Trillium Panther 306 Technical Service Manual

							Technical 
Service 
Manual (- Feature 
Programming 
,_._...._.......................::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::................................................................,.........._ _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
:::::::::::: ,.........,.......... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I . . . . . . . . . . . . . . . . _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 
i 
INDIVIDUAL SET FEATURES 
CAUTION 
Set BATTERY to ON at the KSU to prevent 
loss of entered feature programming selections. 
To 
program individual Set features from 
station 10. . . . 
2 
I 1 Then, to program a selected feature at a se- 
At the KSU, set 
PROGRAM 2 
to ON. 
At the KSU, 
press RESET. 
lected station: 
At station 10, the 
Mic.on/off indicator 
FLASHES after a few 
seconds. 
3* 
4* 
5 Dial the selected 
program code: dial 
the first digis then 
the 2digit number 
of the selected Set 
(10 through 15 - 
represented by Yy), 
and finally the last 
digit. 
Programthedesired 
condition for the 
selected feature by 
pressing the line 
1,2,and3keys 
and the 
Intercom 
key - or by dialing 
a specified nuinber, 
using the key pad, 
if so instructed. 
Press the 
Hold 
key. The 
Mic.on/off 
indicator goes OFF. 
The indicators for lines 
1,2,and3andthe 
indicator for 
Intercom 
display the pattern 
shown in the table on 
the facing page. 
The Mic.on/off 
indicator FLASHES. 
Then, to program another Set - or another 
feature (if all desired features have been pro- 
Finally, to exit the programming mode and 
save all your programming selections: 
At the KSU, set 
PROGRAM 2 to 
OFF. . . . 
’ At theKSU, At station 10, the 
press RESET. 
Mic.on/off indicator 
goes OFF. 
To return all features to their preprogrammed 
(factory default) conditions . . . 
Step Action 
Respome 
1 
AttheKSU,set . . . 
PROGRAM 1 to 
ON. 
2 
At the KSU, 
.f. 
press RESET. 
3 AttheKSU,set . . . 
PROGRAM 1 to 
OFF. 
4 
At the KSU, . . . 
press RESET again. 
NOTE 
Individual Set features may be programmed in 
any order. Also, you may program as many or 
as few features or Sets as you desire. Therefore, 
in the table on the facing page, feamres are 
listed in alphabetical order to help you find the 
-. features you want quickly. 
* See the Program Code, Condition Description, 
and Indicator Status column entries in the 
feature pro- 
gramming table on the facing page. 
C 
. . . . . .._. _ . . . . .._._ __ _....... _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-....... _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .f . . . . . . . . ..I..... - . . . . . . . . . . . . . - . . . . . . . . . . . . . ..- . . . . . ............................ _ ......... -......... ................. 
. . . . . . . . . ...” ..,.. __“..“” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a . . . . . . . . . . . . . . . . . . . . . . . . . . . a... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a . . . . . . . . . . . . . -.. . . . . . ..I.... - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . “.” . . . . . . . . . . . . . . . . . ,-- 
Panther 306. I TRILLIUM ( 
Page F-S 
Telephone 
Systems  
						

							Technical 
Service Feature 
Manual Programming 
. . . . . . . . . . . . . . . . . .._........s............ 
, . . . . . . . . . . . . . ,..- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- . . . . . . . . . . . _ . . . . ....._.................................................................................. . . . . . . . . . . . . . . . . . .._........e....................” . . . . *.... . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..- _ ........._....... - .,..................................... _ .._....................................., 
Feature Program Feature Condition 
Indicator 
Name Codet Category Description* 
Status 
Barge-In 4YYo Individual Set 
No barge-in 
Intercom off 
Call 
Restrictions IYYI Individual Set Barge-in 
Intercom .on 
Class 
A Lines 1 and 2 off 
Class B 
Line 1 on: line 2 off 
Class c Line 2 on; line 1 off 
Line 3YYo Individual Set 
No group (OO)** 
Intercom and lines 1.2, and 3 off 
Group Group 1 (Ol)** Line 
1 on: Intercom and lines 2 and 3 off 
Assignment Group 2 (02)** Line 2 on; 
Intercom and lines 1 and 3 off 
Group 3 (03)** Lines 1 and 2 on; 
Intercom and line 3 off 
Group 4 (O4)** Line 3 on; 
Intercom and lines 1 and 2 off 
Group 5 (05)** Lines 1 and 3 on; 
Intercom and line 2 off 
Group 6 (06)** Lines 2 and 3 on; 
lnte.rcom and line 1 off 
Group 7 (07)** Lines 1 
,2, and 3 on; Intercom off 
Group 8 (08)** 
Intercom on; lines 1.2, and 3 off 
Group 9 (O9)** 
Intercom and line 1 on; lines 2 and 3 off 
Group 10 (lo)** 
intercom and line, 2 on; lines 1 and 3 off 
Group 11 (ll)** 
Intercom and lines 1 and 2 on; line 3 off 
Group 12 (12)** 
Intercom and line 3 on; lines 1 and 2 off 
Night Transfer 4YYo Individual Set No transfer 
Line 2 off 
Ringing Tmns 
fe; Line 2 on 
Ringing 2YYo Individual Set No ringingttt 
Lines 1.2, and 3 offtt 
Assignment Ring on line 1 calls 
Line 1 ant? 
