-192MX AND SD-232 Programming Manual

SET - 30
INSTALLATION MANUAL
TA-S30-1
Nov. 1, 1984 

.
.
SET-30 INSTAUAZION AND PROGRAMMING
The following informgtion is a SylnOpSiS df the installation and
programming proceduresoutlined in the SET-30 Documentation
Package.
It is intended to provide the craftsperson with a quick over-
view of the steps- which have to be taken to install and 
program
a SET-30.
For more detailed information,referto the Documentation
Package.
i.-.,”
-2- 

SET-30
SPECIFICATIONS
AUTOCOM
Number of Loops
PBX Loop Resistance
Loop TypePower Loop Resistance
Power Loop Distance
Voltage
Hold
Frequence Response
Tones
Keys
Display
Speakerphones
Handset
Data Retention
FCC Specification2 + Intercom
1200 Ohm maximum
Loop Start
120 Ohm maximum
2200 FT @ 24 GA
24 to 56 VDC
Non-polarity Sensitive
Hard hold on all lines
300 
-.3,400 Hz
;kandard 12 DTMF
32 5x7 matrix,alphanumeric character,
LCD technology
Integral
- Half Duplex
Standard K-type with modular connection
6...

FORM
Note:These items are supplied by Siemens-.a.?y----_-c------------------------_ ___-----------------________________o___--------------------------_____-------------------------------------
t ITEMNOMENCLATUREDESCRIPTION
QUANTITY I
I-----------------------------
-------------------------__--------------------------------------------------------------------------------__
I Programmable SET-30 Telephone 1
PN-X5051-Al001 (Exec. See lr 2# orPrivate) I
I-I
121Multiplexer 1
PN-X5051-Al.02
13iMultiplexer...

/---.
SET-30 can be programmed to operatein any ofthe .configurations
shown below:
1.2 dedicated line buttons stand-alone EXECUTIVE station.
2.2 dedicated line buttons plus intercom
station (with private or group secretary).button
EXECUTIVE
3.2 dedicated line buttons plusintercom button PRIVATE
SECRETARY station, (serving one EXECUTIVE station).
4.4 nondedicated line buttons plus intercom ‘button‘ GROUP
SECRETARY station, serving
UP to 32 EXECUTIVE stations or
nonexecutive stations (2500) phones).
5.5...

.
Power to the cage for the multiplexerand buffer cards is -48v and
/---..; ~ground from a separate power supply.
Total= 200 ma @ 48V X (number of multiplexer-“\:
cards +number ofmultiplexerand,.
buffer ports used)
Each multiplexer of buffer card is connectedvia a 
2%pair cable to
the MDF (female 
amphenol connector at cag.e end),
‘\
-6- 

SET-30 uses 4-pair wiring (using RI-45 connector)
.CUTIVE St-
.First pair (pin 4&S) T & R for 1st PBX 1~.Connected to PBX station
circuit.
Second pair (pins 3&6) Power (local or from buffer)
Third pair (pins 2&7) Dot used.Fourth pair (pins l&8) T & R for 2nd PRX 11~Connected to PBX station
circuit.Second line Gouldnormally not be used
in this configuration.
.auratlon wle SET-306Stand-alone 
Executive
IPBX
I :
I
-A-:IILine I Line: INTERII1 :2:con :,-’ IISET-30E
EXECUTIVE 

..
DNF: R~~CUTIVE/SX.EWARY COMBIWELQN
..ecutive Statran
First pair (pins 
4&S).T & R for 1st PBX laConnected
toPBXstationcircuitand
crossconnected to first pair -(pins
4&S) of secretary station.
Second pair (pins 
3&6)Power (local or from buffer)
Third pair (pins 
2&7)Uterca- crossconnected tothird
~t;~io~plns2&7) ofsecretary
Fourth pair (pins 
l&8).T & R ior 2nd PRX 1~(optional).
Connected toPBX stationcircuit.
Crossconnected to four‘th pair (pins
l&8) of secretary station,unless
it is a private line....

One Private Secretary Serving One Executive with Two Common
Lines and Dedicated IntercomPBX 
-
I
I
I
I
I
III
III II-
II I I
eILine ILine IInterI corn
III
f
lI
ISET-30EI---SET 30-E
III
PRIVATE SECRETARYEXECUTIVE
. .
-9- 

I OR II WIRING
Note:Different multiplexer cards are used for single and dual
secretary applications.-\.i:!/
Each PBX station circuit to appear at aSECRETARY station and
an 
EXECUTIVE station is wired to a line pair on the multiplexer
and the particular line on the 
EXECUTIVEinstrument where it is
to appear (pair 1 or 4 of the 
4-pair modular connector).
Each PBX station circuit to appear at a SECRETARY station and a
conventional telephone (2500 set) is alsowired to a line pair
on the multiplexerand the...