Singer Serger Professional 5 Manual

33
9
10
11
81
7
5
6
4
3
2 1
2 2
3) Threading the
(Brown)
Chain Stitch/Cover stitch Looper
20
While holding thread with fingers, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the tension
discs 3.
Thread the chain stitch/cover stitch looper as indicated
1~11.
Thread the top cover
thread guide by pulling
the thread towards the
left until it slips under
guide. Then pull thread
along the right side of
button as illustrated. Pass thread from back to...

92
7 5
8
6
43
1
10 11
8
7
9
6
4
5
C
A
BD
21
Thread the right needle as indicated 1~9.Turn the hand wheel toward you until the chain stitch
looper extends out 10mm from the needle plate
edge.
Thread the looper area of the machine following
the brown color-coded thread guides 4~11.
Place the thread with the point of the tweezers
through threading guide 4.
Place the thread with the point of the tweezers
through the front slot of threading guide 5.
Thread the looper eye (A) from front to back.
Pull about...

95
8 6
7
4
3
3
2
2
1
22
Pass thread from back to the front through the
thread guide 1.
While holding thread with finger, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3.
Continue to thread points 4~8.
Note: Slip thread into the rear slot on the thread guide 5 and the slot of take-up lever cover 6.
Then slip thread into the right slot on the thread guide 7, and into the right slot on the thread
guide 8.
Before threading eye of...

3
2 1
9
7
8 5
6
2
4
1
29
5) Threading the
(Orange)
Chain Stitch Needle
(D on needle clamp)
23
Thread the eye of the right needle 9.
Note: Use of tweezers in the accessory case willmake needle eye threading easy.
The position of the thread must be behind the thread
guide.
Draw about 10cm(4 inches) of thread through
needle eye towards the rear of machine.
Place the thread to the back, under the presser
foot.
Thread the top cover
Thread guide by pulling
the thread towards the
left until it slips under...

4
9
9
8
7
6
5
3
3
24
While holding thread with fingers, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3.
Thread the eye of the left needle 9.
Note: Use of tweezers in the accessory case will make needle eye threading easy.
The position of the thread must be behind the
the thread guide.
Draw about 10cm (4 inches) of thread through
needle eye to hang free.
Place the thread to the back, under the presser
foot. Continue to thread...

32
3
2
7
1 9
8
5
6
1
43
2
(1) Threading the
Cover Stitch Left Needle
25
While holding thread with finger, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3. Thread the top cover
thread guide by pulling
the thread towards the
left until it slips under
guide. Then pull thread
along the right side of
button as illustrated. Thread the cover stitch left / chain stitch needle as
indicated 1~9.
Pass thread from back to the front through...

4
5
8
9 7
6 3
2 9
1
8
9
7
6
45
(2) Threading the Cover Stitch Middle / Chain Stitch
26
Needle(Blue) (D on needle clamp)
Thread the cover stitch middle / chain stitch
needle as indicated 1~9. Continue to thread points 4~8.
Note: Slide thread into front slot on thread guide 5 and slot of take-up lever
cover 6. Then slip thread into left slots
of thread guides 7 and 8.
Thread the eye of the left needle 9.
Note: Use of tweezers in the accessory case will make needle eye threading easy.
Draw about 10cm (4...

9
8
6
7
3
4
5
3
2
2
1
27
While holding thread with fingers, pass it between
the tension discs and pull thread down to make
certain it is properly located in between the
tension discs 3.
Continue to thread points 4~8.
Pass thread from back to the front through the
thread guide 1.
Thread the top cover
thread guide by pulling
the thread towards the left
until it slips under guide.
Then pull thread along the
right side of button as
illustrated.
Before threading eye of needle, make sure thread is
in front of...

221
9
6
7
8 5
43
2
1 9
(3) Threading the
Cover Stitch Right Needle
(Green) (E on needle clamp)
28
Thread the cover stitch right needle as indicated
1-9.
Pass thread from back to the front through the
thread guide 1.
Thread the top cover
thread guide by pulling
the thread towards the
left until it slips under
guide. Then pull thread
along the right side of
button as illustrated. Thread the eye of the middle needle 9.
Note: Use of tweezers in the accessory case will make needle eye threading easy.
Draw...

9
8
9 4
5
7
6
3
3
29
Continue to thread points 4~8.
Note: Slip thread into the rear slot on thread
guides 5. Slip the thread into the slot
of the Take-up Lever Cover 6. Slip the thread
into the right slots for thread guides 7 and 8.
Before threading eye of needle, make sure thread is
in front of thread guide located on the bottom of the
needle clamp for Cover stitch.
Thread the eye of the right needle 9.
Note: Use of tweezers in the accessory case will make needle eye threading easy.
Draw about 10cm (4...