Ring on line 2 calls 
Line 2 ontf 
Ring on line 3 calls*** 
Line 3 ont? 
3Wl Individual Set No zones (OO)** 
Intercom and lines 1,2, and 3 off 
Paging Zone 1 (Ol)** Line 1 on; 
Intercom and lines 2 and 3 off 
Zone 2 (02)** Line 2 
Intercom and lines 1 and 3 off  on; 
Zone 3 (03)** Lines 1 and 2 
Intercom and line 3 off  on; 
Zone 4 (O4)** Line 3 
Intercom and lines 1 and 2 off  on: 
Zone 5 (05)** Lines 1 and 3 
Intercom and line 2 off  on; 
Zone 6 (O6)** Lines 2 and 3 
Intercom and line 1 off  on: 
t YY stands fol desired station number (10 through 15). 
tt A Set may be programmed to ring on any or all of the incoming lines by pressing the indicated keys; obswve that the 
corresponding indicators go ON. 
+tt Station 10 is preprogrammed to ring on all lines: all other stations are preprogrammed not to ring on any line. 
* 
Preprogrammed (factory default) conditions are shown in bold type. 
** Dial the number in parentheses using the key pad; observe that the desired indicator pattern appears (see Indicator Status 
column). 
*** Rings when door button is pressed on Door Module 1 or 2 (if optional Door Answer Unit is installed). 
Individual Set Feature Programming Table 
TRILLIUM 
Telephone 
Systems Panther 306 
Page F-9  
						

							Feature 
Programming Technical 
Service 
Manual 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ** . . . . . . . . . . . . . . :::::::::=:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::~~:::::::::::::::::~:::::::::::::::::::::::::::::::::::::::::::::::::::::~:::::::::::::::::~.:::::::::::~~::~:::~.:::::::::::::::::::::::: 
INDIVIDUAL LINE FEATURES 
CAUTION 
Set BATTERY to ON at the KSU to prevent 
loss of entered feature programming selections. 
To 
program individual line features from 
station 10, . . . 
Stew I Action I ResDonse 
1 At the KSU, set 
PROGRAM 2 
to ON. 
2 At the KSU, 
press RESET. At station 10, the 
Mic.on/off indicator 
FLASHES after a few 
seconds. 
ted feature for a se- 
The Mic.on/off 
indicator goes OFF. 
the first digit, then 
the 2digit number 
of the selected line 
(01 
through 03 - 
represented by xx). 
Programthedesired 
condition for the 
and the 
Intercom 
The indicators for lines 
1,2,and3andthe 
indicator for 
Intercom 
display the 
pattern 
shown in the table on 
the facing page. 
hess the Hold The Mic.on/off 
indicator FLASHES. 
desired features have been pro- 
Finally, to exit the programming mode and 
save all your programming selections: 
At the KSU, set 
PROGRAM 2 to 
OFF. 
At the KSU, 
press RESET. At station 10, the 
Mic.on/off indicator 
goes OFF. 
To return all features to their preprogrammed 
(factory default) conditions . . . 
Step 
1 
2 
3 
4 
Action 
At the KSU, set 
PROGRAM 1 to 
ON. 
At the KSU. 
press RESET. 
At the KSU, set 
PROGRAM 1 to 
OFF. 
At the KSU. 
press RESET again 
Response 
.*. 
. . . 
. . . 
