Stihl 441 Cm Manual

MS 441 C-M
English
49 aRequired distance between depth 
gauge and cutting edge
When cutting softwood outside of the 
frost season, the distance can be 
increased by up to 0.2 mm (0.008").
Lowering the depth gauges
The depth gauge setting is lowered 
when the cutter is sharpened.
NCheck the depth gauge setting after 
each sharpening
NLay the appropriate file gauge (1) 
for the chain pitch on the saw chain 
and press it against the cutter to be 
checked – if the depth gauge 
protrudes past the file...

MS 441 C-M
English
50 Sharpening tools (special accessories)
Chain pitch Round file ^Round file File holder File gaugeTaper square file Sharpening set 
1)
Inches (mm) mm (Inches) Part number Part number Part number Part number Part number
1/4 P (6.35) 3.2 (1/8) 5605 771 32065605 750 4300 0000 893 4005 0814 252 3356 5605 007 1000
1/4 (6.35) 4.0 (5/32) 5605 772 40065605 750 4327 1110 893 4000 0814 252 3356 5605 007 1027
3/8 P (9.32) 4.0 (5/32) 5605 772 4006 5605 750 4327 1110 893 4000 0814 252 3356 5605...

MS 441 C-M
English
51
Maintenance and Care
The following information applies in normal operating conditions. The specified inter-
vals must be shortened accordingly when working for longer than normal or under 
difficult cutting conditions (extensive dust, highly resinous lumber, lumber from trop-
ical trees, etc.). If the machine is only used occasionally, the intervals can be 
extended accordingly.
Before starting work
At the end of work and/or 
daily
Whenever tank is refilled
Weekly
Monthly
Yearly
If...

MS 441 C-M
English
52
Air filterCleanXX
ReplaceX
Anti-vibration elementsCheckXX
Have them replaced by a servicing 
dealer
1)X
Air intake on fan housing CleanXX X
Cylinder fins CleanXX X
CarburetorCheck idle adjustment – saw chain must 
not rotateXX
If the saw chain rotates in idle, have the 
chain saw serviced by a servicing 
dealer
1)X
Spark plugAdjust electrode gapX
Replace after 100 hours of operationX
Accessible screws, nuts and bolts Tighten
2)X
Spark arresting screen in mufflerHave checked by a...

MS 441 C-M
English
53 1Carburetor Box Cover with Clips
2Handle Heating Switch (Depending 
on Model)
3Spark Plug Boot
4Shutter (Summer and Winter 
Operation)
5Decompression Valve 
(Automatically Resetting)
6Chain Brake
7Chain Sprocket
8Chain Sprocket Cover
9Chain Catcher
10Chain Tensioner
11Bumper Spike
12Guide Bar
13Oilomatic Saw Chain
14Oil Filler Cap
15Muffler (with Spark Arresting 
Screen, not Fitted on all Markets)
16Front Hand Guard
17Front Handle (Handlebar)
18Starter Grip
19Fuel Filler Cap...

MS 441 C-M
English
54
Definitions
1 Carburetor Box Cover with Clips
Lock for carburetor box cover.
2 Handle Heating Switch (Depending 
on Model)
For switching the electric handle 
heating on and off.
3 Spark Plug Boot
Connects the spark plug with the 
ignition lead.
4 Shutter (Summer and Winter 
Operation)
With summer and winter positions. 
Winter position provides warm 
intake air for cold weather 
operation.
5 Decompression Valve –
(Automatically resetting)
Releases compression pressure to 
make...

MS 441 C-M
English
55
EPA / CEPA
The Emission Compliance Period 
referred to on the Emissions 
Compliance Label indicates the number 
of operating hours for which the engine 
has been shown to meet Federal 
emission requirements.
Category
Engine
STIHL single cylinder two-stroke engine
Ignition system
Electronic magneto ignition 
(breakerless)
Fuel system
All position diaphragm carburetor with 
integral fuel pump
Chain lubrication
Fully automatic, speed-controlled oil 
pump with reciprocating piston –...

MS 441 C-M
English
56 Please enter your saw model, serial 
number as well as the part numbers of 
the guide bar and saw chain in the 
spaces provided. This will make re-
ordering simpler.
The guide bar and saw chain are subject 
to normal wear and tear. When 
purchasing these parts, always quote 
the saw model, the part numbers and 
names of the parts.
See "Specifications" in this manual for 
the recommended reduced kickback 
cutting attachments.Users of this unit should carry out only 
the...

MS 441 C-M
English
57 STIHL Incorporated Limited Warranty 
Policy
This product is sold subject to the STIHL 
Incorporated Limited Warranty Policy, 
available at 
http://www.stihlusa.com/warranty.html.
It can also be obtained from your 
authorized STIHL dealer or by calling 
1-800-GO-STIHL (1-800-467-8445).Your Warranty Rights and Obligations
The U.S. Environmental Protection 
Agency (EPA) and STIHL Incorporated 
are pleased to explain the Emission 
Control System Warranty on your 
equipment type engine....

MS 441 C-M
English
58 problem exists. The warranty repairs will 
be completed in a reasonable amount of 
time, not to exceed 30 days.
If you have any questions regarding your 
warranty rights and responsibilities, 
please contact a STIHL customer 
service representative at 1-800-467-
8445 or you can write to
STIHL Inc.,
536 Viking Drive, P.O. Box 2015,
Virginia Beach, VA 23450-2015
www.stihlusa.com
Coverage by STIHL Incorporated
STIHL Incorporated warrants to the 
ultimate purchaser and each 
subsequent...