Xerox Projector Dp 1011 User Manual

Xerox DP1011 User’s Guide16
User Controls
Adjust the Projector Image
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the All Images menu and press the Enter button.
The All Images menu appears.
3. Use the     keys to select the item you want, and use the
   keys to adjust the selected setting.
4. When the new settings are what you want, press the Menu 
button again.
Brightness—Lightens or darkens the image. The higher the 
number, the brighter the image....

Xerox DP1011 User’s Guide17
User Controls
Adjust the Computer Image
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the Computer Image menu and press the Enter button.
The Computer Image menu appears.
3. Use the     keys to select the item you want, and use the
   keys to adjust the selected setting.
4. When the new settings are what you want, press the Menu 
button again.
Auto Image—Automatically adjust the frequency, tracking, and 
horizontal and vertical...

Xerox DP1011 User’s Guide18
User Controls
Adjust the Video Image
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the Video Image menu and press the Enter button.
The Video Image menu appears.
3. Use the     keys to select the item you want, and use the
   keys to adjust the selected setting.
4. When the new settings are what you want, press the Menu 
button again.
Color Saturation—Adjusts the video image from black and white 
to fully saturated color. The...

Xerox DP1011 User’s Guide19
User Controls
Projector Management
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the Management menu and press the Enter button.
The Management menu appears.
3. Use the     keys to select the item you want, and use the
   keys to adjust the selected setting.
4. When the new settings are what you want, press the Menu 
button again.
Menu Location—Sets the location of the menus on the screen.
Projection Direction:...

Xerox DP1011 User’s Guide20
User Controls
Adjust the PiP (Picture in Picture)
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the PiP menu and press the Enter button.
The PiP menu appears.
3. Use the     keys to select the item you want, and use the
   keys to adjust the selected setting.
4. When the new settings are what you want, press the Menu 
button again.
PiP—Turns on and off the PiP function.
PiP Location—Sets the position of the PiP screen on the...

Xerox DP1011 User’s Guide21
Maintenance
Maintenance
Changing the Lamp
The projector’s lamp life is approximately 1500 hours of use. The 
projector automatically monitors the lamp life. After 1500 hours of 
use, the projector displays the message:
The Lamp has been in use for over 1500 hours. You should 
purchase a spare bulb.
When you see this message, please contact your local reseller or 
service center to change the lamp as soon as possible.
Warning—To reduce the risk of personal injury, do not drop...

Xerox DP1011 User’s Guide22
Maintenance
4. Remove the cover.
5. Remove the two screws from the lamp module.
6. Lift up the handle and pull out the lamp module.
7. To replace the lamp module, reverse the previous steps.
Lamp Module 

Xerox DP1011 User’s Guide23
Maintenance
Troubleshooting
If you try the troubleshooting procedures described in this section 
and the problem persists, you may have a malfunctioning projector. 
Refer to the technical support card that you received with your 
projector or contact the retailer where you purchased your 
projector. Also visit our web site at www.xeroxprojectors.com for 
additional technical information. 
Problem: No image appears on the screen.
Check for one of these possible problems:
•Are...

Xerox DP1011 User’s Guide24
Maintenance
For Windows 95, 98, 2000, XP:
1. From the Windows Start menu, select Settings/Control Panel 
and then double-click the Display icon.
2. Select the Setting tab. 
The Desktop Area shows the resolution setting. 
3. Verify that the resolution setting is 1024 x 768 or less.
If the projector is still not projecting the whole image, you will also 
need to select another monitor display for your computer. Use the 
following steps.
To select another monitor display:
1. On...

Xerox DP1011 User’s Guide25
Maintenance
Problem: The image is flickering or otherwise unstable
Try one of these possible solutions:
•On the On-screen display, go to the Computer Mode page 
and select Tracking. Change the tracking until the image 
stabilizes.
•Change the color setting of your computer monitor. 
Change the number of colors that your computer displays on its 
monitor.
Problem: Image has vertical flickering bar.
Try one of these possible solutions:
•On the On-screen display, go to the...