TP-Link Router TL-WR740N User Manual

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 44 - 
3. Select Enabled or Disabled  for this entry on the  Status pull-down list. 
4. Click the  Save button to save this entry. 
To modify or delete an existing entry: 
1. Click the  Modify in the entry you want to modify. If  you want to delete the entry, click the  
Delete. 
2.  Modify the information.   
3. Click the  Save button. 
Click the  Enable All  button to make all entries enabled 
Click the  Disabled All  button to make all entries disabled....

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 45 - 
4.6.4 Wireless Advanced 
Choose menu “ Wireless → Wireless Advanced ”, you can configure the advanced settings of 
your wireless network. 
 
Figure 4-23 Wireless Advanced 
¾  Transmit Power -  Here you can specify the  transmit power of Router. You can select High, 
Middle or Low which you would like. High  is the default setting and is recommended. 
¾ Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. 
The beacons...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 46 - 
specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates 
the DTIM Interval is the same as Beacon Interval.   
¾  Enable WMM - WMM  function can guarantee the packets  with high-priority messages being 
transmitted preferentially. It  is strongly recommended.   
¾ Enable Short GI -  This function is recommended for it  will increase the data capacity by 
reducing the guard interval time
.  
¾  Enabled AP Isolation -...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 47 - 
) Note:  
This page will be refreshed autom atically every 5 seconds. 
4.7  DHCP 
 
Figure 4-25    The DHCP menu 
There are three submenus unde r the DHCP menu (shown in Figure 4-25), DHCP Settings , 
DHCP Clients List  and Address Reservation.  Click any of them, and you will be able to 
configure the corre sponding function. 
4.7.1 DHCP Settings 
Choose menu “ DHCP → DHCP Settings ”, you can configure the  DHCP Server on the page as 
shown in...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 48 - 
¾ End IP Address -  Specify an IP address for the DHCP Server to end with when assigning IP 
addresses. 192.168.1.199 is  the default end address. 
¾ Address Lease Time -  The Address Lease Time  is the amount of time a network user will 
be allowed connection to the Rout er with their current dynamic IP Address. Enter the 
amount of time in minutes and t he user will be leased this dynamic IP Address. After the 
time is up, the user will be...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 49 - 
You cannot change any of the values on this page. To update this page and to show the current 
attached devices, click the  Refresh button. 
4.7.3 Address Reservation 
Choose menu “ DHCP → Address Reservation ”, you can view and add a reserved address for 
clients via the next screen (shown in  Figure 4-28).When you specify a reserved IP address for a 
PC on the LAN, that PC will always receive the  same IP address each time when it accesses the...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 50 - 
To modify or delete an existing entry: 
1. Click the Modify in the entry you want to modify. If  you want to delete the entry, click the  
Delete. 
2.  Modify the information.   
3. Click the  Save button. 
Click the  Enable/Disabled All  button to make all entries enabled/disabled 
Click the  Delete All  button to delete all entries. 
Click the  Next button to go to the next page and Click the  Previous button to return the previous 
page.  
4.8...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 51 - 
¾ Service Port - The numbers of External Ports. You can type a service port or a range of 
service ports (in XXX – YYY format, XXX is  the start port number, YYY is the end port 
number).  
¾  IP Address -  The IP Address of the PC pr oviding the service application. 
¾ Protocol -  The protocol used for th is application, either TCP, UDP , or All (all protocols 
supported by the Router). 
¾  Status -  The status of this entry, either  Enabled or...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 52 - 
3. Click the Save button. 
Click the  Enable/Disabled All  button to make all entries enabled/disabled. 
Click the  Delete All  button to delete all entries. 
Click the  Next button to go to the next page and click the  Previous button to return the previous 
page.  
) Note: 
If you set the service port of the virtual server as 80, you must set the Web management port on 
“ Security  → Remote Management ” page to be any other value except 80 such as...

TL-WR740N/TL-WR741ND150Mbps Wireless N Router 
- 53 - 
¾ Incoming Ports Range -  The port or port range used by the remote system when it 
responds to the outgoing request.  A response using one of these ports will be forwarded to 
the PC that triggered this rule. You can input  at most 5 groups of ports (or port sections). 
Every group of ports must be set apart with  ,. For example, 2000-2038, 2050-2051, 2085, 
3010-3030. 
¾  Incoming Protocol -  The protocol used for Incoming Ports Range, either  TCP...