Yamaha Dpx 1 User Manual

DPX–1
Digital Cinema Projector
Projecteur Cinema Numerique
UCA
OWNER’S MANUAL
MODE D’EMPLOI 

• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance....

FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation...

Caution: Read this before operating this unit.
•To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Installation
•Install this unit in a well-ventilated, cool, dry, clean place with
at least 10 cm clearance on the top, right and left, and at the
back of this unit — away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
•Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming...

English
If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage to this unit may result. Carefully choose
the place to install this unit by avoiding the places listed below.
1.Places where the temperature and humidity vary greatly
•Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely
low.
•This unit must be used within a temperature range of 5—35°C.
2.Places without adequate...

III
Memo 

E-1
INTRODUCTION
INSTALLATION
CONNECTIONS
BASIC OPERATION
MENU
ADDITIONAL
INFORMATION
English
PRECAUTIONS
ENGLISH
Introduction
Features
Contents
INTRODUCTION
Features ............................................. 1
Controls and functions
Front panel and terminal panel ............................................. 2
Control panel ........................................................................ 3
Remote control ..................................................................... 4
Loading the...

E-2
Controls and functions
RS-232C DVI TRIGGER OUT RGB
/YPBPR/YCBCR
D4 VIDEO INPUT A INPUT B VIDEO S VIDEO
VD G
/YR/PR/CRHD/SYNCB/PB/CB
8
123 45 6 790 q w
Focus ring, zoom ring
Focuses and zooms the lens
Remote sensor
Lens
Ventilation (exhaust) slot
Terminal panel 
1—5 INPUT A (BNC jacks)
These jacks receive component video and RGB signals.
Component video signals from an A/V component are sent to
the 1—3 jacks. RGB signals from a computer are sent to the
1—5 jacks. Use a BNC cable when connecting this...

E-3
INTRODUCTION
English
1 indicator (P.14)
2STANDBY/ON button (P.10)
Secondary power button
Turns on and sets this unit in the standby mode. This button is
effective only when the primary power switch is turned on.
Standby mode
In this mode, this unit consumes a small amount of power to
receive infrared siganls from the remote control.
3LAMP/COVER indicator (P.14)
4TEMP/FAN indicator (P.14)
524P indicator (P.14)
6INPUT button (P.11)
Turns on and off the menu to select the input terminal and the
input...

E-4
Controls and functions

Remote control
The corresponding buttons on the control panel and the remote
control perform same functions. Use the remote control by aiming
at the remote control sensor located on the front or back of this
unit. The operation range is 50 degrees horizontally and 30 degrees
vertically within a distance of 6 m (20 feet).
1AUTO button
Readjusts the most appropriate setting for the signal type when
RGB signals are received.
2PATTERN button (P.10)
Turns on and off the stored test...