Vodavi Infinite Gk-816 Installation Manual

Injinite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMING 
System Parameters Programming (Cont’d) 
730.8 PRESET CALL FORWARD 
Prow Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
first (See Paragraph 700.4). 
To assign a Preset Call Forward position to a 
stauon: 
a. 
b. Dial an asterisk [*I and [33] on the dial pad. 
Press the station button for the station 
being given a Preset Call Forward position. 
LED...

SYSTEM PARAMEXZRS PROGRAMMING Infinite 816 Key Telephone System 
System Parameters Programming (Cont’dl 
730.9 
CONFERENCETIMER 
a .z Steps 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
fkst (See Paragraph 700.4). 
To change the conference timer: 
a. Dial an asterisk [*I and [34] on the dial pad. 
b. Dial a two-digit number between 00 and 
99. An entry of 00 disables the timer. 
c. Press HOLD to enter data Description...

Infinite 8 16 Key Telephone System SYSTEM PARAMEIERS PROGRAMMING 
System Parameters Programming (Cont’dl 
730.10 SMDR ENABLE 
ProgrammPg Steps 
If the system is fn the Programming mode, 
con&me using program codes. If starting to 
program here, enter the Progr amming mode 
first (See Paragraph 700.41. 
To program SMDR 
a Dial an asterisk [*I and 1351 on the dial pad. 
b. Press CO line(s) for which SMDR is to be 
disabled or enabled. 
l LED on = enabled 
l LED off = disabled 
n//////n 
c. Press HOLD to...

SYSTEM PARAMETERS PROGRAMMING Infinite 816 Key Telephone System 
System Parameters Programming (Cont’dl 
730.11 STATION MESSAGE DETAIL RE- 
CORDING (SMDRI 
Progmmming Steps 
To determine what calls are to be recorded, 
baud rate, and print format: 
a. Press the asterisk [*I and dial 1361 on the 
dial pad. 
b. Press desired program button to deter- 
mine if all calls are to be recorded 
or just 
long distance calls. 
l LED off = long distance 
l LEDon =allcalls 
c. Press desired program button to deter-...

Infinite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMING 
System Parameters Programming (Cont’a) 
730.12 DATE/TIME FORMAT 
Programming Steps 
If the system is in the Programmin g mode, 
continue using program codes. If starting to 
program here, enter the Progr amming mode 
first (See Paragraph 700.4). 
To change the format of the LCD display: 
a. Dial an asterisk [*I and [38] on the dial pad. 
b. Press the desired program button to deter- 
mine the date and time display format. 
l LED on = 12 hr,...

SYSTEM PARAMEIXRS PROGRAMMING In$.nite 816 Key Telephone System 
System Parameters Programming 
ICont*dl 
730.13 STATION SPEED DIAL 
Each telephone has 20 unique speed dial num- 
bers. These numbers are entered and stored 
by the user and can be recalled by the user at 
any time. 
To program a station speed number: 
a Lift handset or press on/off button. 
b. Press AUTO/SAVE button twice. 
c. Press sTA/SPD button where number is 
to be stored. 
d. Press outside line button if desired. 
e. Enter telephone...

InfZnite 816 Key Telephone System SYSTEM PARAMETERS PROGRAMMING 
- The asterisk [‘I is used to indicate a 
Pulse-To-Tone switchover. 
- The Pound [#I button to insert a 
Pause command. 
- The ELASH button to program a 
Flash command. 
- The CONF button is used to program 
a “No Display”. 
The [*I can be programmed as a digit. 
e. Press HOLD button. 
To continue programming additf onal numbers, 
repeat from step a. 
730.19 SETTING 
SYSTEM DATE AND 
System date and time can be set only from the 
attendant...

SYSTEM PDRS PROGRAMMING In#nite 816 Key Telephone System 
C. Receiving an Audible Message Wa.iw 
SbPd 
An SLA may receive an audible message wait- 
ing signal in the form of the ‘system wide’ 
Message Wait Reminder Tone. This tone must 
be enabled in the system data base program 
code 25. When message wait reminder tone is 
enabled ALL sta.Uons &I the system will receive 
this alert tone at the programmed interval in- 
cluding SLTs connected to the SYA. Refer to 
System Timers, SecUon 730.2 for complete...

Infinite 826 Key Telephone System EXCEPTION TABLES PROGRAMMING 
SECTION 740 
EXCEPTION TABLES PROGlUiMMING 
740.1 TOLL RESTRICTION TABIES 
fipmdng Steps Description 
If the system is in the Programming mode, 
continue using program codes. If starting to 
program here, enter the Programming mode 
first (See Paragraph 700.4). 
To enter numbers into the toll tables: 
a Dial an aster&k [*I and use one of the 
following: 
b. Allow Table 
A = [41]. Deny Table A = I421 
Allow Table B = [43], Deny Table B= [441...

EXCEPT’XON TABLES PROGRAMMING Inmite 816 Key Telephone System 
Exception Tables Programming (Cont’a) 
Toll Restriction Tables (Cont’d) 
Prow Steps 
Description 
When the Do Not Disturb (DND) button is used, 
it enters a 
don’t care character. This will allow 
or deny any digit 0 to 9 in that location. 
When a CO line is marked PBX, Class of Service 
(COS) restrictions apply to the station only if 
one of four PBX codes are dialed first. 
The Allow/Deny tables are reserved for COS 2 
and 3, respectively....