Troy-Bilt 675 Hp Manual

							21
Notes   
						

							22
ProblemCauseRemedy
Engine Fails to start1. Blade control disengaged.
2. Spark plug boot disconnected.
3.  Fuel tank empty or stale fuel.
4. Engine not primed (if equipped with primer). 
5. Faulty spark plug.
6. Blocked fuel line.
7. Engine flooded. 
8. Fuel valve (if equipped) closed.
9.  Engine not choked (if equipped with choke).
1. Engage blade control.
2. Connect wire to spark boot.
3.  Fill tank with clean, fresh gasoline.
4. Prime engine as instructed in the Operation 
section.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
7. Wait a few minutes to restart, but do not 
prime.
8. Open fuel valve. See engine manual.
9.  Choke engine. See engine manual.
Engine Fails to start with 
electric starter
(Electric Start Units Only)
1. Electric Start Push Key not fully inserted. 
2. Battery not charged.
3.  Circuit breaker tripped.
1. Insert key into starter housing until it snaps 
into place.
2. Charge battery.
3.  Debris may be blocking blade operation. 
Stop engine, remove Electric Start Key, and 
disconnect spark plug boot. Verify grass or 
other debris is not obstructing the blade. 
Carefully clean out debris if necessary. 
Reattach spark plug boot and reinsert key. 
Wait one minute after tripping for circuit 
breaker to automatically self-reset then 
reattempt start.
Engine runs erratic1. Spark plug boot loose.
2. Blocked fuel line or stale fuel. 
3.  Vent in gas cap plugged.
4. Water or dirt in fuel system.
5. Dirty air cleaner.
6. Unit running with CHOKE (if equipped) 
applied.
1. Connect and tighten spark plug boot.
2. Clean fuel line; fill tank with clean, fresh 
gasoline.
3.  Clear vent.
4. Drain fuel tank. Refill with fresh fuel.
5. Refer to engine manual.
6. Push CHOKE knob in.
Engine overheats1. Engine oil level low.
2. Air flow restricted.
1. Fill crankcase with proper oil.
2. Clean area around and on top of engine.
Occasional skips
(hesitates) at
high speed
1. Spark plug gap too close.1. Adjust gap to .030”.
Continued on next page
Troubleshooting8  
						

							23
ProblemCauseRemedy
Idles poorly1. Spark plug fouled, faulty, or gap too wide.
2. Dirty air cleaner.
1. Reset gap to .030” or replace spark plug.
2. Refer to engine manual.
Excessive Vibration1. Cutting blade loose or unbalanced.
2. Bent cutting blade.
1. Tighten blade and adapter. Balance blade.
2. See an authorized service dealer.
Mower will not
mulch grass
1. Wet grass. 
2. Excessively high grass. 
 
3.  Dull blade.
1. Do not mow when grass is wet; wait until 
later to cut.
2. Mow once at a high cutting height, then 
mow again at desired height or make a 
narrower cutting path.
3.  Sharpen or replace blade.
Uneven cut1. Wheels not positioned correctly. 
2. Dull blade.
1. Place front and rear wheels in same height 
position.
2. Sharpen or replace blade.
Mower will not self propel1. Belt not installed properly. 
2. Debris clogging drive operation. 
3.  Damaged or worn belt.
4. Drive control out of adjustment.
1. Check belt for proper pulley installation and 
movement.
2. Stop engine, disconnect spark plug boot,  
and clean out debris.
3.  Inspect and replace belt.
4. Adjust drive control. (See Assembly & Set-up 
sec tion). 
SECTION 8 — TROUBLESHOOTING  
						

							24
ComponentPart Number and Description
BS-594056 Spark Plug (Briggs & Stratton -  exi
                                  Models)
98079-55846 Spark Plug (Honda)
BS-591868  Spark Plug (Briggs & Stratton - 
                                  Quantum Models)
951-14437 Spark Plug (MTD)
  
