Studio Experience Projector Premier 30hd User Manual

							Easy to Use Functions
49
Deinterlace
This function allows you to determine the type of incoming video content-film, static interlaced video and 
moving interlaced video. Different algorithms are applied for each of the content types.
Select “Deinterlace” from the 
“Options” menu on the menu screen.
For operating the menu screen, see 
page 31.
 Note
•  In PAL50Hz or SECAM, the 2:2 pull down 
enhancement will be enabled only in film 
mode, after the film source has been 
entered.
Selected itemDescription
DCTI
This function is useful to 
enhance video by replacing 
the edges of the video with 
edges that have steeper rise 
and fall times. DCTI turns 
sloped or sinusoidal 
waveforms into rectangular 
or square waveforms with 
the same duty cycles and 
peak-to-peak amplitude. Its 
useful for 4:1:1 video 
sources. The range is from 
0 to 7.
Video on film 
(VOF)
This function is used to 
identify video artifacts while 
in film mode. VOF attempts 
to repair the artifacts using 
the low-angle interpolator 
while remaining in film 
mode.
Film Mode
Reproduces the image of 
the film source clearly. 
Displays the optimized 
image of film transformed 
with 3:2 pull down (NTSC 
and PAL60Hz)or 2:2 pull 
down (PAL 50Hz and 
SECAM) enhancement to 
progressive mode images.
Main Menu 
						

							50
Easy to Use Functions
Reset
Select this option to set all items in the “Option” 
menu to the factory default values.
Lamp Timer Reset
Lamp Timer Reset is used to reset the lamp 
counter.
You should reset the Timer after you install a 
new lamp. The cumulative lamp usage time is 
shown in the Status Screen.
Main Menu
Main Menu 
						

							Easy to Use Functions
51
Status Screen
The Status screen displays information about the current input signal.
Factory reset
The Logo will be shown for about 20 seconds, 
then the projector will be reset. 
 Note
•  The Logo will be shown about 20 seconds, 
and then the projector will be reset.
Main Menu
Screen display during Factory Reset
Main Menu 
						

							52
Easy to Use Functions
NOTES 
						

							Appendix
53
Appendix 
						

							54
Appendix
Maintenance
Cleaning the projector
„Unplug the power cord before cleaning the projector.
„Avoid using benzene or thinner, as these can damage the finish on the cabinet and operation panel.
„Do not use volatile agents such as insecticides on the projector.
„Do not leave rubber or plastic objects in contact with the projector for long periods as they may damage 
the finish of the projector.
„Wipe off dirt gently with a soft flannel cloth.
„For hard-to-remove dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then 
wipe the projector.
Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test 
on a small, inconspicuous area on the projector before using.
Cleaning the lens
„Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning 
the lens. Do not use any liquid cleaning agents, as they may wear off the coating film on the surface of the 
lens.
„The surface of the lens is easily damaged, do not to scrape or hit the lens.
Cleaning the exhaust and intake vents
„Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Neutral detergent 
diluted with water
N
e
ut
ral
 d
e
te
rge
nt
Cleaning 
Paper 
						

							Appendix
55
Cleaning the Ventilative Holes
•  This projector is equipped with ventilative 
holes to ensure the optimal operating 
condition of the projector.
•  Periodically clean the ventilative hole by 
vacuuming it off with a vacuum cleaner.
•  The ventilative holes should be cleaned 
every 100 hours of use. Clean the 
ventilative holes more often when the 
projector is used in a dirty or smoky 
location.
Cleaning the 
Ventilative Holes
1Turn off the power and 
disconnect the power cord.
Press  on the projector or  on 
the remote control to turn off the power. 
Wait until the cooling fan stops.
2Unplug the Power Cord.
3Clean the dust off by placing the 
cleaner hose on the intake and 
exhaust ventilative holes.
STATUSEXIT
INPUTMENU
ECO
ENTER
COMPONENT 1
COMPONENT 2
Side and Rear view
Ventilative holes
Bottom view
Ventilative holes
Power button
mp chassis cover while replacing the lamp.xt to them until they have sufficiently cooled down.
nvironment.Made in Taiwan
Pr/Cr Pb/CbYPCDVI 
						

