Home > TiE > Communications System > TiE Businesscom Plus 24/36/64 Installation Manual

TiE Businesscom Plus 24/36/64 Installation Manual

Here you can view all the pages of manual TiE Businesscom Plus 24/36/64 Installation Manual. The TiE manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 11

    Console 

Page 12

Speakerphones
2.16Speakerphones, which can be installed in Standard
telephones, permit handsfree CO conversations. The
maximum number of speakerphones permitted in each
system is as follows:
5.FCC AND TELCO REQUIREMENTS
SystemMaximum
2412
3612
6424
5.01 Rules and regulations for the operation and
installation of telephone equipment have been
established by the Federal Communications Commission
(FCC). According to Part 68, “Connection of Terminal
Equipment to the Telephone Network” and its amendments,...

Page 13


Page 14

Table SPECIFICATIONS,  PLUS 24
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.System Capacity:MAX. NO.CO Lines8Speakerphones12Intercom Talkpaths6OPX Telephones12
Key Telephones24
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
KSU/Power Supply Operating Range: 117 VAC 
 10%60 Hz  Hz
Power Dissipation:
 Supply Unit: 340 Watts  2.9 Amp
Grounding Requirements:1160 
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable Requirements:
Four...

Page 15

Table 1-2SPECIFICATIONS,  PLUS 36
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.System Capacity:MAX. NO.CO Lines12Speakerphones12
Intercom Talkpaths6OPX Telephones18
Stations 3 6
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
 Supply Operating Range: 117 VAC  10%
Power Dissipation:60 Hz  Hz
 Supply Unit: 480 Watts  4.1 Amps
Grounding Requirements:1638 
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable Requirements:
Four...

Page 16

Table H-3 SPECIFICATIONS,  PLUS 64
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.CO Lines 2 4
Intercom Talkpaths
6Stations64
System Capacity:
Speakerphones
OPX TelephonesMAX. NO.24
32
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
KSU/Power Supply Operating Range: 117 VAC 
 10%
Power Dissipation:
60 Hz  Hz
 Supply Unit: 870 Watts  7.4 Amps
Grounding Requirements:2968 BTU/HI=.
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable...

Page 17

BUSINESSCOM PLUS 
ELECTRONIC KEYTELEPHONESYSTEMS
SECTION 2,FEWTURES
CONTENTSPAGECONTENTSPAGE
1.INTRODUCTION..................... 2-2
2. DESCRIPTION......................
Automatic Intercom Answer...........
Background Music (BGM)............. 2-2
Call Duration Timer................. 2-2
Call Forward With Follow-Me..........
Call Monitor....................... 2-3
Call Pickup.......................
Call  Announced.............. 2-4
Call Transfer Unannounced............ 2-4
Call...

Page 18

1.INTRODUCTION
   
1.01This section lists and details the features available
in the Businesscorn Plus  Both
permanent and programmable features are discussed. This
section should be used in conjunction with Section 4,
SOFTWARE CONFIGURATION, when preparing the
Program Record Form.
2.DESCRIPTION
2.01This section is formatted in the following manner:
Description: discusses the basic elements of the feature.
Conditions: lists and describes conditions that limit or
enhance the feature under discussion.
Basic...

Page 19

Basic Programming:
Program  Duration Timer
Related Programming:
Program  Duration Start Timer
Feature Interactions:
CO Lines
Hold
CALL FORWARD  FOLLOW-ME
Description:
This feature permits the automatic transfer of an incoming
Intercom call to a second station (Call Forward). The
destination of the forwarded call can be changed to yet a third
station and so on (Follow-Me).
Conditions:
(a) The originating station can change the destination of the
Call Forward.
(b) Only the originating station can cancel a...

Page 20

 
 
CALL TRANSFER ANNOUNCED
Description:
Thisfeature permits the voice announced transfer of an
established CO call.
 
Voice Announce must be programmed.
Program 49 (Excluded System Features) can disable this
feature.
If the transferred call is not answered within a
programmed period of time, the call reverts back to the
transferring station.
This feature is accessible from a key telephone or DSS
Console.
Basic Programming:
Program 24-Voice Announce /Tone Signal Call
Related Programming:
Program  Console...
Start reading TiE Businesscom Plus 24/36/64 Installation Manual

Related Manuals for TiE Businesscom Plus 24/36/64 Installation Manual

All TiE manuals