Toshiba Strata Dk24, 56, 96 Quick Reference Guide

							To set up a Two CO LineConnection:
bWhile on an outside call established
on a CO button, press the CONW
IRNSbutton.
bPress another CO button and dial a
telephone number.
bPress theCONFRRNS button afterthe called 
parly answers.
b PresstheCONFlTRNS button
again, then hang up.
bThe two outside parties are
conversing.
0
lsl
Q U I C K
REFE-RENCEG U I D E
STRATA DK
24/56/96 
						

							To enter a Forced
Account Code:
bAccess an outside line by dialing a
line access code or pressing a
CO or 
PL button.
)Enter the Forced Account Code.
bListen for dial tone.
b Dial a telephone number.
To enter a Voluntary
Account Code:
)After seizing a CO line or while on
a call: Press the 
ACCNT button;
or dial * 5 0; or press the 
CONW
TRNS button and dial 4 6.
)Enter the Account Code
To activate Automatic
Busy Redial:
)After dialing an outside telephone
number, press the ARR button,or press the 
CONFmNS button
and dial 4 4.
)Your telephone will signal you
when the called number becomes
not busy.
)To cancel Automatic Busy Redial,
press the ARR button, or pressthe 
INT button and dial 4 4.
To activate Automatic
Callback:
)After dialing a busy station or
station in the Do Not Disturb
mode, press the 
ACE button or
dial 4.
)-Hang up. The system will call youback when the station becomes
available.
To redial the Last
Number Dialed:
)Lift the handset and press any
available CO button.
)Press the RDL (or #) button.
To “Save” a number toredial later: 
-
)Any time after dialing a telephone
number and before disconnecting
the call, press the 
SAVE button.
To redial a “Saved”
number:
) Access an outside line, then press
the 
SAVE button.
To store a Speed Dial
number:
)Press the RDL (or #) button, then
the 
SDS (*) button.
bPress the SD button you want to
store the telephone number on, ordial a Speed Dial access code
(1 0 - 4 9 for Station SpeedDial, 6 0 
- 9 9 for System
Speed Dial) where you want to
store the number.
b Enter the telephone number, then
press the RDL (or #) button.To make a call with
Speed Dial:
b Access an outside line.
bPress a SD button, or press the
SDS (or *) button and dial aSpeed Dial access code
(1 0 
- 4 9 for Station Speed
Dial, 6 0 
- 9 9 for System Speed
T)iall. 
						

							To leave a Message
Waiting Indication at
another station:
)After reaching a busy or
unanswered station, press the
MWfiL button.
To answer a Message
Waiting Indication at your
station:
) The Message Waiting Indication is
indicated by a flashing 
MWlFL
LED.
)Lift the handset, press the INTbutton, then press the 
Mw/FLbutton to call back the station or
voice mail device that left the
indication.
To make a Busy Override
or Executive Override
call:
)To make a Busy Override call, dial2 after dialing a busy station.
) To make an Executive Override
(barge-in) call, dial 3 after
reaching a busy station.
To make a Page
announcement:
.
)Lift the handset and press the BITbutton.
bTo page all stations in the All Call
Page group, dial 3 0; station
groups, dial 3 1 
m 3 4; the All Call
Page group with external pagezones optionally included, dial
3 9; external page zones, dial
35-38.To set Call Forward with
a Call Forward button:
)Press a Call Forward button:
CFAC, CFB, CFBA, or CFB/NA.
bEnter the station number to which
calls will forward.
bPress the Call Forward buttonagain. 
-To set Call Forward with
an access code:
)Press the BIT button and dial a
Call Forward access code: CallForward-All Calls, 6 0 4; Call
Forward-Busy, 6 0 2; Call
Forward-No Answer, 6 0 3; Call
Forward-Busy/No Answer, 6 0 4.
bEnter the number of the station to
which calls will forward.
bPress the SPKR button.
To cancel Call Forward:
)Press the same Call Forwardbutton that you used to set Call
Forward; or press the INTbutton, dial 6 0 1, then press the
SPKR button.To Park a call:
)While on a call, press the CONF/
TRNS button and dial 4 1.
To retrieve the Parked
call:
bPress the BIT button and dial 4 2. 
						

							To Pick Up a call:)Press the PKUP button or dial 5.
bTo pick up a call that is ringing or
held at a station, dial the station
number; for an intercom page or
ringing door phone, dial 3 0; on
an external page, dial 3 5; for a
CO line on hold, dial 7 0 1 
-7 3 6; for any ringing CO line,
dial 9.
To Transfer a call:
bWhile on a call, press the CONW
TRNS button and dial a station
number.
FIf the station is idle: Wait for the
station to answer, make a voice
announcement and hang up.
bIf the station is busy: Hang up.
To make a ConferenceCall:
bWhile on a call, press the CONW
TRNS button.
bTo add an outside line to the call,
access an outside line and dial a
telephone number; to add a
station to the call, dial a station
number.
b Press the CONF/TRNS button
after the called party answers. All
parties are 
conferenced together.
To activate/deactivate
Do Not Disturb:
bTo activate, press the DND buttonso that the LED lights; to
deactivate, press the button again
so that the LED turns off.
To place a call on
Exclusive Hold:
b Press the HOLD button twice.
)No one can accidentally pick up
your call.
To receive a Handsfree
Answerback call:
bYou will hear a single warning tonefollowed by the caller’s voice.
F Without lifting the handset, speak
toward the telephone at a normal
voice level to answer the caller.
To use Handsfree
Monitoring:
b While holding down the SPKR
button during a call, place the
handset on-hook.
) Release the SPKR button.
bLift the handset to resume the
conversation.To make an outside call:
bPress a CO or PL button; or, press
the 
INT button and dial a lineaccess code (7 0 I- 7 3 6,
8 1 -8 8, or 9).
bDial a telephone number, and lift
the handset when the called party
answers.
To make a call to another
station:
FLift the handset and press the NIT
button.
b Dial a station number.