ViewSonic Pjd6211 Projector User Manual

							 EN-8
Rear View 
Connection ports
AC power socket
Kensington lock
Rear IR remote control sensor
Ventilation holes (exhaust)
Security bar
Bottom View
Ceiling mount (M4*6)
Tilt-adjustment feet
13245
6
1223456
2
1
122
„This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
„Contact your dealer for information to mount the projector on a ceiling. 
						

							EN-9
Using the Product
Control Panel
LED
Button Function
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
 /Keystone
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
ENTER
Enter to sub-menu and confirm the menu selection.
SOURCE
Manually select an input source.
MENU/EXIT
Display or exit the on-screen display menus.
Power
Turn the projector on or off.
13
4
6
7
5
4
2
8
9
1
2
3
4
5
6
7
8
9 
						

							 EN-10
Connection Ports
USBThis connector is for firmware update.
VIDEO
Connect composite video output from video equipment to this jack.
S-VIDEO
Connect S-Video output from video equipment to this jack.
MONITOR OUT
Connect to a computer display, etc.
COMPUTER IN 1Connect image input signal (analog RGB or component) to this jack.
RS-232When operating the projector via a computer, connect this to the controlling computers
RS-232C port.
COMPUTER IN 2Connect image input signal (analog RGB or component) to this jack
12V OUT12V DC out
AUDIO INConnect an audio output from video equipment to this jack.
AUDIO OUTConnect to a speaker or other audio input equipment.
13456789102
1
2
3
4
5
6
7
8
9
10 
						

							EN-11
Remote Control
POWER
Turn the projector on or off.
Four directional buttons
Use four directional buttons to
select items or make adjustments
to your selection.
MENU
Display or exit the on-screen display
menus.
Resync
Resynchronize the projector to the
input signal from a computer.
Source
Manually select an input source.
Aspect
Choose your desired aspect ratio.
Blank
Cut off the screen temporarily. 
Press again to cancel the blank 
function.Keystone+ / -
Adjust image distortion caused by
tilting the projector.
ViewMatch
Switch in between high brightness
performance or Accuracy color
performance Freeze
Press freeze to pause the screen 
image. Press again to cancel the freeze 
function.
1
2
3
4
5
6
79
810 
						

							 EN-12
Replacing the Battery
For the first time use:
Remove the transparent insulation tape by pulling
it before use.
For battery change:
1. Push the catch to the left and remove the battery 
holder.
2. Remove the old Lithium coin cell and install new one
(CR2025). Ensure that the side with the mark “+” is up.
3. Push the battery holder back into the remote control 
until you feel a click.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.„ Dispose of used batteries according to the instructions.„ Make sure the plus and minus terminals are correctly aligned when loading a battery.
„Keep the battery out of the reach of children. „Do not recharge the battery or expose the battery to fire or water.„Do not dispose the used battery along with household waste. Dispose ubatteries according to local regulations.„Danger of explosion may happen if batteries are incorrectly replaced. 
Replace only with the same type recommended by the manufacturer.
„Battery should not be in or near to fire or water, keep batteries in a darkand dry place. „If suspect battery leakage, wipe out the leakage and then replace a new bat
the leakage adheres to your body or clothes, rinse well with water immediat 
						

							EN-13
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from
the front
„Operating the projector from 
the rear
1015
7m
5m
5m
1015
7m5m
5m
„The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations with excessively high temperature or
humidity.
„Do not get water on the remote control or place wet objects on it.„Do not disassemble the remote control. 
						

							 EN-14
Installation
Connecting the Projector
USB Cable VGA (D-Sub) to HDTV (RCA) Cable
VGA Cable (D-Sub to D-Sub) Composite Video Cable
RS-232 Cable S-Video Cable
Audio Cable15
26
37
4
22214
Desktop type Laptop type
3
55467
4
„When connecting cable, power cords of both projector and external equipment 
should be disconnected from AC outlet.
„The figure above is a sample connection. This does not mean that all of these 
devices can or must be connected simultaneously.
„The cables that come with the projector may differ from the above illustration. 
The included cables are based on actual shipment delivery. 
						

							EN-15
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   button on the control panel or the 
POWER button on the remote 
control to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
„If you are connecting multiple sources to the projector simultaneously, press
the SOURCE button on the control panel or the Source button on the remote
control.
Warning
„Remove the lens cap first before powering on.
„Never look into the lens when the lamp is on. This can damage your eyes.
„This focal point concentrates high temperature. Do not place any object near
it to avoid possible fire hazard.
Powering Off the Projector:
1. Press   button on the control panel or the POWER button on the remote
control to turn off the projector lamp. You will see a message Power off? Press
Power again appear on the screen.   
2. Press   button on the control panel or the POWER button on the remote 
control again to confirm.
„The cooling fans continue to operate for cooling cycle.
„When the Lamp LED begins flashing, the projector has entered stand-by mode.
„If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-
by mode, simply press   button 
on the control panel or the POWER button
on the remote control
 to restart the projector.3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off. 
						

							 EN-16
Adjusting the Projector
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the 
height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.2. Adjust the image by sliding the zoom ring. 
Elevator button
Elevator foot Tilt-adjustment foot
„To avoid damaging the projector, make sure that the elevator foot and tilt-
adjustment foot are fully retracted before placing the projector in its carrying 
case.
Focus ring Zoom ring 
						

							EN-17
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen size
Diagonal (inch)4 : 3 Screen
Wide Tele
Projection distance Projection distance
minchminch
40 1.57 61.76 1.73 67.93
50 1.96 77.20 2.16 84.92
60 2.35 92.64 2.59 101.90
70 2.75 108.07 3.02 118.88
80 3.14 123.51 3.45 135.86
90 3.53 138.95 3.88 152.85
100 3.92 154.39 4.31 169.83
120 4.71 185.27 5.18 203.80
150 5.88 231.59 6.47 254.75
200 7.84 308.78 8.63 339.66
250 9.80 385.98 10.78 424.58
300 11.76 463.18 12.94 509.49
40 60 100 120 200
Wide: 1.57m Tele: 1.73m
Wide: 2.35m   Tele: 2.59m
Wide: 3.92m Tele: 4.31m
Wide: 4.71m Tele: 5.18m
Wide: 7.84m Tele: 8.63m
„Position the projector in a horizontal position; other positions can cause heat 
build-up and damage to the projector.
„Keep a space of 30 cm or more between the sides of the projector.„Do not use the projector in a smoky environment. Smoke residue may build-
up on critical parts and damage the projector or its performance.„Consult with your dealer for special installation such as suspending from a 
ceiling.