Sony Bdv E300 Operating Instructions

							External Audio Device
61US
6Press X/x repeatedly until “START” 
appears in the front panel display, then 
press .
The unit starts pairing and “SEARCH” 
flashes in the front panel display.
To cancel pairing, press SYSTEM MENU.
7Start pairing of the S-AIR sub unit.
xFor the surround amplifier
Press POWER on the surround amplifier to 
turn on the surround amplifier and press 
PAIRING on the rear panel of the surround 
amplifier.
The PAIRING indicator of the surround 
amplifier flashes red when pairing starts.
When sound transmission is established, 
the PAIRING indicator of the surround 
amplifier turns red and “PAIRING” and 
“COMPLETE” appear alternately in the 
front panel display.
Tip To press PAIRING on the rear panel of the 
surround amplifier, a slim instrument, such as a 
paper clip, can be used.
xFor the S-AIR receiver
Refer to the operating instructions of the 
S-AIR receiver.
When sound transmission is established, 
“PAIRING” and “COMPLETE” appear 
alternately in the front panel display.
Note Perform pairing within several minutes of Step 
5. If you do not, “PAIRING” and 
“INCOMPLETE” appear alternately in the front 
panel display. To continue pairing, press   and 
start again from Step 5. To cancel pairing, press 
SYSTEM MENU.
8Press SYSTEM MENU.
The system menu turns off.
Note When you perform pairing, “(PAIRING)” appears 
beside ID on the display for selecting ID.
To cancel pairing
Change the ID setting of the unit by using the 
S-AIR ID switch of the unit. If you select a new 
ID, pairing is canceled.You can check the S-AIR status such as the 
S-AIR ID or pairing information.
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “S-AIR ID” 
appears in the front panel display, then 
press  or c.
The S-AIR ID of the unit appears in the 
front panel display. When the unit is paired, 
“(PAIRING)” appears beside ID.
4Press SYSTEM MENU.
The system menu turns off.
If you use multiple wireless systems which share 
the 2.4 GHz band, such as wireless LAN or 
Bluetooth, the transmission of S-AIR products 
or other wireless systems may be unstable. In 
this case, the transmission may be improved by 
changing the following “RF CHANGE” setting.
1Press SYSTEM MENU.
2Press X/x repeatedly until “S-AIR 
MENU” appears in the front panel 
display, then press   or c.
3Press X/x repeatedly until “RF 
CHANGE” appears in the front panel 
display, then press   or c.
Note When the wireless transmitter is not inserted in 
the unit, “RF CHANGE” cannot be selected.
Checking the S-AIR status of 
the unit
If sound transmission is 
unstable
For the surround amplifier
For the S-AIR receiver
 
						

							62US
4Press X/x to select the desired setting.
 “AUTO”: Normally select this. The 
system changes “RF CHANGE” to “ON” 
or “OFF” automatically.
 “ON”: The system transmits sound by 
searching for a better channel for 
transmitting.
 “OFF”: The system transmits sound by 
fixing the channel for transmitting.
5Press .
The setting is made.
6Press SYSTEM MENU.
The system menu turns off.
7When you set “RF CHANGE” to “OFF,” 
select the ID so that sound 
transmission is most stable (page 57).
Note In most cases, you will not need to change this 
setting.
– If “RF CHANGE” is set to “OFF,” transmission 
between the unit and S-AIR sub unit can be 
performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE 
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE 
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE 
802.11b/g channel 11
 The transmission may be improved by changing the 
transmission channel (frequency) of the other 
wireless system(s). For details, refer to the operating 
instructions of the other wireless system(s).
 
						

