Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

							STARPLUS @ SPD 4696LEAST COST 
ROUTlNG (LCR) PROGRAMMINGDigital Key Telephone SystemLCR PROGRAMMING 
(Cont’d)
I.Default LCR Database
Programming StepsDescription
In an effort to decrease installation and set up time,
usually associated with LCR, a default LCR data-
base has been incorporated. The default LCR data-
base will provide basic routing for local and long
distance dialing. Default entries have been made in
the 3-Digit Table for local office codes 
(NNX’s) and
all area codes 
(NPA’s). Six routes have been estab-
lished with the default database for routing of all callsunder default. The entire default database’is shown
in Figure 675-8 DB Printout of LCR Default.
665-l 4issue 
1, March 1994 
						

							STARPLUS @ SPD 48%Digital Key Telephone System
TABLE OF CONTENTS FOR SECTION 670
SECTION 670INITIALIZE DATABASE PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .670-l
670.1INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .670-I
A.
6.c.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.Initialize
SystemParameters.........................................................670-2
InitializeCOtineAttributes............................................................670-5
Initialize Station Attributes.............................................................670-6
initialize Station and CO Port Parameters
.....................................670-9
InitializeExceptionTables...........................................................670-l 0
InitializeSystemSpeedNumbers..................................................670-l 1InitializeLCR Tables..
..................................................................670-t 2
Initialize System Database and Reset (all parameters).
..............670-13
Initialize 
ICLID Parameters..........................................................670-l 4
InitializeDirectoryDialing TableParameters...............................670-l 5
InitializeHunt GroupParameters.................................................670-I 6
Initialize ACDor UCDGroup
Parameters.....................................670-l 7
InitializeVMGroup
Parameters...................................................670-l 8
SystemReset..............................................................................670-l 9
Issue 
1, March 1994670-i 
						

							STARPLUS * SPD 4696
Digital Key Telephone SystemINITIALIZE DATABASE PARAMETERS
SECTION 670
INlTiALlZE DATABASE PARAMETERS
670.1INTRODUCTION
Programming Steps
If the system is in the programming mode, continue
using the program codes. If starting to program here,
enter the programming mode. Refer to Sec. 600.2,
Program Mode Entry (Key Station).
If Database Parameters need to be initialized:
1. Press FLASH and dial 
[80]. The following
message will be shown on the display of a
display phone:Description
This section describes the procedures and steps
necessary to initialize the system database returningany programmed data to its original or default value.
The entire system 
database may be initialized or
various portions of the database may be individually
initialized. In addition to initialization of the entire
database, a system reset (Button 
#+20) command is
also included in this section for clearing meantime
errors without initializing the database.
INITIALIZE DATA-BASE
ENTER BUTTON NUMBERThe buttons on the key telephone are defined as
shown below when entering the Initializing Data-Base Parameters programming area:11 a
SvslEu PARAMETERS! 
2J wCOLNAT,R,EUES
1MlN-ToRwpsj It A
1 soCLWTABLESw L :.*Features available with optional software.
issue 1, March 1994670-l 
						

							INlTlALlZE DATABASE PARAMETERS
STARPLUS @ SPD 4896
Digital Key Telephone System
INlT DATABASE PARAMETERS (Cont’d)
A. Initialize System Parameters
Programming Steps
If System Parameters need to be initialized:
1.Press the System Parameters flexible button
(Button 
#l). The following message will be
shown on the display phone:Description
The system parameters may be initialized setting all
data fields to their original, default values. The 
fol-lowing data fields are returned to their default values
upon initializing the System parameters.
2.To initialize the system parameters, press theHOLD button. Confirmation tone is heard.
PROGRAM CODE 
B:+;NFEATUREDEFAULT VALUE
(after initializing)
1  FLASH01
FLASH 05/  1/  System Hold Recallj
060seconds
/
2/  Exclusive Hold Recall,
180 seconds!I
/
3/  Attendant Recall Timer01 minutesI
4 /  Transfer Recall Timer:045 seconds
5/  Preset Forward Timer10 secondsI
I
6Call Forward No AnswerI
015 seconds
7Pause Timer
2 secondsI
81  Call Park Timer180 secondsI
9/  Conference/DISA Timer:10 minutesI
10j  Paging Timeout Timer/15 secondsI
I
111  CO Ring Detect Timer
I300 milliseconds
I
12/  DISA/SLT Receiver Timer/
I020seconds
I
13j  MSG Wait Reminder Tone000 minutes
!
14/  SLT Hook-flash Timer10 (1 seconds)
15/  SLT Hook-flash 
Debounce010 (.l second)I
16j  SMDR Call Qualification Timer30 sec.I
17!  Auto Call Back Timer00 sec. (disabled)
18:  Reminder Ring Timer00 sec. (one burst)
19/  Release Guard Timer300 milliseconds
1I  Attendant OverrideDisabled
2 I
Hold PreferenceSystem HOLD
3/  External Night Ringing
IDisabled
/
4I
Enabled
Ij  Executive Warning Tone
5/  Page Warning ToneEnabled..
6/  Background MusicEnabled
7
/  LCR EnableDisabled
8j  Forced Account CodesI
Disabled
9’  Group ListeningDisabled
10i  Idle Speaker ModeDisabled
11I  Call Cost Display FeatureDisabled
12/  Music On HoldEnabled
131  Handset Receiver GainDisabled
670-2Issue 
i, March 1994 
						

