Vidikron Projector Vision Model 12 User Manual

Controls and Functions
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 11 
PREL
IMINARY
9. Not used.
10.LIGHT  
Press this button to illuminate the buttons. 
11.CUST 
Press to recall settings for the current input from the “Custom” memory preset. 
12.ISF NIGHT  
Press to recall settings for the current input from the “ISF Night” memory preset. 
13.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display patterns.
14.EXIT 
Press this button to exit...

Controls and Functions
12 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Notes: 

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 13 
PREL
IMINARY
3.1 
Remote Control
To install batteries in the remote control: 
1. Press down the tab on the cover and 
pull the cover in the direction of the 
arrow.
 
 
 
2. Insert the included batteries. Ensure that 
the polarities correctly match the 
 
and  markings inside the battery 
compartment. 
3. Insert the lower tab of the cover into the 
opening, and press down the cover until 
it clicks in place.
Notes on Batteries When...

Installation
14 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Notes on Remote Control 
Operation
The remote control can be used to control the projector within the ranges shown in Figure 
3-1. 
Figure 3-1. Available Range of the Remote Control
 For best results, hold the remote control within 23 feet (7m) of the back or top sensor and 
aligned within 30°.
 Do not drop the remote control or expose it to moisture or high temperature.
 The remote control may malfunction under a...

Installation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 15 
PREL
IMINARY
3.2 
Quick Setup
Table 3-1 gives a quick overview of the Vision 10/12 installation process. The sections 
following this one provide detailed instructions.
Installation should be performed by a qualified custom video installation 
specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, refer to 
page...
1Choose a location for the projector16
2Connect signal sources to the projector22
3Connect external...

Installation
16 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
3.3 
Installation Considerations
Proper installation of your projector will ensure the quality of your display. Whether you are 
installing a projector temporarily or permanently, you should take the following into account 
to ensure your projector performs optimally.
Installation Type Choose the installation type that best suits your needs: front or rear screen, floor mount or 
inverted mount. 
Table 3-2 compares...

Installation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 17 
PREL
IMINARY
Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. This is 
an important calculation in any projector installation as it determines whether or not you 
have enough room to install your projector with a desired screen size and if your image will 
be the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and...

Installation
18 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Vertical and Horizontal 
Position
Proper placement of the projector relative to the screen will yield a rectangular, 
perfectly-centered image that completely fills the screen. 
Ideally, the projector should be positioned perpendicular to the screen and in such a way 
that the lens center and screen center are aligned with each other, as shown in 
Figure 3-3.
Figure 3-3. Projector Placement
Vertical and Horizontal...

Installation
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 19 
PREL
IMINARYFigure 3-5. Horizontal Lens Shift
0%Screen Center
100% Width Lens Shift
(1.0 x W)
50% Width Lens Shift 
(0.5 x W) 150% Width Lens Shift
(1.5 x W)
Screen Width (W)
Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used 
in this example. 

Installation
20 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual
PREL
IMINARY
Table 3-3 gives the lens shift limits for the Vision 10 and Vision 12, as percentages and 
absolute measurements with a 96 x 54 inch (1.78:1) screen. 
Adjusting the Projection 
Angle
If the screen is significantly higher or lower than the projector, you can also tilt the projector 
at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. For a 
floor installation, turn the four...