							Other Operations
63US
Using the Control for 
HDMI Function for 
“BRAVIA” Sync
This function is available on TVs with the 
“BRAVIA” Sync function only.
By connecting Sony components that are 
compatible with the Control for HDMI function 
with an HDMI cable, operation is simplified as 
below:
– Theater Mode (page 64)
– One-Touch Play (page 64)
– System Power Off (page 64)
– Volume Limit (page 65)
– System Audio Control (page 65)
– Language Follow (page 65)
Control for HDMI is a mutual control function 
standard used by CEC (Consumer Electronics 
Control) for HDMI (High-Definition 
Multimedia Interface).
The Control for HDMI function will not work in 
the following cases:
– When you connect this system to a 
component which is not compatible with the 
Control for HDMI function.
– A component does not have an HDMI jack.
There are convenient buttons on the system’s 
remote for operating the TV, such as 
THEATER, ONE-TOUCH PLAY, and TV "/1. 
For details, see “Controlling Your TV with the 
Supplied Remote” (page 69) and refer to the 
operating instructions of the TV.
Note Depending on the connected component, the Control 
for HDMI function may not work. Refer to the 
operating instructions supplied with the component.
 The Control for HDMI function may not work if you 
connect a component other than Sony, even if the 
component is compatible with the Control for HDMI 
function.
(Control for HDMI - Easy Setting)
The system is compatible with the Control for 
HDMI - Easy Setting function. If the TV is 
compatible with the Control for HDMI - Easy 
Setting function, you can set the system’s 
[Control for HDMI] function automatically by 
setting the TV. For details, refer to the operating 
instructions of the TV.
If the TV is not compatible with the Control for 
HDMI - Easy Setting function, set the Control 
for HDMI function of the system and TV 
manually.
Note For details on setting the TV, refer to the operating 
instructions.
1Make sure that the system and the TV 
are connected with an HDMI cable.
2Turn on the TV and press [/1 to turn on 
the system.
3Switch the input selector on your TV so 
that the signal from the system through 
the HDMI input appears on the TV 
screen.
4Set the Control for HDMI function of the 
system and TV.
The Control for HDMI function for system 
and TV is simultaneously set to on.
Other Operations
THEATER
NIGHT S-AIR
MODEDYNAMICBASS
TV
TVONE-TOUCH
PLAY
BRAVIA  Sync
Preparing for the Control for 
HDMI function
 
						

							64US
To set the [Control for HDMI] 
function of the system to on/off 
manually
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [HDMI Settings], 
then press  .
The options for [HDMI Settings] appear.
4Press X/x to select [Control for HDMI], 
then press  .
5Press X/x to select the setting, then 
press .
: On.
 [Off]: Off.
Note During the setting of the Control for HDMI function 
for the system, the System Audio Control function 
does not work.
Tip The default setting of the Control for HDMI function 
of the system is [On].
(Theater Mode)
If your TV is compatible with the Theater mode, 
when you press THEATER, you can enjoy the 
optimum video mode and sound quality suited 
for movies, and TV sound is output from the 
system’s speakers automatically. Also, the TV’s 
video mode switches to Theater Mode.(One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV 
turns on, the TV is set for BD/DVD input 
selector, and the system starts playing a disc 
automatically.
Also, when you insert a disc, One-Touch Play is 
enabled. If One-Touch Play does not start (in the 
case of inserting a disc that is not compatible 
with the auto playback function), press N or 
ONE-TOUCH PLAY.
The system and TV work as follows (e.g.):
(System Power Off)
When you turn the TV off by using the POWER 
button on the TV’s remote or TV "/1 on the 
system’s remote, the system turns off 
automatically.
Note Before using the System Power Off function, set the 
function for TV power. For details, refer to the 
operating instructions of the TV.
 Depending on the status, the system or the connected 
components may not turn off automatically. For 
details, see the operating instructions supplied with 
the connected components.
Using the Theater Mode
Watching BD/DVD by a single 
button press
This system TV
Turns on. (If not already 
turned on.)
r
Switches to “BD/DVD” 
function.
r
Starts playing the disc and 
outputs the sound.Turns on. (If not already 
turned on.)
r
Switches to HDMI input.
r
Minimizes sound level.
(System Audio Control)
Turning the system off in sync 
with the TV
 
						

							Other Operations
65US
(System Audio Control)
You can enjoy TV sound in this system by easy 
operation.
To use this function, connect the system and the 
TV with an audio cord and an HDMI cable 
(page 21).
You can use the System Audio Control function 
as follows:
 You can enjoy TV sound from the speakers of 
the system by means of a simple operation. For 
details, see the operating instructions of the 
TV.
 When the system is turned on, TV sound will 
be output from the speakers of the system.
 When TV sound is output from the speakers of 
the system, you can adjust the volume and turn 
off the sound of the system using the TV 
remote.
Note While the TV is in PAP (picture and picture) mode, 
the System Audio Control function will not work. 
When the TV exits PAP mode, the output method of 
the TV returns to the one before PAP mode.
(Volume Limit)
If you change the output method of the TV to the 
system speaker on the TV menu or by pressing 
THEATER, loud sound may be output 
depending on the volume level of the system. 
You can prevent this by limiting the maximum 
level of the volume. For details, see [Volume 
Limit] (page 82).(Language Follow)
When you change the language for the on-screen 
display of the TV, the system’s on-screen 
display language is also changed after turning 
the system off and on.
Enjoying TV sound from the 
speakers in this system
Setting the Maximum Volume 
Level of the System
Changing the language for the 
on-screen display of the TV
 
						