. . . 
NOTE 
Individual line features may be programmed in 
any order. Also, you may program as many or 
as few features or lines as you desire. 
Therefore, in the table on the king page, fea- 
tures are listed in alphabetical order to h&p you 
find the features you want quickly. 
* See the Program Code, Condition Description, 
and Indicator Status column entries in the feature pro- 
gramming table on the facing page. 
Panther 306 
Page F-10 TRILLIUM 
Telephone 
Systems c  
						

							Technical 
Service 
Manual Feature 
Programming 
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . :::::::::::::::::::::::::::::::::::::::::::::::::::::::::: . . . . . . . . . . . . - . . . . . . . . ..._..” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-.................................................  . . . . . . . . . . . . . _ _.........-........................................................................................................... _ . . . . :-s::::: ::::::::::::::::::::::::::::::: 
Feature Program Feature Condition Indicator 
Name Code* Category Description* Status 
Incoming 5xX0 Individual line No 
Line 3 off 
Calls Only YeS Line 3 on 
Telephone or 5xX0 Individual line 
Telephone Line 2 off 
PBX Line PBX Line 2 on 
Tone or 5xX0 Individual line 
Tone Line 1 off 
Pulse Pulse Line 1 on 
t XX stands for desired line number (01 
through 03). 
* 
Reprogrammed (factory default) conditions are shown in bold type. 
Individual Line Feature Programming Table 
TRILLIUM 
‘-. 
Telephone 
Systems Panther 306 
Page F-l 1  
						

							Feature 
Programming Technical 
Service 
Manual 
INDIVIDUAL GROUP FEATURES 
CAUTION 
Set BATTERY to ON at the KSU to prevent 
loss of entered feature programming selections. 
1 At the KSU, set 
PROGRAM 2 
to ON. 
2 At the KSU, 
press RESET. 
ct1 ed feature for a se- 
Then, to program a selec 
r lected group: 
3* 
4* 
5 Dial the selected 
prog.ramcxxkdial 
the first digit, then 
the 2digit number 
of the desired group 
(01 through 12 - 
represented by zz>, 
and finally the last 
digit. 
Programthedesired 
condition for the 
selected feature by 
pressing the line 
1,2,and3 keys 
and the 
InterCOrTI 
key . 
Press the 
Hold 
key. At station 10, the 
Mic.on/off indicator 
FLASHES after a few 
seconds. 
The Mic.on/off 
indicator goes OFF. 
The indicators for lines 
1,2,and3andthe 
indicator for 
Intercom 
display the pattern 
shown in the table on 
the Eating page. 
The 
Mic.on/off 
indicator FLASHES. 
Then, to program another group - or another 
feature (if all desired features have been pro- 
grammed, go to step 7): 
your programmlng se 
At the KSU, set 
PROGRAM 2 to . . . 
At station 10, the 
Mic.on/off indicator 
goes OFF. 
To return all features to their preprogrammed 
(factory default) conditions . . . 
Step 
1 Action 
Response 
At the KSU, set 
PROGRAM 1 to 
ON. . . . 
At the KSU, 
press RESET. 
At the KSU. set 
PROGRAM 1 to 
OFF. 
. . . 
. . . 
At the KSU, 
press RESET again. 
* See the Program Code, Condition Description, 
and Indicator Status column entries in the feature pro- 
gramming table on the facing page. 
I.- 
i- 
Panther 306 
Page F-12 TRtLLlUM 
Telephone 
Systems  
						

							Technical 
Service Feature 
Manual Programming 
! . . . . . . . . . . . . . . __ . . . . . -_... ..- . . . . . . . . . . . ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::~:::::::::::::::::::::::::::::::::: :::::::: ::: ::::::::::::: :::::::::::::-“::::::::::::::::::::::: :::::::: I= ::::::::: ‘: 
. . . . . . . . . . . . . . c . . .._... _ . . . . . . . . . . . . . 
Feature Program Feature Condition Indicator 
Name Codet Category Description* Status 
Line Individual 
All lines** Lines 1,2, and 3 onl’r 
Grouping 
group Remove line 1 Line 1 offtt 
Remove line 2 Line 2 offtt 
Remove line 3 Line 3 offtt 
t ZZ stands for desired group number (01 through 12). 
tt Any line or combination of lines may be assigned to a ‘group by not pressing the desired line keys; observe that 
the corresponding indicators are ON. 
