Tone Commander 6210, 6220 User Manual

28Tone Commander 6210/6220 User Manual
Installation Options
Options in this section are typically set at the time of installation. Many
options can be set automatically by the AutoSPID, Automatic Switch
Detect, and Parameter Download features, if supported on the network.
The following options can be changed from the Installation Options
menu:
• SPID• Installation Password
• Parameter Download•  Reset to Default Settings
• Terminal Mode• Voice Announce
• Key Configuration
Installation Options Menu...

Tone Commander 6210/6220 User Manual29
A password may be set to prevent unauthorized entry
into the Installation Options menu.
When prompted for a password, enter your 4-digit
password with the dial pad. Press the Done key after
entering the password.
To change or remove the password, please refer to
page 37.
SPID Entry   _____________________________
A unique SPID (Service Profile IDentifier) is required for operation of
the 6210/6220. If the network supports AutoSPID, a SPID that is
assigned to your...

30Tone Commander 6210/6220 User Manual
Parameter Download  _____________________
(National ISDN only)
ISDN Parameter Download is an automated feature for configuring Call
Appearance and Feature Activator keys. If configured for auto
download, a Parameter Download is executed when the phone
initializes with a new SPID, or when requested by the network, due to a
line configuration change.
Note: Speed Dial and DSS keys are not configured by Parameter
Download.
From the Installation Options menu, select...

Tone Commander 6210/6220 User Manual31
From the Installation Options menu, select KEYS.
(Setup → INSTL → KEYS)
The status indicator for each key will indicate the current
setting.
Green– Call Appearance or DSS.
Red– Feature Activator.
Off– Unused or Speed Dial.
On the phone or expansion module, press the multifunction
key to be programmed.
The selected key’s indicator will alternately flash red and
green.
Select CA/DN (Call Appearance /Directory Number), FA
(Feature Activator), DSS (Direct Station...

32Tone Commander 6210/6220 User Manual
Automatic Call Appearance Selection
A call appearance is automatically selected when originating a new
call, answering an incoming call, or conferencing or transferring a call.
Three configuration options determine how call appearances are
selected:
Call Preference (page 61) – determines whether a new call is
originated when you lift the handset or press the Spkr key. If set to
NONE, you must manually press a Call Appearance key to originate
a call.
Originating DN –...

Tone Commander 6210/6220 User Manual33
Feature Activator Keys
Feature Activator keys must be configured to match network feature
activator codes that have been assigned to your line.
Using the dial pad, enter the feature activator code assigned
by your network service provider.
If you need to make corrections while entering numbers,
select 
ÅBKSP (backspace) to delete the previous digit.
Select CALL if a call needs to be originated when the feature
is activated. When enabled, (CALL) will appear in the...

34Tone Commander 6210/6220 User Manual
DSS Keys
DSS keys are a special type of Call Appearance/Directory Number
keys that are programmed with speed dial numbers to provide Direct
Station Selection. When the call appearance is idle or busy, DSS keys
act like Speed Dial keys, to call a station. When ringing, DSS keys act
like CA/DN keys, to answer a call. The LED indicator on the key shows
the status of the station’s call appearance (idle, ringing, hold, busy).
Shared call appearances for stations you wish...

Tone Commander 6210/6220 User Manual35
Speed Dial Keys
Keys not assigned for call appearances or feature activators may be
used as Speed Dial keys. Dial strings can include network feature
activator codes, to simplify the use of features such as Directed Call
Pickup and Call Forwarding. Speed Dial keys may also be programmed
from the User Options menu.
The currently programmed dial string, if any, will be shown in
the display.
Enter digits (24 maximum) with the dial pad.
Pauses are entered with the PAUSE...

36Tone Commander 6210/6220 User Manual
When digits have been entered, press the Done key twice to
return to the key selection menu or the Setup key to exit
Setup Mode.
Terminal Mode   __________________________
(National ISDN only)
If the network does not support Parameter Download, you must
manually select the terminal mode.
From the Installation Options menu, select MODE.
(Setup → INSTL → More
4 → MODE)
Select the terminal mode based upon the type of service that
was ordered from your network service...

Tone Commander 6210/6220 User Manual37
Installation Password   ____________________
You can set a password to prohibit unauthorized entry into the
Installation Options menu.
If a password is currently set, the display will prompt you to enter your
password prior to making changes.
From the Installation Options menu, select PASSWD.
(Setup → INSTL → More
4 → PASSWD)
Select SET.
Enter a new 4-digit password with the dial pad.
If you need to change a password digit after entering it, select
ÅBKSP (backspace)...