							66US
Calibrating the 
Appropriate Settings 
Automatically
[Auto Calibration]
D. C. A. C. (Digital Cinema Auto Calibration) 
can set the appropriate surround sound 
automatically.
Note The system outputs a loud test sound when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and neighbors.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Auto Calibration], 
then press  .
The confirmation display for [Auto 
Calibration] appears.
5Connect the calibration mic to the 
A.CAL MIC jack on the rear panel.
Set up the calibration mic at ear level using 
a tripod, etc. (not supplied). The front of 
each speaker should face the calibration 
mic, and there should be no obstruction 
between the speakers and the calibration 
mic.
6Press X/x to select [Start].
To cancel, select [Cancel].
7Press .
[Auto Calibration] starts.
The system adjusts the speaker settings 
automatically.
Be quiet during the measurement.
Note Before [Auto Calibration], make sure that the 
surround amplifier turns on and you install the 
surround amplifier in the appropriate location. If 
you install the surround amplifier in an improper 
location, such as another room, proper 
measurement will not be obtained.
 When you use the Wireless Surround Speaker 
Kit (WAHT-SBP1, optional) for the surround 
back speakers (page 17), install the speakers in 
appropriate location and turn the surround 
amplifier on.
 Loud test sound is output when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and 
neighbors.
EZW-T100
A
N
T
E
N
N
A
AUD
IO
D
IG
IT
A
L
 INA
U
DI
O
 I
NA
U
DIO
 I
N
A. CAL MICE
C
M
-A
C
2
F
M
A
MC
O
A
X
I
A
L7
5
COAXIALOPTICAL
R L
R LEX
TTV
TVD
IG
IT
A
L
 INS
A
T
/C
AB
L
EDC5V500mA  MAX
Calibration mic
 
						

							Other Operations
67US
8Confirm the conclusions of [Auto 
Calibration].
The conclusions appear on the TV screen. 
Press C/c to change the page. The first page 
shows the distance of speakers. The second 
page shows the level of speakers.
Note If measurement fails, follow the message then 
retry [Auto Calibration].
Tip You can change a measurement unit (feet or 
meters) by pressing the color button (RED).
9Press X/x to select [OK] or [Cancel], 
then press  .
xThe measurement is OK.
Disconnect the calibration mic, then select 
[OK]. The result is implemented.
xThe measurement is not OK.
Follow the message, then select [OK] to 
retry.
Note While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
– do not insert or eject a disc.
– do not connect the headphones to the surround 
amplifier.
– do not disconnect the calibration mic.
Setting the Speakers
[Speaker Settings]
To obtain the best possible surround sound, set 
connection of the speakers and their distance 
from your listening position. Then use the test 
tone to adjust the level and the balance of the 
speakers to the same level.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Speaker Settings], 
then press  .
The [Speaker Settings] display appears.
5Press X/x to select the item, press  .
Setup the following settings.
x[Connection]
If you do not connect center or surround 
speakers, set the parameters for [Center] and 
[Surround]. Since the front speaker and 
subwoofer settings are fixed, you cannot change 
them.
When you use the Wireless Surround Speaker 
Kit (WAHT-SBP1, optional) for the surround 
back speakers (page 17), set [Surround Back] 
also.
[Front]
[Yes]
[Center]
[Yes]: Normally select this.
[None]: Select this if no center speaker is used. 
[Surround]
[Yes]: Normally select this.
[None]: Select this if no surround speaker is 
used.
[Surround Back]
[Yes]: Select this if surround back speakers are 
used.
[None]
: Select this if no surround back speaker 
is used.
 
						

							68US
[Subwoofer]
[Yes]
x[Distance]
When you move the speakers, be sure to set the 
parameters of the distance (A) from the 
listening position to the speakers.
You can set the parameters from 0 to 23 feet (0.0 
to 7.0 meters).
The speakers in the illustration correspond to the 
following:
1Center speaker
2Front left speaker (L)
3Front right speaker (R)
4Subwoofer
5Surround left speaker (L)
6Surround right speaker (R)
7Surround back left speaker (L) (optional)
8Surround back right speaker (R) (optional)
[Front Left/Right] 10 ft/3.0 m: Set the front 
speaker distance.
[Center]* 10 ft/3.0 m
: Set the center speaker 
distance.
[Surround Left/Right]* 10 ft/3.0 m
: Set the 
surround speaker distance.
[Surround Back Left/Right]* 10 ft/3.0 m
: Set the 
surround back speaker distance.
[Subwoofer] 10 ft/3.0 m
: Set the subwoofer 
distance.
* This item appears when you set to [Yes] in the 
[Connection] setting.
Note Depending on the input stream, [Distance] may not 
be effective.
Tip You can change a measurement unit (feet or meters) 
by pressing the color button (RED).
x[Level]
You can adjust the sound level of the speakers. 
You can set the parameters from –6.0 dB to +6.0 
dB. Be sure to set [Test Tone] to [On] for easy 
adjustment.
[Front Left/Right] 0.0 dB
: Set the front speaker 
level.
[Center]* 0.0 dB
: Set the center speaker level.
[Surround Left/Right]
* 0.0 dB: Set the surround 
speaker level.
[Surround Back Left/Right]
* 0.0 dB: Set the 
surround back speaker level.
[Subwoofer] 0.0 dB
: Set the subwoofer level.* This item appears when you set to [Yes] in the 
[Connection] setting.
x[Test Tone]
The speakers will emit a test tone to adjust 
[Level].
[Off]
: The test tone is not emitted from the 
speakers.
[On]: The test tone is emitted from each speaker 
in sequence while adjusting level. When you 
select one of the [Speaker Settings] items, the 
test tone is emitted from each speaker in 
sequence.
Adjust the sound level as follows.
1Set [Test Tone] to [On].
2Press X/x to select [Level], then press 
.
3Press X/x to select the desired speaker 
type, then press  .
4Press C/c to select the left or right 
speaker, then press X/x to adjust the 
level.
5Press .
6Repeat Steps 3 to 5.
7Press RETURN.
The system returns to the previous display.
8Press X/x to select [Test Tone], then 
press .
A
A
2
5
786 1
43
 