							STARPLUs @ SPD 48%
Digital Key Telephone SystemINlTlALlZE DATABASE PARAMETERS
INIT. DATABASE PARAMETERS (Cont’d)
Initialize System Parameters (Cont’d)
StensProgrammina
PROGRAM 
(
iTf+zr?rintinnALUE 
7FLASH 10
FLASH 11FLASH 12
FLASH 13
FLASH 142incoming Intercom Ringing
120 ipm flutter
3Call Forward
30 ipm flash
4
Message Waiting/
15 ipm flash
!  Attendant AssignmentI
STA 100
l-4!  Time and Date Format
12 HR, M/D/Y
I
i  PBX Dialing Codes
None
I
Ii  ExecYSecy Pair #II
None
I
2I  ExecSecy Pair #2None
j  
Exec/Secy Pair #3I
I3None
I
/
41  
Exec/Secy Pair $4INone
1/  Relay #lNone
I
2I
I
Ii  Relay #2None
3I  Relay #3None
I4:  
Sensor+/1None
51  Sensor #2None
,
6i  Sensor #3None
7I
FLASH 15FLASH 20
FLASH 21/
/
a1  StationsNone
11 jI
I
12’  Relay/Sensor XlNone
13 jRelay/Sensor 
#2NoneI
141  Relay/Sensor #3None
1.5’  Relay/Sensor #4None
1:  Port #l (“On-Board” RS-232C)~
2400!
I
2:  Port 
#2 (“On-Board” Modem)1200/
3I  Port #3 (Backplane RS-232C)2400
I
/
4Port #4 (Backplane RS-232C):
2400
,
1/  DISA Access Code000I
2I  Data Base Admin. Access[DBAMT 3226I
I
1j  SMDR
NO (disabled)
2I  Reported Call Type
:!LD only
/
31  Print Format80 columnI
4j  SMDR Baud Rate2400
5SMDR Reporting Port
Port #lI
I
Issue 1, March 1994
570-3 
						

							INITIALIZE DATABASE PARAMETERSSTARPLUS @ SPD 4996
Digital Key Telephone System
INIT. DATABASE PARAMETERS (Cont’d)
Initialize System Parameters (Cont’d)Programming StepsDescription
/  FLEX
PROGRAM CODE , 
BU7TONFEATUREDEFAULT VALUE
(after initializing)
/  FLASH22I
1Night Mode Operation-ManualFLASH 23
FLASH24
2/ANM Schedule - Mon.
3IANM Schedule - Tues.
41ANM Schedule 
- Wed.
5/ANM Schedule - Thur.
i
6ANM Schedule - Fri.
71ANM Schedule - Sat.
I  ANM Schedule 
- Sun.
!  
I!4 1  Directory Dialing Table
il-l
2!Flexible Card Assignments
08:00/l 7:00
08:00/l 7:00
08:00/l 7:00
08:00/l 7:00
08:00/l 7:00
##:##I##:####
##:##/##:##None
i4Station, 4 CO Line,4
Station
670-4Issue 1, March 1994 
						