* preprogrammed (factory default) conditions are shown in bold type. 
*+ If the Line Group Assignment feature (code 3YYO) is programmed for any condition other than no group (its preprogrammed 
condition) - that is, if any Sets have been assigned to any group 
- then the preprogrammed condition is for all outside 
lines to be assigned to each active group. 
Individual Group Feature Programming Table 
. . . . . . . . . . . . - . .._ .,.: :: ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::z . . . . . . . . . . . ..-. ~ . . . . . . . . . . . . . . . . . . . . . . . . . . . . _ . . . .._._......._................................................. ~ . . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . .._ . . . . . . . . . . . . . -- . . . . . . . . . . I.... . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . . -........- . . . . . . . . . . . ...” . . . . ..I..................... _” . . . . . . . . . . . . . . . . . . . . . . . . . . . - . . . . . - 
: 
 TRILLIUM 
._ 
Telephone 
Systems Panther 306 
Page F-13  
						

							Feature 
Programming Technical 
Service 
Manual 
:::::::::::::::::::::::::::.-..--... a . . . . . . . . . G . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..- _ ._......_....... _ . . ... v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . _ . ............. _ ..... ::::::::::::::::::::::::::::_=::::::::::::::::::::::::::::: :::::: k 
SPEED CALL NUMBERS 
Speed Call Programming Notes 
NOTES 
1. 
Entries up to 26 digits long may be stored 
as speed call numbers. 
2. Pressing the Hold key as part of the speed 
call number programming sequence inserts a 
halt in the dialing sequence; pressing the 
Flash/Cancel key inserts a hookswitch 
flash; and pressing the 
Conference key in- 
serts apause. 
You may insert as many halts, flashes, and 
pauses as you wish as long as the total key 
entry count does 
not exceed 26. 
3. Up to 34 common speed call numbers may 
be programmed into the system - but only 
from station 10. 
Additionally, up to 11 private speed call num- 
bers may be programmed at each individual 
station. 
step 
1 
2 
3 
I 
Common Speed Call Numbers 
NOTE 
During common speed call number program- 
ming, the user at station 10 will. leave the 
station’s handset in its cradle and listen to the 
indicated aural responses over the speaker. 
A continuous tone is 
heard over the Set’s 
The 
Intercom 
indicator FLASHES. 
Dial the number 
The continuous tone 
Intercom indicator 
continues to FLASH. 
Speaker key. 
indicatcr goes OFF; and 
the Set returns to normal 
I 
Operation. 
-. 
_. 
................................ - 
................. ......... ...... . ..- ‘::::::::::::::“::::~~:::::~~::::::::::::::::::::~::~::::::::~ -...- . . . . . . . . . . . . . . . . . . . . . . . . 
. . . . . . . . . . . . . . . . . . . - . .._..._...._ - . . . . . . . . . . . . . . . ,, . . . . . 
..- . . . . . . . . s.... . . . . . I..... . . . . . . . . . . . . . . . . - . . . . . . . . . . . . . - . . . . “.- . . . . . . . . . . . . . . . 
. . . . . . . . . ..__.......... ~ . 
. ...” . . . . . . . . . . . . - ,~“~_, 
Panther 306 TRILLIUM c;, 
Page F-14 
Telephone ” 
Systems  
						

							Technical 
Service 
Manual Feature 
Programming 
................................................................................................ -. ................... . L.. ............... ..- 
........................................................................... -. 
................ ..- ....... . ......... -. ......... . ...... ................................................................................................................................. 
A.. 
..... .._ .................................................................................................................... 
Private Speed Call Numbers FEATURE DESCRIPTIONS 
NOTE 
During private speed call number program- 
ming, the station user will leave the station’s 
handset in its cradle and listen to the indicated 
aural responses over the speaker. 
To program up to 11 private speed call 
numbers into the system . . . 
Step 
1 
2 
3 
r 
Action 
Press the Speed 
key. 
For 
the first 5 speed 
call 
numbers, press 
the desired station/ 
‘speedcallkey(11 tc 
15); for the last 6 
private speed call 
numbers, dial the 
desiredspeedcall 
code (05 to 10). 
Dial 
the number 
you wish to store 
for the selected 
speed call key. 
Response 
A continuous tone is 
heard over the Set’s 
speaker;andthe 
Intercom indicatar 
WIN-KS 
slowly. 
