TP-Link Router TL-R460 User Manual

TL-R460Cable/DSL Router User Guide
 
 
4
The rear panel contains  the following features. 
¾  POWER:  The Power plug is where you  will connect the power adapter. 
) Note: 
Please use the power adapter supplied with t he TL-R460 Cable/DSL Router, if you use a 
different adapter, it may c ause damage to the Router.  
¾  RESET:  Use the button to  reset the routers factory defaults. There are two ways to 
reset the routers factory defaults: 
1. Use the  Factory Defaults  function on System Tools  ->...

TL-R460Cable/DSL Router User Guide
 
 
5
2.4  Connecting the Router 
Before you install the router, you should connec t your PC to the Internet through your 
broadband service successfully. If there is any  problem, please contact with your ISP for 
help. After that, please install the router acco rding to the following steps. Dont forget to 
pull out the power plug and keep your hands dry. 
Step 1:  Locate an optimum location for the Router.  The best place is usually near the 
center of the area in...

TL-R460Cable/DSL Router User Guide
 
 
6
 
Chapter 3.  Quick Installation Guide 
After connecting the TL-R460 router to your  network, you should configure it. This 
chapter describes how to c onfigure the PC and the Router to access the Internet 
immediately after it has been successfully  configured (take Windows XP for example). 
3.1 Configure PC 
Step 1:  Click the  Start menu on your desktop, right click  My Network Places, and then 
select  Properties  (shown in Figure 3-1). 
 
Figure 3-1 
Step 2:...

TL-R460Cable/DSL Router User Guide
 
 
7
 
Figure 3-2 
Step 3:  In the next screen, select  General tab, highlight Internet  Protocol (TCP/IP), and 
then click the  Properties button.
  

TL-R460Cable/DSL Router User Guide
 
 
8
 
Figure 3-3 
Step 4:  Configure the IP addr ess as shown in Figure 3-4. After that, click  OK.  

TL-R460Cable/DSL Router User Guide
 
 
9
 
Figure 3-4 
)  Note:  
You can c onfigure the PC to get an IP address autom atically, select “Obtain an IP address 
automatically” and “Obtain DNS server addre ss automatically” in the screen above.   
Now, you can run the Ping command in the  command prompt to verify the network 
connection. Please click the  Start menu on your desktop, select  run tab, type  cmd in the 
field, and then type  ping 192.168.1.1 on the next screen, and then press  Enter. 
If the...

TL-R460Cable/DSL Router User Guide
 
 
10
If the result displayed is similar to the screen  shown below, it means that your PC has not 
connected to the Router. 
 
Figure 3-6 
You can check it follow the steps below: 
)  Note: 
Is the connection between your PC and the Router correct? 
The LEDs of LAN port which you link to the device and the LEDs on your PCs adapter 
should be lit. 
Is the TCP/IP configuration for your PC correct? 
If the Routers IP address is 192.168.1.1, your PCs IP address  must be...

TL-R460Cable/DSL Router User Guide
 
 
11
 
Figure 3-7 
)  Note: 
If the above screen ( Figure 3-7) does not prompt, it m eans that 
 your web-browser may be 
set to a proxy. Choose  Tools menu→Internet Options →Connections→LAN Settings, 
in the screen that appears, cancel the  Using Proxy checkbox, and click OK to finish it. 
Step 1:  Select the  Quick Setup  tab on the left of the main menu and the “Quick Setup” 
screen will appear. Click the  Next button. 
 
Figure 3-8 
Step 2:  Select the connection...

TL-R460Cable/DSL Router User Guide
 
 
12
 
Figure 3-9 
)  Note: 
The router supports three popular ways to  connect to Internet. Please select one 
compatible with your ISP, if you are given  another way that is not listed here, refer to 
Network → WAN for detailed list. 
Step 3:  If you choose PPPoE , you will see the screen as shown in  Figure 3-10, enter 
the  Userna

me  and Password  provided by your ISP. These fields are case 
sensitive. If you have difficulty with th is process, please contact...

TL-R460Cable/DSL Router User Guide
 
 
13
 
Figure 3-11 
Step 6:  After that, you will see the next screen. Click  Finish to complete the quick 
installation. 
 
Figure 3-12