						

							Other Operations
69US
9Press X/x to select [Off], then press 
.
Note The test tone signals are not output from the HDMI 
OUT jack.
Tip To adjust the volume of all the speakers at one time, 
press VOLUME +/–.
Controlling Your TV with 
the Supplied Remote
By adjusting the remote signal, you can control 
your TV with the supplied remote.
Note When you replace the batteries of the remote, the 
code number may reset itself to the default (SONY) 
setting. Reset the appropriate code number.
Press and hold TV [/1 while entering your 
TV’s manufacturer’s code (see the table) 
using the number buttons. Then release TV 
[/1.
If you successfully set the manufacturer’s code, 
the TV button flashes twice slowly. If the setting 
is unsuccessful, the TV button flashes five times 
quickly.
Code numbers of controllable TVs
If more than one code number is listed, try 
entering them one at a time until you find the 
code that works with your TV.
Preparing the remote for 
controlling the TV
Manufacturer Code number
SONY 501 (default), 502
DAEWOO 506
EMERSON 567
FUNAI 548
GE 509
GOLDSTAR/LG 503, 517, 544, 568
GRUNDIG 533
HITACHI 514
ITT 521, 522
JVC 516
LOEWE 518
MITSUBISHI/MGA 527
NEC 503
NOKIA 521, 522, 573, 575
PANASONIC 553, 572
PHILIPS 515, 518, 557, 570
PIONEER 526
 
						

							70US
You can control the TV using the following 
buttons. To use these buttons (other than 
THEATER, TV [/1, TV INPUT), set the 
remote to the TV mode by pressing TV, so that 
TV lights up for 1 second.
To exit the TV mode, press TV so that TV 
flashes four times.
Note While in the TV mode, if you press any of the 
following buttons, TV lights up. (Depending on the 
manufacturer setting, some buttons may not work, 
and TV does not light up.)
 When you press other than the following buttons 
while the remote is in the TV mode, TV flashes four 
times and the remote exits the TV mode 
automatically, and the system is operated as the 
function of the pressed button.
 Depending on the TV, you may not be able to use 
some or all of the buttons.
Tip The function of these buttons are same as the remote 
buttons of the SONY TV. For details, refer to the 
operating instructions of the TV. RADIO SHACK 565
RCA/PROSCAN 510
SABA 530, 537, 558
SAMSUNG 515, 517, 544, 566, 569, 571, 
574
SANYO 508, 545
SHARP 535, 565
TELEFUNKEN 547, 558
THOMSON 547, 549
TOSHIBA 541, 551
ZENITH 543
Controlling the TV with the 
remote
By pressing You can
TV "/1Turn the TV on or off.
THEATER Enjoy optimal images and sound 
suited for movies.
TV INPUT Switch the TV’s input source 
between the TV and other input 
sources.
VOLUME +/– Adjust the TV volume.
CH +/– Select the TV channel.
MUTING Turn off the TV sound 
temporarily.
Manufacturer Code number
Number buttons, 
, ENTERSelect the TV channel.
HOME Display the menu of the TV.
FAVORITES Display the favorite channel list.
CC Display closed captioning.
GUIDE Display the Digital Electronic 
Programme Guide (EPG).
TOOLS Display the operation menu for the 
current display.
RETURN Return to the previous channel or 
layer on the menu of the TV.
Input “.” (dot) when inputting 
numerics.
WIDE Change the aspect ratio of the 
connected TV.
C/X/x/c, Select the item on the menu.
DISPLAY Display the information.
By pressing You can