BS -29 8 0 9 0S† Fuel Filter (Briggs & Stratton)
951-10358A            Fuel Filter (MTD)
16952-Z8B-000  Fuel Filter (Honda)
BS-491588S Air Filter Cartridge (Briggs & Stratton - 
                                  Quantum Models)
BS-493537S† Pre-Cleaner (Briggs & Stratton -  
                                  Quantum Models)
951-10298 Air Cleaner Kit (MTD)
17211-Z8B-901 Air Cleaner Element (Honda)
BS-593260 Air Filter (Briggs & Stratton - exi
                                  Models)
BS-594055† Pre-Cleaner (Briggs & Stratton -  exi
                                  Models)
BS-799585  Fuel Cap (Briggs & Stratton Quantum)
951-14407 Fuel Cap Assembly (MTD)
17620-ZL8-013 Fuel Cap (Honda)
BS -59 4 0 61‡ Fuel Cap (Briggs & Stratton exi Models)
634-05039  Wheel (Front)
634-04660  Wheel (Rear - Low)
634-05063 Wheel (Rear - High)
Phone (800) 828-5500 or (330) 558-7220 to order replacement parts or a complete Parts Manual (have your full model number and 
serial number ready). Parts Manual downloads are also available free of charge at www.troybilt.com
† If Equipped
‡ Not Shown
Replacement Parts9  
						

							25
ComponentPart Number and Description
731-07131  Discharge Chute
942-0741A              Mulching Blade
942-0741-X             Xtreme Mulching Blade
964-04117B          Grass Bag
954 - 04260             Belt
7 2 5 - 0 6121A† Battery Charger
725-04903†           Battery
731- 0 9728†            Push Key
Phone (800) 828-5500 or (330) 558-7220 to order replacement parts or a complete Parts Manual (have your full model number and 
serial number ready). Parts Manual downloads are also available free of charge at www.troybilt.com
† If Equipped 
SECTION 9 — REPLACEMENT PARTS   
						

							26
ComponentModel Number and Description
490-850-0005      Blade Removal Tool —
 Holds blade in place for faster, safer 
removal.
SPW-134 Spark Plug Wrench —
 Duel ended wrench to serve multiple 
uses. Fits ¾” or 13⁄16” hex plug.   
    
490-850-0008 Oil Siphon —
 Makes it easy to transfer gas, oil and 
liquids from tank to container.
490-850-0016 Side Discharge Blower —
 Blows leaves, grass clippings and 
debris. Eliminates need for separate 
blower. Easy installation with no tools.
490-850-0015 Cargo Carrier —
  Conveniently holds drinks, tools and 
more. Simple installation. Attaches in 
less than two minutes with no tools.
490-241-0034 Garage Floor Mat —
 Anti-skid mat, measures 24” x 36”. 
Projects garage floor form stains.
490-850-0012 Mower Kick Stand —
 Keeps mower stable for changing/
sharpening blade and cleaning 
underside of deck.
Phone (800) 800-7310 or (330) 220-4683 to order attachments and accessories. Have your mower’s full model number and serial 
number ready to assure compatibility. Items can also be purchased online at www.troybilt.com.
Attachments & Accessories10  
						

							27
ComponentModel Number and Description
22216 STA-BIL® fuel Stabilizer,  32 oz —
 Treats 80 gallons of fuel. Keeps stored 
fuel fresh for quick, easy starts. 
Prevents corrosion from moisture and 
ethanol-induced attraction. Prevents 
gum and varnish.
490-290-0012 Mower Cover —
 Protects your mower against sun, rain 
and dust damage. Coated for maximum 
water resistance and repellency. U.V. 
and milddew resistant
490-900-0062 Non-Stick Mower Deck Spray —
 Long-Lasting anti-stick graphite spray. 
Prevents grass clippings buildup in 
mowing deck.
Phone (800) 800-7310 or (330) 220-4683 to order attachments and accessories. Have your mower’s full model number and serial 
number ready to assure compatibility. Items can also be purchased online at www.troybilt.com. 
SECTION 10 — ATTACHMENT S & ACCESSORIE S  
						

