Acer Aspire 2930 User Manual

							Chapter 3101
13.Hold the connector with one hand and insert the 
Camera Module as shown.14.Lower the camera module as shown
15.Replace the bracket over the Camera Board.16.Replace the single securing screw.
17.Connect the left and right Inverter board cables as shown. 
						

							102Chapter 3
Replacing the LCD Bezel
18. Insert the right side and lower Module in place.19.Replace the single securing screw.
20. Replace the adhesive strip to secure the cabling in place.
NOTE: Ensure all cabling is tucked in under the adhesive strip to prevent damage.
1.Turn the bezel end up and insert the MIC into the underside of the Bezel as shown. 
						

							Chapter 3103
2. Insert the cabling inside the hinge wells to prevent damage or fraying.
3. Starting from the bottom and moving left to right, firmly press down to ensure the bezel is situated correctly 
(four locations on each side).
4. Replace the four screws and the rubber caps provided. 
						

							104Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
Replacing the  Thermal Module
1.Carefully turn the mainboard upside down (CPU 
socket side up), and insert the CPU into the CPU 
socket as shown.2. Using a plastic screw driver, lock the CPU in the 
socket as shown.
1.Align the Fan Module on the screw brackets. 2. Tighten the four (4) captive screws in the order 
shown.
3. Connect the Fan cable to the Mainboard.
1
23
4 
						

							Chapter 3105
Replacing the RJ-11 Jack
1.Insert the RJ-11 cable through the housing well 
and replace the cable cover to secure in place.2.Turn the base over, and insert the cables along the 
well in the bottom cover as shown.
3.Replace the RJ-11 Jack and tuck in cabling in the housing well to prevent damage.
RJ-11 cabling 
						

							106Chapter 3
Replacing the Mainboard
1.Ensure that the Mainboard is facing down (the Heatsink and CPU are not visible). Place the Mainboard in 
the chassis, making sure the I/O ports are positioned correctly through the lower cover, and the screw 
sockets are visible through the mainboard.
2.Before lowering the mainboard completely into 
place, take note of the DC-IN cable. Ensure it sits in 
the housing well as shown. 3.Pull the bottom of the chassis slightly outward to 
allow the I/O ports room for clearance. Lower the 
mainboard and release the lower cover.
4.Connect the modem cable to the mainboard as 
shown.5.Replace the DC-In jack as shown. 
						

							Chapter 3107
6.Replace the three securing screws. 
						

							108Chapter 3
Replacing the Modem Module
Replacing the Bluetooth Board
1.Align the connectors on the mainboard and the 
module and insert the module in place.2. Replace the two securing screws on the modem 
module.
3. Connect the modem cable to the module.
1.Reconnect the cable to the module as shown. 2. Insert the module into the lower base as shown. 
						

							Chapter 3109
Replacing the I/O Board
Replacing the USB Board
Replacing the Launch Board
1.Insert the board at an angle, pivot and set it down 
in place.2. Replace the single securing screw.
1.Align the USB board with the screw socket and 
replace the single securing screw.2. Replace the FFC in connector and lock the 
securing latches to hold the FFC in place.
1.Replace the Launch Board in the bracket. Ensure 
that the FFC passes though the Upper Cover.2. Replace the three securing screws. 
						

							11 0Chapter 3
Replacing the TouchPad Bracket
IMPORTANT:The TouchPad cannot be removed individually. To replace the TouchPad, replace the entire 
Upper Cover.
1.Insert the bracket at an angle as shown.2.Replace the single securing screw.
3.Insert the FFC flush with the connector and lock the securing latch.