The 
Intercom 
indicator FL,ASHES. 
The continuous tcue 
stops; and the 
Intercom indicator 
continues to FLASH 
1 To program another speed call number: 
4. 
Return to step 1. . . . 
To stop speed call number programming: 
5. Press the 
Speaker key. 
The Intercom 
indicator goes OFF; and 
the Set returns to normal 
OpXhIl. 
NOTE 
Since the same 5 keys are used to select sta- 
tions and to select one of your first 5 private 
speed call numbers, the SPEED key must be 
pressed before pressing the desired private speed 
call key when dialing one of your first 5 pri- 
vate speed call numbers 
with aura hold 
enabled. 
Auto Hold (program code 0001, preprogrammed for no 
auto hold) - allows a call to be simultaneously placed on 
hold and transferred by pressing the desired station select 
key. 
Barge-In (prograin code 4YY0, preprogrammed for no 
barge-in) - allows selected stations to override the privacy 
feature and enter an outside call that is in progress; an intru- 
sion tone is sounded to alert the call-in-progress parties of 
the barge-in. 
Call Restrictions (program code IYYl, preprogrammed 
for Class 
A) - 
assigns stations to one of three call restric- 
tion classes: 
Class A = no restrictions 
Class B = prevented from dialing 0 or 1 as the first 
digit, from dialing the number of digits to deny (see 
Digits-to-Deny), or from dialing any of the specific 
restriction entries (see 
Flexible Call Restrictions) 
Class C = 
no outside calls can be placed (but intercom 
calls can be placed or received, and incoming outside 
calls can be received, depending on line group 
programming). 
Digits-to-Deny (program code 0051, preprogrammed for 
the 8th digit) - determines which digit will be denied on a 
dialing attempt under Class B restrictions (see Call 
Restrictions). 
. . . . . . . . . . . . . . _ ^._._ _.::::::::: :::::-:::: :::::::::::::::::::=::::::::::::::::::=L:-‘::::::::::::::::”-:::::::::~~ :::::: “.:; :::::::::::::::::::::::::::::::::::::::::: ~~=‘-::~-~=“:I: :::::::::::::::::::::::::::::::::: 
. . . . . . . . . . . . . . “_ 
TRILLIUM 
I 
Telephone Panther 306 
Systems Page F- 15  
						

							Feature 
Programming ‘Technical 
Service 
Manual 
::::: 
::::::::::::::::::::::::::::::::::::::::::: :::::::: ;.: ::::: :: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .......................................................................... 
- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................................................................ ::::::::::: c- 
Flash or Cancel (program code 0011, preprogrammed for 
cancel) - define-s the function of the 
Flash/Cancel key, 
ho&switch flash or cancel signal for ending calls. (The le- 
ngth of this signal must be properly set to provide the 
desired function; refer to Flash or Cancel Duration). 
NOTE 
Generally, a flash signal’is 500 milliseconds 
long, and a cancel signal is 1 second long; to 
make sure you choose the correct length, check 
the specifications for your PBX 
. 
Flash or Cancel Duration (program code 0060, prepro- 
grammed for 1 second) - sets the length of the flash or 
cancel signal (see Flash or Cancel). 
Flexible Call Restrictions (no program code when not 
programmed, which is the factory default condition; program 
codes 7000 through 7900 are available for entering up to ten 
user-defined 3digit sequences) - allows 3digit sequences, 
such as 411 or specific area codes, to be denied for Class B 
stations (see Call Restrictions). 
Hold Recall Time (program code 0000, programmed for 
no recall) - enables reminders that you have a call on hold. 
Incoming Calls Only (program code .5Xx0, prepro- 
grammed no - to allow outgoing calls) - allows (no) or 
prevents (yes) outgoing calls on the indicated lines. 
Interdigit Pause (program code 0010, preprogrammed for 
800 milliseconds) - sets the time between dialed 
pulses 
(see also 
Tone or Pulse). Line Group Assignment (program code 3YY0, prepro- 
grammed for no group) 
- assigns the line groups defined 
under Line Grouping to be assigned to the indicated sta- 
tion (see also Line Group Type). 
Line Grouping (program code 6220, preprogrammed for 
all lines) - assigns outside lines to one of 12 groups, tbere- 
by defining each group. (See also Line Group 
Assignment and Line Group Type.) 
