Tascam FX D1000 Instrallation Manual

.
.
.
.
.
.
.
.
.
.
.
.. . .  . . . . .  . . . . .  . . . . .  . . . . .  . . .INSTALLATION INSTRUCTIONS
SOFTWARE LEVEL: Your TM-D1000 MUST be at software level 1.18 or higherfor this option to work properly.  To check your software revision level:
Power up the TM-D1000.
1) Press SHIFT and MEMO. The display should read:
2) Push DATA ENTRY button downwards 4 times until “SYSTEM” appears.
3) Rotate “DATA ENTRY(PUSH)” knob clockwise until the version appears.
If the software version is LESS than 1.18, the...

FX-D1000
10/08/99
Page 2 of 6TASCAM
TEAC Professional Division
7733 Telegraph Road
Montebello, CA  90640
Phone (323) 726-0303
Fax (323) 727-7632INSTALLATION INSTRUCTIONS
IMPORTANT WARNING!!!  Special care should be taken when re-installing the bottom coverscrews.  As the diagram above shows, the screws MUST be reinstalled in the same position as they wereremoved.  Note the location of the special 5mm screw!  If an 8mm screw is installed where the 5mm screwwas removed, the extra penetration by the 8mm...

FX-D1000
10/08/99
Page 3 of 6TASCAM
TEAC Professional Division
7733 Telegraph Road
Montebello, CA  90640
Phone (323) 726-0303
Fax (323) 727-7632INSTALLATION INSTRUCTIONS
DetachAttachinto the plastic case supplied with the new PLD.  Place it into the postage paid self-addressed
envelope provided and return to TASCAM.  Thank you!
STEP 4:  Installing the new PLD:  CAUTION:  The PLD is sensitive to static discharges and may bedamaged if improperly handled.  It is highly recommended that the installer be well...

FX-D1000
10/08/99
Page 4 of 6TASCAM
TEAC Professional Division
7733 Telegraph Road
Montebello, CA  90640
Phone (323) 726-0303
Fax (323) 727-7632INSTALLATION INSTRUCTIONS
STEP 7:Remove the FX-D1000 from its anti-static wrapping. Holding the FX-D1000 by its edges, orientit as shown in Figure 1.3. The component side of the board should be on the bottom.
STEP 8:The connector on the FX-D1000 should be inserted into connector CN5 on the main PCB. Fit thethree retaining studs you installed into the Main PCB...

FX-D1000
10/08/99
Page 5 of 6TASCAM
TEAC Professional Division
7733 Telegraph Road
Montebello, CA  90640
Phone (323) 726-0303
Fax (323) 727-7632INSTALLATION INSTRUCTIONS
STEP 11: Checking software operation:  Turn your TM-D1000 over so it is right side up and resting onits feet.  Reconnect the power cord.
Power up the TM-D1000
Confirm that the TM-D1000 recognizes the FX-D1000 with the following steps:
Press the SHIFT and PARAM SEL. buttons. The display should show:
Option
MODETurn the DATA ENTRY (PUSH)...

FX-D1000
10/08/99
Page 6 of 6TASCAM
TEAC Professional Division
7733 Telegraph Road
Montebello, CA  90640
Phone (323) 726-0303
Fax (323) 727-7632INSTALLATION INSTRUCTIONS
TABLE FOR OPTION/EFFECT/EFFECT PATTERN
LCD1st line2nd lineDescriptionSystemE f f e c t _ P a t t e r n _ _ _ _ _ _ _ _ _ _ C h _ D y n a m i c s _ _ _ _ _ _ _ _ _ _ _ _ ? Effect Pattern1WithoutL-R:Eff1_ _ _ _ _ Aux1-2:Eff2_?Effect Pattern2FX-D1000Aux1-2:Eff[Cascade1-2]_?Effect Pattern3Aux1-2:Eff[Cascade2-1]_?Effect Pattern4Aux1-2:Eff[_ _...