Acer Aspire 2930 User Manual

							Chapter 4141
External Mouse Failure
If an external Mouse fails, perform the following actions one at a time to correct the problem. 
1.Try an alternative mouse.
2.If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See 
the mouse user manual.
3.If the mouse uses a USB connection, try an alternate USB port.
4.Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
5.Restart the computer.
6.Remove any recently added hardware and associated software.
7.Remove any recently added software and reboot.
8.Restore system and file settings from a known good date using System Restore. 
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
9.Run the Event Viewer to check the events log for errors. For more information see Windows Help and 
Support.
10.Roll back the mouse driver to the previous version if updated recently.
11 .Remove and reinstall the mouse driver.
12.Check the Device Manager to determine that:
•The device is properly installed. There are no red Xs or yellow exclamation marks. 
•There are no device conflicts. 
•No hardware is listed under Other Devices.
13.If the Issue is still not resolved, see “Online Support Information” on page 235.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or 
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective 
FRUs:
1.Check Drive whether is OK.
2.Check Test Fixture is ok.
3.Swap M/B to Try. 
						

							142Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a 
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement 
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.If no error is detected, do not replace any FRU.
3.If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors. 
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, 
whether a short circuit is suspected, or whether the system is inoperative. 
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On 
Issue” on page 126.):
1.Power-off the computer.
2.Visually check them for damage. If any problems are found, replace the FRU.
3.Remove or disconnect all of the following devices:
•Non-Acer devices
•Printer, mouse, and other external devices
•Battery pack
•Hard disk drive
•DIMM 
•CD-ROM/Diskette drive Module
•PC Cards
4.Power-on the computer.
5.Determine if the problem has changed.
6.If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
•System board
•LCD assembly 
						

							Chapter 4143
POST Codes Tables
These tables describe the POST codes, drivers, and keys for the POST. 
Port 80 POST Codes
The following table details the Port 80 POST codes and drivers used in the POST.
Driver NamePort 80
CodeDriver NamePort 80
Code
PeiEventLog 01 CpuIo 3E
OemServices 02 Cf9Reset 3F
SioInit 03 PcRtc 40
MonoStatusCode 04 StatusCode 41
PentiumMCpuPeim 08 Variable 42
PlatformStage1 09 SmmVariable CF
Variable 0A EmuVariable 43
IchInit 0B TcgDxe A2
PlatformStage2 0D PhysicalPresence A3
IchSmbusArpDisabled 0E TpmDriver AE
ClockGen 12 TcgSmm AE
OpPresence 13 PhysicalPresenceReadyToBoot AE
TcgPei 14 DataHubRecordPolicy AD
FindFv 15 Undi 86
DxeIpl 2F SNP 90
LightMemoryInit 10 BC 91
S3ResumeSoftSmi 11 PxeDhcp4 92
Crc32SectionExtract 31 Ebc 93
OemServices A4 IsaBus 4D
EventLog A5 IsaSerial 4E
ScriptSave 32 Ps2Mouse 6D
AcpiS3Save 33 IdeBus 4F
SmartTimer 34 LightPciBus 50
JpegDecoder 35 UsbBot 6E
PcxDecoder 36 UsbCbi0 6F
PlatformBds 8A UsbCbi1 70
MpCpu 37 UsbKb 71
LegacyMetronome 38 UsbMassStorage 72
FtwLite 39 UsbMouse 74
Runtime 3A Ehci 8F
MonotonicCounter 3B Uhci 73
WatchDogTimer 3C UsbBus 75
SecurityStub 3D SmmBase C2 
						

