Home > Apple > Personal Computer > Apple power mac g4 quicksilver User Manual

Apple power mac g4 quicksilver User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple power mac g4 quicksilver User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   69
    1. Disconnect the Ultra2 
    LVD SCSI cable from the 
    Ultra2 LVD SCSI card.  
    						
    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   70
    2. Disconnect the SCSI hard 
    drive power cable (P5). 
    Caution: Pull the SCSI 
    power cable straight out 
    of the connector on the 
    drive. Any up or down 
    motion to the connector 
    could damage the drive.
    Replacement Note: The 
    power cables attach to 
    drives as follows:
    P5 attaches to bay 1
    P2 attaches to bay 2
    P3 attaches to bay 3
    3. Disconnect the Ultra2 
    LVD SCSI data cable from 
    the hard drive.   
    						
    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   71
    4. Remove the hard drive 
    carrier mounting screw.
    5. Pull the drive carrier 
    back and lift up at an 
    angle to release the 
    carrier tabs from the 
    slots in the chassis.
    6. Remove the carrier and 
    drive from the 
    computer. 
    						
    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   72
    7. If youÕre returning the 
    drive to Apple, remove 
    the SCSI data cable and 
    terminator (black 
    plastic housing) from 
    the top of the drive. The 
    cable and terminator are 
    attached to the drive 
    with double-stick foam 
    tape. 
    						
    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   73
    8. If youÕre returning the 
    drive to Apple, you must 
    also remove the hard 
    drive carrier. Remove 
    the four screws from the 
    carrier and lift out the 
    drive.
    Note:  Drives must be 
    returned to Apple in Apple 
    packaging, without cables or 
    carriers. Failure to comply 
    with this requirement may 
    result in a packaging 
    noncompliance charge. For 
    more information, refer to 
    the service parts database. 
    						
    							 Take ApartHard Drive, Ultra2 LVD SCSI  -   74
    9. If youÕre replacing the 
    thermal pad on the 
    drive, remove the old 
    pad and apply the new 
    pad to the same area on 
    the drive.
    Important: Before 
    installing a new 36 GB 
    Ultra2 LVD SCSI IBM 
    drive, you must apply a 
    thermal pad, part 
    number 922-3863. 
    						
    							 Take ApartUltra2 LVD SCSI Card  -   75
    Ultra2 LVD SCSI Card
    Before you begin, open the 
    side access panel.
      
    						
    							 Take ApartUltra2 LVD SCSI Card  -   76
    1. Remove the Ultra2 LVD 
    SCSI card mounting 
    screw. 
    2. Disconnect the Ultra2 
    LVD SCSI cable from the 
    PCI card. 
    Note:  Make sure no 
    external cable is 
    attached to the card. 
    3. Gently lift up on the 
    Ultra2 LVD SCSI card to 
    remove it from the PCI 
    slot. 
    						
    							 Take ApartCarrier Support Plate - 77
    Carrier Support Plate
    Note: Perform this 
    procedure only if you must 
    replace the support plate or 
    the cables below the plate.
    Before you begin, do the 
    following: 
    ¥ Open the side access 
    panel.
    ¥ Remove the hard drive 
    carrier in drive bay 1. 
    						
    							 Take ApartCarrier Support Plate - 78
    1. Remove the two support 
    plate mounting screws 
    from the bottom of the 
    unit. 
    						
    All Apple manuals Comments (41)

    Related Manuals for Apple power mac g4 quicksilver User Manual