							56
Appendix
About the Lamp
The projector lamp has a life of 2000 hours. Maintain proper ventilation to keep the lamp operating 
throughout its lifetime. Do not subject the projector to unnecessary vibration to ensure that the 
lamp does not break.
„It is recommended that the lamp (sold separately) be replaced after approximately 2,000 cumulative hours 
of use or when you notice a significant deterioration in the picture and color quality. The number of hours 
the lamp has been used can be checked with “Lamp Timer” in the “Options” menu on the menu screen.
„For lamp replacement, please consult your nearest Authorized Service Center or Dealer.
„The actual lamp service life may be less than 2000 hours depending on the environment in which the 
projector is used.
Caution Concer ning the Lamp
„This projector uses a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure is 
caused by excessive shock, improper cooling, surface scratches or deterioration of the lamp due to usage. 
The period of time up to failure largely varies depending on the individual lamp and/or the condition and 
the frequency of use. It is important to note that failure can often result in the bulb cracking.
„When the lamp replacement indicator and on-screen display icon are illuminated or are flashing, it is 
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be 
operating normally.
„If the lamp breaks glass particles may spread inside the lamp cage or gas contained in the lamp may be 
vented into the room from the exhaust vent. As the gas in this lamp contains mercury, ventilate the room 
well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult 
with a doctor as soon as possible.
„If the lamp breaks, there is also a possibility that glass particles may spread inside the projector.
If this happens, it is recommended you contact your nearest Authorized Dealer to remove the damaged 
lamp and assure safe operation.
Replacing the Lamp
CAUTION!  Do not remove the lamp unit immediately after operation of the projector. The 
lamp will be hot and touching it can lead to burn or injury. Wait at least one hour after the 
power cord is disconnected to allow the surface of the lamp unit to fully cool before removing 
the lamp unit. 
						

							Appendix
57
Removing and Installing the Lamp Unit
Follow these instructions to replace the lamp.
•  Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or 
the inside of the projector.
•  To avoid injuring yourself and damage to the lamp, be sure to carefully follow the steps below.
•  Do not loosen other screws except for the lamp unit cover and lamp unit. 
(Only the silver screws are loosened).
1. If the projector is running, press  on the projector or  on the remote control to 
turn off the power. Wait until the cooling fan stops.
 Warning!
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn 
or injury.
2. Disconnect the power cord and wait at least an hour for the lamp to cool.
3. Remove the lamp unit cover.
•  Loosen the user service screw that secures the lamp unit cover. Then open the cover in the direction of the 
arrow.
COMPONENT 1
COMPONENT 2
STATUSEXIT
INPUTMENU
ECO
ENTER
 M4* 8.9 screws 
						

							58
Appendix
4. Remove the lamp unit.
•  Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction 
of the arrow.
   
5. Insert the new lamp unit.
•  Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
•  Attach the lamp unit cover.
•  Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then 
tighten the user service screw.
 Info
•  If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord 
is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1. Connect the power cord.
•  Plug the power cord into the AC socket of the 
projector.
2. Reset the lamp timer.
•  While holding down ,  and  on the projector, 
press  on the projector. (See page 50)
•  “LAMP 0H” is displayed, indicating that the lamp timer 
is reset.
 Info
Make sure to reset the lamp timer only when replacing 
the lamp. If you reset the lamp timer and continue to 
use the same lamp, this may cause the lamp to become 
damaged or explode.
mp chassis cover while replacing the lamp.xt to them until they have sufficiently cooled down.
nvironment.Made in Taiwan
Pr/Cr Pb/CbYPCDVI
STATUSEXIT
INPUTMENU
ECO
ENTER
ENTER
ENTER