							MANUFACTURER’S LIMITED WARRANTY FOR
GDOC-100020 REV. A
The limited warranty set forth below is given by Troy-Bilt LLC with 
respect to new merchandise purchased and used in the United States 
and/or its territories and possessions, and by MTD Products Limited 
with respect to new merchandise purchased and used in Canada and/
or its territories and possessions (either entity respectively, “Troy-Bilt”).
This warranty is in addition to any applicable emissions warranty 
provided with your product.
“Troy-Bilt” warrants this product (excluding its Normal Wear Parts 
and Attachments as described below) against defects in material and 
workmanship for a period of two (2) years commencing on the date of 
original purchase and will, at its option, repair or replace, free of charge, 
any part found to be defective in materials or workmanship. This 
limited warranty shall only apply if this product has been operated and 
maintained in accordance with the Operator’s Manual furnished with 
the product, and has not been subject to misuse, abuse, commercial 
use, neglect, accident, improper maintenance, alteration, vandalism, 
theft, fire, water, or damage because of other peril or natural disaster. 
Damage resulting from the installation or use of any part, accessory 
or attachment not approved by Troy-Bilt for use with the product(s) 
covered by this manual will void your warranty as to any resulting 
damage.
Normal Wear Parts are warranted to be free from defects in material 
and workmanship for a period of thirty (30) days from the date of 
purchase. Normal wear parts include, but are not limited to items such 
as: batteries, belts, blades, blade adapters, tines, grass bags, wheels, 
rider deck wheels, seats, snow thrower skid shoes, friction wheels, 
shave plates, auger spiral rubber and tires.
Attachments — Troy-Bilt warrants attachments for this product against 
defects in material and workmanship for a period of one (1) year, 
commencing on the date of the attachment’s original purchase or 
lease. Attachments include, but are not limited to items such as:  grass 
collectors and mulch kits.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH 
PROOF OF PURCHASE, through your local authorized service dealer. To 
locate the dealer in your area:
In the U.S.A.
Check your Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131, 
Cleveland, Ohio 44136-0019, or call 1-866-840-6483,  
1-330-558-7220 or log on to our Web site at www.troybilt.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-
668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following cases:
a. The engine or component parts thereof. These items may 
carry a separate manufacturer’s warranty. Refer to applicable 
manufacturer’s warranty for terms and conditions.
b. Log splitter pumps, valves, and cylinders have a separate one- 
year warranty.
c. Routine maintenance items such as lubricants, filters, blade 
sharpening, tune-ups, brake adjustments, clutch adjustments, 
deck adjustments, and normal deterioration of the exterior finish 
due to use or exposure.
d. Service completed by someone other than an authorized service 
dealer.
e. Troy-Bilt does not extend any warranty for products sold or 
exported outside of the United States and/or Canada, and their 
respective possessions and territories, except those sold through 
Troy-Bilt’s authorized channels of export distribution.
f. Replacement parts that are not genuine Troy-Bilt parts.
g. Transportation charges and service calls.
h. Troy-Bilt does not warrant this product for commercial use.
No implied warranty, including any implied warranty of 
merchantability or fitness for a particular purpose, applies 
after the applicable period of express written warranty above 
as to the parts as identified. No other express warranty, 
whether written or oral, except as mentioned above, given by 
any person or entity, including a dealer or retailer, with respect 
to any product, shall bind Troy-Bilt. During the period of the 
warranty, the exclusive remedy is repair or replacement of the 
product as set forth above.
The provisions as set forth in this warranty provide the sole 
and exclusive remedy arising from the sale. Troy-Bilt shall 
not be liable for incidental or consequential loss or damage 
including, without limitation, expenses incurred for substitute 
or replacement lawn care services or for rental expenses to 
temporarily replace a warranted product.
Some states do not allow the exclusion or limitation of incidental 
or consequential damages, or limitations on how long an implied 
warranty lasts, so the above exclusions or limitations may not apply to 
you.
In no event shall recovery of any kind be greater than the amount of 
the purchase price of the product sold. Alteration of safety features 
of the product shall void this warranty. You assume the risk and 
liability for loss, damage, or injury to you and your property and/or to 
others and their property arising out of the misuse or inability to use 
the product.
This limited warranty shall not extend to anyone other than the original 
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY:  This limited 
warranty gives you specific legal rights, and you may also have other 
rights which vary from state to state.
IMPORTANT:  Owner must present Original Proof of Purchase to 
obtain warranty coverage.
Troy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-7220 
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238  
						