							STARPLUS @ SPD 4896
Digital Key Telephone System
INITIALIZE DATABASE PARAMETERS
“7. DATABASE PARAMETERS (Cont’d)
is.Initialize CO Line AttributesProgramming Steps
if CO Line Attributes need to be initialized:
1.Press the CO Line Attributes flexible button
(Button 
#2). The following message will be
shown on the display phone:Description
The CO Line parameters may be initialized setting
all data fields-to their original, default values. The
following data fields are returned to their default
vaiue upon initializing the CO Line parameters.
2.To initialize the CO Line Attributes, press the
HOLD button. Confirmation tone will be
heard.
PROGRAM CODE I  
B:+;N I
FEATUREDEFAULT VALUE
I(after initializing)
FLASH 
4011  DTMF/Pulse SignalingI
ALL Lines set for DTMF
2CO/PBX Marking
ALL Lines set for CO
3 IUniversal Night Answer
Enabled on all Lines
4 ;
DISA TRK-to-TRK (Conf)Enabled on all Lines
I
5/  Automatic PrivacyEnabled on all tines
1
!6/  Loop Supervision
NO (disabled on all lines)
I7 :
DISA Operation
NO (disabled on all lines)
!
I
8j  Flash Time
10 (1 second)
/
9i  Line Group Assignment
All Lines are in Group 1
IOI  Line Class of Service
IAll Lines assigned COSl1
/
11I
I! CO Line Ring Assignment
All Lines Ring at STA 100
II
12/  CO Line Identification
None
/
13:  Trunk Direction
Incoming-Outgoing
I
14/  Ring Delay Timer
00 (disabled)
;  FLASH 41
1’  Dial Pulse Break/Make Ratio60140
Issue 1, 
March 1994s70-5 
						

							INlllALlZE DATABASE PARAMETERS
STARPLUS @ SPD 4896
Digital Key Telephone System
INlT. DATABASE PARAMETERS (Cont’d)
C.Initialize Station Attributes
Programming Steps
If Station Attributes need to be initialized:
1. Press the Station Attributes flexible button
(Button 
#3). The following message will be
shown on the display phone:
2.To initialize the Station Attributes, press the
HOLD button. Confirmation tone will be
heard.Description
The Station parameters may be initialized setting all
data fields to their original, default values. The fol-
lowing data fields are returned to their default value
upon initializing the Station parameters.
PROGRAM CODE /  
B;;;N /
FEATURE
FLASH 50, Page “A”
A/i/  Page Access
Al2j  Do Not Disturb
i  
I2/  Conference
/  Executive Override
I
A/5i  Privacy Release
/  
Ai/  System Speed Dial
1  
Au/  Line Queuing
i  
Al8/  Preferred Line Answer
A/9!  Off-Hook Voice-Over
Al10/  Call Forward
All 1/  Forced LCR
AI12/  ACD* Supervisor Barge-In
All3/  Executive Override Blocking
I  
AI14!  CO Line Ringing Options
FLASH 50, Page 
“8” B/lj  Station ID
/
B/2Station Class of Setvice
B/3i  Speakerphone Option
B/4 1Pick-Up Group(s)
/
B/5j  Paging Zone(s)
B/6j  Preset Forward Destination
I
j
Bf7 !CO Line Group Access!DEFAULT VALUE
(after initializinq)
I
Allowed
Allowed
I
I
Allowed
/
I
Not Allowed
Not Allowed
Allowed
Allowed
Not Allowed
/
Not Allowed
Allowed
Not Allowed
Not Allowed
Allowed at all stations
I
Muted Ringing allowed
!  All Key Stations default to Station
I  ID 0 (keyset), All Single Line
1
/Telephones and 
OPX’s default to
jID 5 (SLT 
w/o MSG Wait)
All Stations assigned COS 1I  All Stations assigned option 1
/  All Stas assigned into Group 1
!  All Stas assigned into Zone 1
I
None assigned
i  All Sta assigned access 
t?J Group
I 1
B,8j  LCR Class of Service
/
B,g i  Off-Hook Preference
j  
B/10 j  Flex Button Assignment
Features available with optional software.1  All Stations given an LCR COS of
i  0
/  Is allowed to all stations with the
j  ability to change the assignment
iSee default button assignment
670-6
Issue 
;, March 1994 
						

							STARPLUS @ SPD 4696
Digital Key Telephone SystemINITIALIZE DATABASE PARAMETERS
-
i;  CAMP ON
LINE QUECALL BACK
PICK UP
MSGFWD
jDND
CONF
____ /I-
,ABC /  DEF !
1!2:‘3’‘-.:/
GHI/  
JKL /  iMN($
4:5:;f:
___ ~ ~
iPRS /TUV/ m
7‘8ii9’HOLD
*
;OPER j  1
#ioij I
HTP- -SPKRVOLFigure 670-l 
34-Button Default Button Mapping
RINQ VOL
Issue 1, March 1994670-7 
						

							INITIALIZE DATABASE PARAMETERSSTARPLUS @ SPD 4896
Digital Key Telephone System:
/
1
-
iMSGco2
LOOPPOOLm
IWDDNDCONF
HOLD
112:;3-TwNS “j&jGHI
4FLASH ia
~ I
PRSITUVI iwxY!SPEED
7/8ji9;MUTE i’:
*ON/OFF ‘Gjf&j
HTP-SPKR VOLRING VOL
Figure 670-2 
i4-Button Default Button Mapping
670-8Issue 1, March 1994