Line Group Type (program code 0011, preprogrammed 
for Type A) - assigns one of four sets of characteristics to 
line groups. 
NOTE 
The more commonly chosen line group types 
areTypeAandTypeD. 
Type A = Sets assigned to a line group can only make 
and answer calls on lines within the group. 
Type B = Sets assigned to a line group can make and 
answer calls on lines within the group -plus 
they can 
answer calls ringing in another group. 
Type C = Sets assigned to a line group can make and 
answer calls on lines within the group -plus 
they can 
receive calls transferred from another group. 
Type D = Sets assigned to a line group can make and 
answer calls on lines within the group 
-plus they can 
answer calls ringing in another group and can receive 
calls transferred from another group. 
(See also Line Group 
Assignment and Line 
Grouping.) 
Make-Break Ratio (program code 0010, preprogrammed 
for 40 %) - 
sets the on/off ratio of 
pulses (see also Tone 
or Pulse). 
:::::::::::~~::::::::::::::~::::::::::::::~::::~::::::::::::::::~::::::::::::::::::::::::::::::::::::::::::::::~:~::~~::::::::::::::::::::::::::::::~:::::::::::::::::::::::~::::::::::::::::::::;:::::::::::::::::~::::::::::::::::::::::::::: I 
Panther 306 TRILLIUM < 
Page F-16 
Telephone 
Systems 
::::::::::::~::::::::::::::=:::::::::::::::-~:::~~::::::::::::::::::::::::::::::::::::::::::::::::::::::::::~::::::::::~:~:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::~~:::::::::::::::::::::::::::  
						

							. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . 
. . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . ..::::::::::::::::::::::::::::::::::::~::::::::::~:::::::::::~:::::::~::::::::::::::::::::::::::~::::::::::::::::::::~:::::::::::::::::::::~::::~~;:::~::::::::::::::~;::::::~:~~:::::::::~::;::::::~:::::::: 
Technical 
Service Feature 
Manual Programming 
/ i : :::::::::::::::..................................................................................... _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....................... _ ......_.... __ ..... _ _....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .............................................,................. - .......... _ ....... __ ......, 
Manual/Auto Select (program code 0001, prepro- 
grammed for auto intercom) - determines whether an 
intercom or external line is selected automatically wh^en the 
handset is lifted or whether the selection must be made man- 
ually when the handset is lifted. 
NOTE 
Night transfer ringing should be assigned to at 
least one station. 
Night Transfer Ringing (program code 4YY0, prepro- 
grammed for no transfer) - assigns ringing to all lines at 
the indicated station after business hours, and to the loud 
bell contacts when night bell is selected under Loud Bell. 
Pause on Number (program code 0020, preprogrammed 
for no pause) - sets the system for a pause after a specific 
number or numbers are dialed as the first digit. This feature 
is used behind a PBX to allow for a second dial tone. 
Pause Time (program code 0050. preprogrammed for 3 
seconds) - sets length of pause for the Pause on 
N urn b e 
r feature and for a pause inserted by the 
Conference key when programming a speed call 
number. 
Pulse Rate (program code 0010, preprogrammed for 10 
pulses per second) - sets the speed at which 
pulses are 
transmitted (see also Tone 
or Pulse). 
Ringing Assignment (program code 2YY0, prepro- 
grammed for no ringing, except station 10 which is 
preprogrammed to ring on all lines) - chooses which line 
or lines ring at which station or stations. When the optional 
Door Answer Unit is installed, line 3 must be programmed 
to ring at one or more stations. 
Telephone or PBX Line (program code 5Xx0, prepro- 
grammed for telephone line) - tells the XSU which lines 
are central office (CO) lines and which are PBX/CENTFEX 
lines. 
Tone Duration (program code 0011, preprogrammed for 
100 milliseconds) - sets the length of each tone digit dialed 
(see also Tone or Pulse). 
Tone 
or Pulse (program code 5Xx0, preprogrammed for 
tone) - selects tone or pulse signalling for each CO line. 
Zone Paging (program code 3YY 1, preprogrammed for no 
zones) - places stations into specific zones for receiving 
zone paging announcements. Zone paging announcements 
are heard only at stations assigned to a designated zone. 
A 
station can be assigned to no more than one zone. 
I 
TRILLIUM 
Telephone 
Systems 
Panther 306 
Page F-17