Yamaha Dpx530 User Manual

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADAYAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANYYAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCEYAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLANDYAMAHA SCANDINAVIA A.B. J A WETTERGRENS...

i
IMPORTANT SAFETY INSTRUCTIONS
• Explanation of Graphical SymbolsThe lightning flash with  arrowhead symbol, 
within an equilateral triangle, is intended to alert 
you to the presence of uninsulated “dangerous 
voltage” within the product’s enclosure that may 
be of sufficient magnitude  to constitute a risk of 
electric shock to persons.
The exclamation point wi thin an equilateral 
triangle is intended to aler t you to the presence of 
important operating and ma intenance (servicing) 
instructions in...

ii
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)Responsible Party: Yamaha Electronics Corporation Address: 6660 Orangethorpe Avenue Buena Park, CA90620
Telephone: 714-522-9105 Fax: 714-670-0108
Type of Equipment: Projector Model Name: DPX-530
This device complies with Pa rt 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received in cluding interference that...

iii
Caution: Read this before operating this unit.
Warning
• This unit must be grounded
 Do not use this projector in a computer room
This projector is not for use in  a computer room, as defined in 
the Standard for the Protection  of Electronic Computer/Data 
Processing Equipm ent, ANSI/NFPA 75.
 Unplug immediately if there is something wrong with  your projectorDo not operate if smoke, strange  noise or odor comes out of 
the projector. It might cause fi re or electric shock. If this 
happens,...

1
Table of contents
1 Preparation 2
Inappropriate places for installation .....................2
Accessory check ..................................................3
Inserting the batteries into the remote control......4
2 Controls and functions 5
Projector overview ...............................................5
Remote control overview .....................................6Using the picture quality adjusting buttons .....6
3 Using the remote control 7
Operational range...

2
◆Inappropriate places for installation
If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Caref ully choose the place to 
install this unit by avoiding the places listed below.
1. Places where the temperature and humidity vary greatly
 Do not install this unit in a place where the temperature and hum idity become extremely high or the temperature becomes extremely 
low.
 This unit must be used within a temper ature range of 41°F...

3
◆Accessory check
The following accessories are provided with  this projector. Check to be sure that all of the accessories are packed in the pack age.
Important
 The supplied power cables are to be used exclusively for this product. Never use them for other products.
 The power cables for use in the U.S. and Europe are included wi th this projector. Use the appropriate one for your country.
 The provided power cable for the U.S. is rated at 120 V. Never  connect this cable to any outlet or power...

4
◆Inserting the batteries into the remote control
1. Remove the rear lid of the remote control.
2. Check the polarity markings (+, –) of the batteries, and set 
them correctly, inserting their (–) side first.
 If the battery is inserted from the  (+) side first, inserting the (–) 
side becomes difficult because  the coil spring end hits on the 
battery side. If the battery is forced to insert in this way, the 
outer label of the battery ma y get ripped and cause a short-
circuit and heating.
3. Attach...

5
◆Projector overview
1. FOCUS ring
2. ZOOM ring
3. Control panel
4. Air intake vent
5. Remote control sensor (Front)
6. Air exhaust vent
7. Air intake vent
8. Terminal board
9. Remote control sensor (Rear)
10. Air exhaust vent
Control area
1. STANDBY / ON,   button
2. AUTO SYNC,   button
3. D-SUB / DVI,   button
4. MENU button
5. STATUS indicator
6. POWER indicator
7. KEYSTONE,  ENTER button
8. VIDEO / S / COMP.,   button
9.  button
Important
 While the menu is on t he screen, the KEYSTONE button...

6
Bottom side
1. Adjustment foot (Front)
2. Lamp cover
3. Adjustment feet (Rear)
4. Air intake vent
Caution
 Do not replace the lamp immediately after using the projector because the lamp will be extremely hot and may 
cause burns.
◆ Remote control overview
1. IR signal transmitter
2. ON (  I ) button
3. DVI button
4. D-SUB button
5. ENTER button
6. MENU button
7. C.TEMP (COLOR TEMPERATURE) button*
8. AUTO button
9. IRIS button
10. GAMMA button*
11. ASPECT button
12. Direction buttons
13. S-VIDEO button...