							Impreso en Estados Unidos de América
MaN ual del operador
Medidas importantes de seguridad • Configuración • Funcionamiento •  Mantenimiento • Servicio •  
Solución de problemas •  Garantía
 ADVERTENCIA
LEA Y SIGA TODAS LAS INSTRUCCIONES DE ESTE MANUAL ANTES DE PONER EN 
FUNCIONAMIENTO ESTA MÁQUINA. 
SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES.
Formulario No. 769-10198
(Octubre 16, 2014)
Podadora tipo abonadora autopropulsada — Modelos TB 220,  
TB 230, TB 240, y TB 280 ES
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019   
						

							2
Gracias por comprar una máquina quitanieve fabricada por Troy-Bilt.  La misma ha sido diseñada cuidadosamente para brindar excelente rendimiento si se la opera y mantiene correctamente. 
Por favor lea todo este manual antes de operar el equipo.  Le indica cómo configurar, operar y mantener la máquina con seguridad y fácilmente.  Por favor asegúrese de seguir cuidadosamente y en todo momento las prácticas de seguridad recomendadas, y hacérselas seguir a cualquier otra persona que opere la máquina.  En caso de no hacerlo podrían producirse lesiones personales o daños materiales. 
Toda la información contenida en este manual hace referencia a la más reciente información de producto disponible en el momento de la impresión.  Revise el manual frecuentemente para familiarizarse con la unidad, sus características y funcionamiento.  Por favor tenga en cuenta que este Manual del Operador puede cubrir una gama de especificaciones de productos de diferentes modelos. Las características y funciones incluidas y/o ilustradas en este manual pueden no ser aplicables a todos los modelos. Troy-Bilt se reserva el derecho de modificar las especificaciones de los productos, los diseños y el equipo estándar sin previo aviso y sin generar responsabilidad por obligaciones de ningún tipo.
En su caso, los datos de prueba de potencia utilizados para establecer la máxima potencia equipado en esta máquina se pueden encontrar en www.opei.org o sitio web del fabricante del motor. 
Si tiene algún problema o duda respecto a la unidad, llame a un distribuidor de servicio Troy-Bilt autorizado o póngase en contacto directamente con nosotros.  Los números de teléfono, dirección del sitio web y dirección postal de la Asistencia al Cliente de Troy-Bilt se encuentran en esta página. Queremos garantizar su entera satisfacción en todo momento.
En este manual, las referencias al lado derecho o izquierdo de la máquina se observan desde la posición del operador.
El fabricante del motor es el responsable de todas las cuestiones relacionadas con el rendimiento, potencia de salida, especificaciones, garantía y mantenimiento del motor. Para obtener mayor información consulte el Manual del Propietario / Operador entregado por el fabricante del motor, que se envía, en 
un paquete por separado, junto con su unidad.
Gracias
Importante Medidas importantes de seguridad..3
Ensamblado y Configuración .................................9
Controles y Características ....................................13
Funcionamiento .....................................................14
Mantenimiento y Ajustes .......................................16
Servicio ....................................................................18
Solución de Problemas .........................................22
Piezas de Reemplazo .................24 (Manual Inglés)
Índice
Nú M ero de Modelo
NúM ero de Serie
registro de informaci