							144Chapter 4
Driver NamePort80
CodeDriver NamePort80
Code
SmmDisp C5 HiiDatabase 80
SmmReloc C4 OemSetupBrowser 82
SmmRuntime C7 Font(English) 7E
SmmThunk C9 Font(French) 7F
OemServices D8 Font(Chinese) 8D
ChipsetInit 44 UnicodeCollation B1
SmmAccess C0 ConPlatform 5A
PciHostBridge 46 ConSplitter 5D
PciExpress 47 GraphicsConsole 79
GmchMbi CD Terminal 7A
IchInit 48 VgaClass 5E
IdeController 49 SaveMemoryConfig 5B
SataController 4A AcpiSupport 5C
IchSmbusLight 4B AcpiPlatform 53
SmmControl C1 DataHub 5F
Ich7MSmmDispatcher C8 DataHubStdErr 7B
IsaAcpiDriver 4C GenericMemoryTest 61
Fwh 52 DiskIo 60
SmmFwh CE Fat 7C
PciHotPlug 54 Partition 7D
BootOptionPolicy 51 PciPlatform 6B
SetupUtility 76 AlertStandardForma 45
Platform 55 PciSerial A8
PlatformIde 56 AsfInit A7
Ppm D9 IdeRController A9
Platform CC Legacy8259 63
Ihisi D0 LegacyRegion 64
SetupMouse f9 LegacyInterrupt 65
Int15Microcode D1 BiosKeyboard 66
SmmPnp D2 BiosVideo 67
Smbios 57 MonitorKey 68
MemorySubClass 58 LegacyBios 69
MiscSubclassDriver 59 LegacyBiosPlatform 6A
SysPassword AB LegacyMouse 77
PswdConsole AC SmmUsbLegacy 78
HddPswdServiceBody D7 AmtbxInvoke AA
HddPswdService A6 OemBadgingSupport 83 
						

							Chapter 4145
POST Keys and Messages
The following keys are available during POST.
The following messages display during POST:
KeyFunction
F2 Enter into Setup Menu
F12 Enter into Boot Manager
Before press function key
CPUID: XXXXXX
Press F2 go to Setup Utility
Press F12 go to Boot Manager
Press [PXE HOT KEY] go to PXE Setup Menu
After press function key
If user pressed F2
CPUID: XXXXXX
F2 is pressed. Go to Setup Utility.
If user pressed F12
CPUID: XXXXXX
F12 is pressed. Go to Boot Manager.
If user didn’t press any key
CPUID: XXXXXX
Prepare Boot to OS
If user pressed PXE HOT KEY
CPUID: XXXXXX
[PXE HOT KEY] is pressed. Go to PXE Setup Menu. 
						

							146Chapter 4 
						

							Chapter 5147
Jumper and Connector Locations
Top View
No.DescriptionNo.Description
1 LCD Connector 5 MDC Connector
2 Powerboard Connector 6 ExpressCard Board Connector
3 Keyboard Connector 7 BLuetooth Connector
4 DDR3 Connector 8 PCMCIA Connector
13
5 4
6 2
7 8
Chapter 5 
						

							148Chapter 5
Bottom View
No.DescriptionNo.Description
1 CPU Socket 10 Audio Connector
2 DDR2 Connector 11 SPDIF Connector
3 Battery Connector 12 USB Connector
4 ODD Connector 13 HDMI Connector
5 HDD Connector 14 CRT Connector
6 Card Reader Connector 15 Docking Connector
7 HDD Connector 16 RJ 45
8 MXM Connector 17 DC Jack
9 Audio Connector
1
3 2
4
5
6 8 9 1213 14
7
10
11
15
16
17 
						

							Chapter 5149
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for 
Aspire 2930. Aspire 2930 provide one Hardware Open Gap on main board for clearing password check, and 
one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Hardware Open Gap Description
Steps for Clearing BIOS Password Check
If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask 
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is 
necessary to bypass the password check, users need to short the HW Gap to clear the password by the 
following steps:
•Power Off a system, and remove HDD, AC and Battery from the machine.
•Open the back cover of the machine, and find out the HW Gap on M/B as picture.
•Use an electric conductivity tool to short the two points of the HW Gap.
•Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the 
system till BIOS POST finish. Then remove the tool from the HW Gap.
•Restart system. Press F2 key to enter BIOS Setup menu.
•If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and 
try again.
NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
ItemDescription
CLRP2 Clear CMOS Jumper 
						

							150Chapter 5
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS 
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous 
BIOS flashing process failed.
BIOS Recovery Hotkey:
The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered 
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery 
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot 
Block.
Steps for BIOS Recovery from USB Storage:
Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk 
program in another system with Windows XP OS.
Follow the steps below:
1.Save ROM file (file name: JAT10x64.fd) to the root directory of USB storage.
2.Plug USB storage into USB port.
3.Press Fn + ESC button then plug in AC.
The Power button flashes once.
4.Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS. 
5.Update the latest version BIOS for this machine by regular BIOS flashing process.