Vivitek D5000 User Manual

							
DLP Projector—User’s Manual 
– 14 – 
Installing the New Lens 
1.  Align the notches and correctly position 
the electrical contact pad as shown in 
the picture. 
Note: 
Pin of IRIS should be in the direction 
as shown in the picture. 
2.  Rotate the lens clockwise until you feel 
it click into place. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 15  – 
Starting and Shutting down the Projector 
1.  Remove the lens cap. 
2.  Securely connect the power cord and 
signal cable. When connected, the 
power led will turn red. 
 
 
3.  Turn on the lamp by pressing 
“
” button on the rear of the pro-
jector or “
” on the remote control. 
The PWR LED will now flash green.  
The startup screen will display in ap-
proximately 30 seconds. The first time 
you use the projector, you can select 
your preferred language from quick 
menu after the startup screen display. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
– 16 – 
4.  If more than one input device is con-
nected, press the 
SOURCE button and 
use  ▲▼  to scroll among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 
 
DVI: DVI 

HDMI: HDMI 

VGA1/ VGA2: Analog RGB 

BNC: Analog / serial digital interface video inputs 

Component Video: DVD input YCbCr / YPbPr, or  HDTV input YPbPr via HD15 connector
 

S-Video: Super video (Y/C separated) 

Composite Video: Traditional composite video 
5.  When the “Power Off? /Press  Power 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
1. Be sure to remove the lens cap before starting projector.  
2. Do not unplug the power cord until the LAMP LED stops flashing–indicating the projector has 
cooled down. 
 
 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 17  – 
Setting an Access Passw ord (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projec-
tor. When enabled, the password must be entered after you power on the projector. (See  Navigating 
the OSD  on page 24 and  Setting the OSD Language  on page 25 for help on using OSD menus.) 
Important: 
Keep the password in a safe place. Without the password, you will not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the MENU button to open the OSD 
menu. 
2.  Press the cursor  ◄► button to move to 
the  Installation I  menu, press the cursor 
▲▼  button to select  Advanced. 
 
 
3.  Press the cursor  ▲▼ button to select  
Security Lock . 
4.  Press the cursor  ◄► button to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
– 18 – 
5.  You can use the cursor buttons  ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
Press the cursor buttons in any order to set 
the password. Push the  MENU button
 to 
exit the  dialog box. 
 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step 5. In case you forget the password, 
please contact the service center.  
The service center will validate the owner 
and help reset the password.  
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 19  – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Remove the Back Foot Holder on the rear  adjuster foot before adjusting the projection  
angle. 
 Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, twist 
the adjusters clockwise. 
 
2.  To lower the level of the projector, lift 
the projector and twist the adjusters 
counter clockwise. 
 
 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
– 20 – 
Adjusting Projected Imag e Position Using Shift 
 
The Shift feature provides a lens shift function that can be used to adjust the position of the projected 
image either horizontally or vertically within the range detailed below. 
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be adjusted between 100% and -20% of half image height. Note that 
the maximum vertical image height adjustment can be li mited by the horizontal image position. For 
example it is not possible to achieve the maximum vertical image position height detailed above if the 
horizontal image position is at maximum. Please consult the Shift Range diagram below for further 
clarification. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 21  – 
Adjusting the horizontal image position 
With the lens in the center position the horizontal image position can be adjusted to the left or right by 
up to a maximum of 10% of the half image width. Note that the maximum horizontal image height ad-
justment can be limited by the vertical image position. For example it is not possible to achieve the 
maximum horizontal image position if the vertical image position is at maximum. Please consult the 
Shift Range diagram below for further clarification. 
 
Shift Range Diagram 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
– 22 – 
Adjusting the Zoom, Foc us and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size. 
 
2.  Use the  Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image. 
 
3.  Use the  KEYSTONE  
buttons (on the projector 
or the remote control) to 
correct image-trapezoid 
(wider top or bottom)  
effect. 
 
Remote control and OSD panel 
4.  The keystone control  
appears on the display.  
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 23  – 
Adjusting the Volume 
1.  Press the  Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  Left or 
Right 
Cursor  buttons on the 
keypad to adjust  Volume 
+/- . 
 
 
 
3.  Press the  MUTE button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
Downloaded From projector-manual.com Vivitek Manuals