Zanussi Zdf 2010 User Manual
Have a look at the manual Zanussi Zdf 2010 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 276 Zanussi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Alarm codeProblem • The start indicator flashes continuously. • The end indicator flashes 1 time intermittently.The appliance does not fill with water. • The start indicator flashes continuously. • The end indicator flashes 2 times intermittently.The appliance does not drain the water. • The start indicator flashes continuously. • The end indicator flashes 3 times intermittently.The anti-flood device is on. Warning! Deactivate the appliance before you do the checks. Turn the programmeknob until the programme marker is aligned with the on/off indicator. ProblemPossible causePossible solution The programme does not start.The mains plug is not connected in the mains socket.Connect the mains plug. The appliance door is open.Close the appliance door. You did not press the start button.Press the start button. The fuse in the fuse box is damaged.Replace the fuse. The appliance does not fill with water.The water tap is closed.Open the water tap. The water pressure is too low.Contact your local water authority. The water tap is clogged or there is limescale on it.Clean the water tap. The filter in the water inlet hose is clogged.Clean the filter. The water inlet hose has a kink or a bend.Make sure that the position of the hose is correct. The anti-flood device is on. There are water leakages in the appliance.Close the water tap and contact the Service. The appliance does not drain the water.The sink spigot is clogged.Clean the sink spigot. The water drain hose has a kink or a bend.Make sure that the position of the hose is correct. After the checks are completed, turn the pro- gramme knob until the programme marker is aligned with programme that was in operation when the problem occurred. The programme continues from the point of interruption.If the problem occurs again, contact the Serv- ice. If other alarm codes show, contact the Service. The washing results and drying results are not satisfactory ProblemPossible causePossible solution The dishes are not clean.The filters are clogged.Clean the filters. 11 www.zanussi.com
ProblemPossible causePossible solution The filters are not correctly assem- bled and installed.Make sure that the filters are correctly assembled and installed. The spray arms are clogged.Remove remaining soil with a thin pointed object. The programme was not applicable for the type of load and soil.Make sure that the programme is ap- plicable for the type of load and soil. Incorrect position of the items in the baskets. Water could not wash all items.Make sure that the position of the items in the baskets is correct and that the water can easily wash all items. The spray arms could not turn freely.Make sure that the position of the items in the baskets is correct and does not cause the blockage of the spray arms. The quantity of detergent was not sufficient.Make sure that you add the correct quantity of detergent in the dispenser before you start a programme. There was no detergent in the deter- gent dispenser.Make sure that you add detergent in the dispenser before you start a pro- gramme. Limescale particles on the dishes.The salt container is empty.Make sure that there is dishwasher salt in the salt container. The set level of the water softener is incorrect.Make sure that the set level of the wa- ter softener agrees with the water hardness in your area. The cap of the salt container is loose.Tighten the cap. Whitish streaks and stains or bluish layers on glasses and dishes.The released quantity of rinse aid is too much.Decrease the released quantity of rinse aid . The quantity of detergent was too much.Make sure that you add the correct quantity of detergent in the dispenser before you start a programme. Dry water drop stains on glasses and dishes.The released quantity of rinse aid was not sufficient .Increase the released quantity of rinse aid. The quality of the detergent can be the cause.Try a different brand of detergent. The dishes are wet.The programme had no drying phase.Set a programme with the drying phase. The dishes are wet and matt.The rinse aid dispenser is empty.Make sure that there is rinse aid in the rinse aid dispenser. The quality of the rinse aid can be the cause.Try a different brand of rinse aid. 12 www.zanussi.com
ProblemPossible causePossible solution The quality of the combi detergent tablets can be the cause.• Try a different brand of combi deter- gent tablets. • Activate the rinse aid dispenser and use the rinse aid together with the combi detergent tablets. Technical information DimensionsWidth / Height / Depth (mm)600 / 850 / 610 Electrical connectionRefer to the rating plate. Voltage220-240 V Frequency50 Hz Water supply pressureMin. / max. (bar / MPa)(0.5 / 0.05 ) / (8 / 0.8 ) Water supply 1)Cold water or hot water2)max. 60 °C CapacityPlace settings12 Power consumptionLeft-on mode0.99 W Off-mode0.10 W 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for theenvironment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. • Discard correctly the packaging material. Re- cycle the materials with the symbol . 13 www.zanussi.com