ViewSonic Pj502 Projector User Manual

ViewSonic  PJ5028
Adjusting the projectors elevator
You can use the elevator feet to make adjustments if the surface on which you need to set 
the projector is uneven or if you otherwise need to adjust the angle of projection. The adjust-
ment range of the elevator feet is 0 to 9 degrees.
1. After making sure that the projector is cool adequately, press and hold in the elevator but-
tons while holding the projector.
The elevator buttons and the elevator feet are on the both sides.
2. Raise or lower the...

ViewSonic  PJ5029
About the filter cover for a unit installed bottom side up
When the projector is installed bottom up, please use the accessory filter cover for bottom-
up use. It is higher than usual filter cover, to keep the space for intake ventilation. Please 
change in the following procedure.
1. After making sure that the projector is adequately cool, carefully turn over the projector 
over so the bottom is facing up.
2. While sliding it in the direction of the arrow and removing, put a finger on...

ViewSonic  PJ50210
Connecting your devices
NOTE . Whenever attempting to connect a laptop computer to the projector, be sure to acti-
vate the laptops RGB external image output (set the laptop to CRT display or to simulta-
neous LCD and CRT display). For details on how this is done, please refer to the instruction 
manual of the corresponding laptop computer.
o Secure the screws on the connectors and tighten.
o Some computers may have multiple display screen modes. Use of some of these modes 
will not be...

ViewSonic  PJ50211
With a computer
AUDIO
Stereo mini audio cable RGB out
RS-232C cable  RS-232C 
RGB cable
Vith a VCR/DVD player
AUDIO Video out
Stereo mini audio cableVideo cable
AUDIO
S-Video out
Stereo mini audio cable S-Video cable 
AUDIO
CB/PB
Stereo mini audio cable Component video cable   Y
CR/PR
Component video out  

ViewSonic  PJ50212
Connecting power supply
1. Connect the connector of the power cord to the AC inlet of the projector.
2. Firmly plug the power cords plug into the outlet. WARNING
X Please use extra caution when connecting the power cord as incorrect or faulty con-
nections may result in fire and/or electrical shock.
* Only use the power cord that came with the projector. If it is damaged, contact your 
dealer to newly get correct one.
* Only plug the power cord into an outlet rated for use with the...

ViewSonic  PJ50213
Remote control
Putting Batteries
1. Remove the battery cover.
Slide back and remove the battery cover in the direction of the arrow.
2. Insert the batteries.
Align and insert the two AA batteries according to their plus and minus terminals as indi-
cated in the remote control.
3. Close the battery cover.
Replace the battery cover in the direction of the arrow and snap it back into place. WARNING
X Always handle the batteries with care and use them only as directed. Improper use 
may...

ViewSonic  PJ50214
Operating the remote control
The remote control works with the projectors remote sensor.
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left 
and right of the remote sensor).
• Also a remote signal reflected in the screen etc. may be available. If it is difficult to send a 
remote signal to the sensor directly, please try.
• Since the remote control uses infrared light to send signals to the projector (Class1 LED), 
be sure to use the remote...

ViewSonic  PJ50215
Power on/off
NOTE. Turn the power on/off in right order. Please power on the projector before the
connected devices. Power off the projector after the connected devices
Turning on the power
1. Make sure that the power cord is firmly and correctly connected to the projector and outlet.
2. Remove the lens cover, and set the power switch to the ON position.
The power indicator will light to solid orange. Then wait several seconds because buttons 
may not function for these several...

ViewSonic  PJ50216
Operating
Adjusting the volume
1. Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting the volume.
2. Use the menu cursor buttons S/T to adjust the volume.
To close the dialog and complete the operation, press the VOLUME button again.
Even if you dont do anything, the dialog will automatically disappear after a few seconds.
Temporarily muting the sound
1. Press the MUTE button on the remote control.
A dialog will appear on the screen...

ViewSonic  PJ50217
Searching an input signal
1. Press the SEARCH button on the remote control.
The projector will begin to check its input ports in order to find any input signals. Then 
when an input is found, the projector will stop searching and display the image. If no sig-
nal is found, the projector will return to the state selected before the operation.
RGB B COMPONENT VIDEO B S-VIDEO B VIDEO