Vidikron Projector Vision Model 100 User Manual

Vidikron Vision Model 100 Owner’s Operating Manual 1-1 
1.1 
About This Manual
This Owner’s Manual describes how to install, set up and operate the Vidikron Vision 100 DLP 
Projector. Throughout this manual, the Vidikron Vision 100 DLP Projector is referred to simply 
as the “Vision 100.” 
Target AudienceVidikron has prepared this manual to help home theater installers and end users get the 
most out of the Vision 100. 
Vidikron has made every effort to ensure that this manual is accurate as of the date...

Introduction
1-2 Vidikron Vision Model 100 Owner’s Operating Manual
Graphic Conventions: These symbols appear in numerous places throughout the manual, 
to emphasize points that you must keep in mind to avoid problems with your equipment or 
injury: 
1.2 
Using This Manual
Use the following table to locate the specific information you need in this manual. 
TIPS highlight time-saving short cuts and helpful guidelines for using 
certain features. 
NOTES emphasize text with unusual importance or special...

Introduction
Vidikron Vision Model 100 Owner’s Operating Manual 1-3 
1.3 
Description, Features and 
Benefits
The Vidikron Vision 100 Digital Light Processing (DLP™) Projector has been specifically 
engineered to produce high performance video in the kinds of environments most people 
use to enjoy their entertainment. Most high-end video projectors are intended for use in 
dedicated home theater environments with controlled lighting. However, many people 
prefer to have their entertainment systems in the...

Introduction
1-4 Vidikron Vision Model 100 Owner’s Operating Manual
Parts List Your Vision 100 is shipped with the following items. If any items are missing or damaged, 
please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON. 
 Vision 100 DLP Projector
Remote Control Unit and two (2), AAA-size batteries 
 AC Power Cord
 Warranty information and registration card
 Vidikron Vision Model 100 Owner’s Operating Manual (this document) 
Optional Accessories: 
 CineWide™ with...

Vidikron Vision Model 100 Owner’s Operating Manual 2-1 
2.1 
Vision 100 at a GlanceFigure 2-1 shows the key Vision 100 components. 
Figure 2-1. Vision 100 Front/Bottom/Side View
1. EXHAUST VENT
2.CABLE OPENING 
Pass cables through this opening.
3. LENS
4. INTAKE VENT
5. IR SENSOR
6. VIDIKRON LOGO
2Controls and Functions
65 34122 

Controls and Functions
2-2 Vidikron Vision Model 100 Owner’s Operating Manual
2.2 
Vision 100 Rear Panel
Figure 2-2 shows the Vision 100 rear panel. 
Figure 2-2. Vision 100 Rear Panel
1.DVI 1 / DVI 2 (Digital) 
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner with 
a DVI or HDMI output.
2.COMPONENT VIDEO (RCA connectors) 
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for 
component video from sources such as DVD players.
3.HD1 / HD2 (Analog BNC...

Controls and Functions
Vidikron Vision Model 100 Owner’s Operating Manual 2-3 
5.12-VOLT (800 mA) TRIGGER OUTPUTS  
Connection for up to three (3), 12-volt trigger-controlled devices. These can be 
retractable screens, screen masks or the Vidikron CineWide with AutoScope system. 
6.S-VIDEO 1 / S-VIDEO 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
7.IR 
Wired input from an external remote control. 
8.RS-232 CONTROL PORT 
A female, 9-pin D-sub...

Controls and Functions
2-4 Vidikron Vision Model 100 Owner’s Operating Manual
17.POWER BUTTON 
Press once to turn on the Vision 100. Press it again to put it into Standby mode. For a 
discrete on or off command, you can use the direct access buttons on the remote 
control.
18.POWER INPUT (100 to 240 VAC) 
Connect the Vision 100 to power here. 
19.MAIN POWER SWITCH 
Disconnects or applies power to the Vision 100.
20.POWER/STANDBY LED 
2.3 
Vision 100 Remote Control
Figure 2-3 shows the Vision 100 remote...

Controls and Functions
Vidikron Vision Model 100 Owner’s Operating Manual 2-5 
1.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2.LIGHT  
Press to illuminate the buttons. 
3.ON / OFF 
Press to turn the projector on or off.
4.CODE 
For Service use only.
5.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display patterns. 
 
When no menus are present on-screen, the UP and DOWN buttons toggle through the...

Controls and Functions
2-6 Vidikron Vision Model 100 Owner’s Operating Manual
Input Selection Buttons: Use these buttons to select an input source directly or to enter 
numeric characters, as follows. 
12.VIDEO (1) 
Press to select Composite video input as the source. 
13.S-VID 1 (2)/ S-VID 2 (5) (S-Video) 
Press to select an S-Video input. 
14.COMP (Component) (3)  
Press to select Component SD (480i/576i) video input as the source. 
15.HD 1 (4) / HD 2 (7)  
Press to select a HD (RGBHV or YPbPr...