Xerox Projector Dp 820 User Manual

User Controls
16Xerox DP 820 User’s Guide
User Controls
Panel Control and Remote Control
Panel Control
Control Description
Power (LED)
Lamp (LED)Indicates status of projector power and lamp. 
See “LED Indicators” on page 13 for details.
 PowerTurns projector power on and off. See 
“Powering On/Off the Projector” on page 11 for 
the specific power on/off sequences.
Menu/EnterPress to display and activate the OSD menu. If 
the menus are displayed, confirms your 
selection of items on the menus. 
Keystone (...

Xerox DP 820 User’s Guide17
User Controls
Remote Control
Laser Beam Pointer
Button Description
 PowerTurns projector power on and off.
 (Enter)When the OSD menus are displayed, selects 
OSD option.
Directional Selection 
Buttons 
(     )When the OSD menus are displayed, scrolls 
through menus and selects items or adjusts 
settings.
MenuPress to display the OSD menus. Press again 
to exit the OSD menus. 
LaserPress to activate a laser beam for use as a 
pointer. Warning—Do not look into the laser 
beam or...

User Controls
18Xerox DP 820 User’s Guide
Remote Control Operation
The infrared emitter is at the top of the remote control next to the 
laser pointer. The infrared emitter has a range of about 3m (about 
10 feet) at an angle of about 20° from the center of the sensors 
(both front and back).
Do not block the infrared emitter. If the projector does not pick up 
the signals from the remote control, make sure the emitter and 
sensors on the projector are not blocked and that the emitter is 
within range....

Xerox DP 820 User’s Guide19
User Controls
On-Screen Display (OSD) Menus 
The On-Screen Display (OSD) menus provide the options to make 
image adjustments and change a variety of settings. 
The menus can be displayed only when an input source is 
connected to the projector. If the source is a computer, you can 
make changes to the Display settings, and if the source is a video 
device you can make changes to the Video settings. The projector 
automatically detects the type of input source.
Displaying the...

User Controls
20Xerox DP 820 User’s Guide
Image Menu
Contrast—Controls the degree of difference between the lightest 
and darkest parts of the image. Adjusting the contrast changes the 
amount of black and white in the image. The higher the number the 
greater the contrast.
• Press the   button to decrease the contrast.
• Press the   button to increase the contrast.
Brightness—Lightens or darkens the image. The higher the 
number, the lighter the image.
• Press the   button to darken the image.
• Press...

Xerox DP 820 User’s Guide21
User Controls
The correct aspect ratio to select is based on the type of video 
source you are using. If the image seems to be distorted or 
stretched, change the setting.
• Press the     buttons to select one of the aspect ratios.
1:1—The image is displayed without scaling.
16:9—The input source is displayed in wide screen mode 
without scaling. The source is scaled to fit the width of the 
screen.
4:3—The input source is scaled to fit the screen.
Blank Screen—Blanks the...

User Controls
22Xerox DP 820 User’s Guide
Video Menu
[
Saturation—Adjusts the image from black and white to fully 
saturated color. The higher the number, the greater the color 
saturation.
• Press the   button to decrease the amount of color in the 
image.
• Press the   button to increase the amount of color in the 
image.
Tint—Adjusts the balance between the red and green colors in the 
image. Increasing the Tint increases the amount of red in the 
image. Decreasing the Tint increases the amount of...

Xerox DP 820 User’s Guide23
User Controls
Display Menu
Phase—Synchronizes the signal timing of the display with the 
timing of your computer’s graphics card. If the image flickers or is 
unstable, adjust the phase until the image is stable.
• Press the   button to decrease the phase.
• Press the   button to increase the phase.
Tracking—Changes the display data frequency to match the 
frequency of your computer’s graphics card. If vertical flickering 
lines appear on the image, adjust the frequency until...

User Controls
24Xerox DP 820 User’s Guide
Language Menu
Selects the language for the menus and messages displayed on 
the screen.
1. Use the     keys to select the language you want.
2. Press the Menu/Enter button on the projector control panel or 
the   button on the remote control.
The menus will be displayed in the selected language.  

Xerox DP 820 User’s Guide25
User Controls
Advanced Menu
Auto Source Select—The projector automatically scans the 
connected input sources and selects the type that is connected.
• To activate this option, select it, then press the Menu/Enter 
button on the projector control panel or the   button on the 
remote control.
Rear—Projects a reversed image so you can project from behind a 
translucent screen.
• To activate this option, select it, then press the Menu/Enter 
button on the projector control panel...