Yamaha Vl70m User Manual

47
6. Repeat As Necessary
Repeat steps 4 and 5 to edit as many parameters as required.
7. Exit When Done
Press ther [EXIT] button to return to the VOICE EDIT sub-mode menu, or
the [PLAY] button to return to the VOICE PLAY mode when you’re finished
editing.

 IMPORTANT!
• If you want to keep the changes you made in the VOICE EDIT mode, be sure to store the
edited voice to an appropriate INTERNAL voice number before selecting a new voice. 
All
edited data will be lost if you select a new voice before...

48
Pitch Bend........................................................................................52
01: PB Ctrl (Pitch Bend Control)
02: PB LowCtrl (Pitch Bend Low Control)
03: PBLFO PMod (Pitch Bend LFO Pitch Modulation)
Modulation Wheel..........................................................................53
04: MWLFO PMod (Modulation Wheel LFO Pitch Modulation)
05: MWLFO FMod (Modulation Wheel LFO Filter Modulation)...

49Controllers & Control Editing
Embouchure.....................................................................................57
22: Emb CC No. (Embouchure Control Change Number)
23: EmbUpprDpt (Embouchure Upper Control Depth)
24: EmbLowrDpt (Embouchure Lower Control Depth)
25: Emb Mode (Embouchure Mode)
Tonguing..........................................................................................58
26: Tng CC No. (Tonguing Control Change Number)
27: TngCtrlDpt (Tonguing Control Depth)
28: Tng Curve...

50Controllers & Control Editing
 VL-XG Sound Module Mode Control Edit Parameters
Refer to the page numbers listed for full details on each parameter.
Pitch Bend........................................................................................52
01: PB Ctrl (Pitch Bend Control)
02: PB LowCtrl (Pitch Bend Low Control)
03: PBLFO PMod (Pitch Bend LFO Pitch Modulation)
Modulation Wheel..........................................................................53
04: MWLFO PMod (Modulation Wheel LFO Pitch...

51
Throat Formant...............................................................................62
24: Thr CC No. (Throat Formant Control Change Number)
25: ThrCtrlDpt (Throat Formant Control Depth)
Harmonic Enhancer.........................................................................62
26: Hrm CC No. (Harmonic Enhancer Control Change Number)
27: HrmCtrlDpt (Harmonic Enhancer Control Depth)
Damping..........................................................................................63
28: Dmp CC...

52
 Control Edit Parameter Descriptions
The small parameter numbers in parentheses apply in the VL-XG sound module mode.
Pitch Bend
01
(01): PB Ctrl
•Pitch Bend Control
•Settings: -24 … +24
This parameter sets the maximum amount of pitch
bend which will occur when the pitch controller is
set to its maximum position (e.g. when the pitch
bend wheel on a keyboard is rolled all the way up).
Minus setting produce a downward pitch bend.
Each increment corresponds to a semitone. A
setting of “+12”, for...

53Controllers & Control Editing
Modulation Wheel
04
(04): MWLFO PMod
•Modulation Wheel LFO Pitch Modulation
•Settings: 000 … 127
Sets the amount of LFO pitch modulation applied
by the modulation controller (e.g. the modulation
wheel on a keyboard — MIDI control change
number 01). The higher the value the greater the
amount of pitch modulation produced by modula-
tion controller operation. A setting of “000”
produces no pitch modulation.
05(05): MWLFO FMod
•Modulation Wheel LFO Filter Modulation...

54
Assignable Controller
08
(08): AC1 CC No.
•Assignable Controller 1 Control Change Number
•Settings: off … 95
Assigns the specified control change number as
“Assignable Controller 1”. The assigned controller
can then be used to control filter, amplitude, and/or
pitch modulation as specified by the “AC1FilCtrl”,
AC1AmpCtrl, and “AC1LFOPMod” parameters.
below. For example, if this parameter is set to “04”
(Foot Controller), then a MIDI foot controller can
be used to control any of the parameters just...

55
Pressure
13
(12): Prs CC No.
•Pressure Control Change Number
•Settings: off… 95, AT, VEL, PB
“Pressure” corresponds to the amount of breath
pressure applied to a reed or mouthpiece, or the
speed of the bow applied to a string. Pressure
variations affect both volume and timbre. The “Prs
CC No.” parameter specifies the controller to be
used for pressure control. When set to “off”
maximum pressure is applied at all times.
• Please note that pressure affects not only
volume, but timbre and pitch as well....

56
eliminate types. Some voices use very little
filter processing at all. Changing the filter
settings may not produce a particularly notice-
able effect. For detailed filter parameter pro-
gramming use the VL70-m Expert Editor
software (page 25).
17: FilCtrlDpt (VOICE mode only)
•Filter Control Depth
•Settings: -127 … +127
Sets the amount of variation produced by the
controller assigned to dynamic filter. The higher
the value the greater the variation. Positive values
cause an increase in filter cutoff...