ViewSonic Pj510 Projector User Manual

ViewSonic  PJ5108
Connecting Your Devices
NOTE:
About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by 
connecting this projector to computers that are VESA DDC (display data channel) compatible. 
Please take advantage of this function by connecting the accessory RGB cable to the RGB port 
(DDC 1/2B compatible). Plug-and-Play may not work properly if any other type of connection is 
attempted.
• Plug-and-Play is a system composed of the...

9ViewSonic  PJ510
Please refer to the following for connecting your devices.
See the rear of the projector. You can see the ports.
Connecting to a computer
RGB outRGB cable (D-sub 15 pin)
Audio outAudio cable (Stereo mini)
RS-232C portRS-232C Cable
If using a SCART RGB input,
Video
Audio out (L)
Audio out (R)
SCARTSCART cable
G out out port
B out
R out
RS-232C port
RS-232C Cable
Connecting to a DVD/VCR player
Video out
Audio out (L)
Audio/Video Cable
Audio out (R)
If using a S-video input,
S-video out...

ViewSonic  PJ51010
Connecting Power Supply
1Connect the connector of the power cord to the AC inlet of the projector. 
2Firmly plug the power cord’s plug into the outlet.
 WA R N I N G
• Please use extra caution when connecting the power cord as incorrect or faulty connections may 
result in FIRE and/or ELECTRICAL SHOCK. Please adhere to the “PJ510 UG – Safety Guide” 
and the following.
• Only plug the power cord into outlets rated for use with the power cord’s specified voltage 
range.
• Only use the...

11ViewSonic  PJ510
Remote Control
Putting Batteries
1Remove the battery cover. 
Slide back and remove the cover in the direction of the arrow.
2Insert the batteries.
Align and insert the two AA batteries according to their plus and minus 
terminals (as indicated in the remote control.).
3Close the battery cover. 
Replace the cover in the direction of the arrow and snap it back into place.
 CAUTION
Always handle the batteries with care and use them only as directed. Improper use may result in 
battery...

ViewSonic  PJ51012
Operating The Remote Control
• The remote control works with the projector’s remote sensor.
• The range of the remote sensor is 3 meters with a 60-degree 
range (30 degrees to the left and right of the remote sensor). 
Also a remote signal reflected in the screen etc. may be 
available. If it is difficult to send a remote signal to the sensor 
directly, please try.
• Since the remote control uses infrared light to send signals to 
the projector (Class1 LED), be sure to use the remote...

13ViewSonic  PJ510
Power ON/OFF
Turning On The Power
NOTE:
Turn the power on/off in right order. Please power on the projector before the connected devices. 
Power off the projector after the connected devices.
1Make sure that the power cord is firmly and correctly 
connected to the projector and outlet.
2When the lens cap is attached, remove the lens cap.
3Set the power switch to [ | ] (ON). 
 
Power switch (ON position)
The POWER indicator will light orange.
4Press the STANDBY/ON button 
of the...

ViewSonic  PJ51014
Selecting An Input Signal
1Using the projector’s control button
Press the INPUT button.
As illustrated below, each time you press the INPUT button, the 
projector switches between its input signal ports. Select the signal 
you wish to project.
Selecting a RGB signal, using the remote control
Press the RGB button.
When this button is pressed, the projector switches to the RGB 
port.
Selecting a video signal, using the remote control
Press the VIDEO button.
As illustrated below, each...

15ViewSonic  PJ510
Turning Off The Power
NOTE:
Turn the power on/off in right order. Please power on the projector before the connected devices. 
Power off the projector after the connected devices.
1Press the STANDBY/ON button of the projector or the 
remote control. 
The message “Power off?” will appear on the screen for 
approximately 5 seconds.
2Press the STANDBY/ON button again while “Power off?” 
the message is visible.
The projector lamp will go off, and the POWER indicator 
will begin blinking...

ViewSonic  PJ51016
Operating
Adjusting The Volume
1Press the VOLUME button.
As illustrated on the right, a dialog box will appear on the 
screen to aid you in adjusting the volume.
2Use the (S), (T) buttons to adjust the volume.
Press the VOLUME button again to close the dialog box and 
complete this operation.
(Even if you dont do anything, the dialog box will 
automatically disappear after a few seconds.)
(S) Press this to increase the volume
(T) Press this to decrease the volume
Temporarily Muting The...

17ViewSonic  PJ510
Adjusting The Position
1Press the POSITION button.
As illustrated on the right, a dialog box will 
appear on the screen to aid you in adjusting the 
position.
2Use the (W), (X), (S), (T) buttons to adjust 
the position.
When you want to initialize the position, press 
the RESET button during adjustment.
Press the POSITION button again to close the 
dialog box and complete this operation.  (Even 
if you dont do anything, the dialog box will 
automatically disappear after a few...