Home > Apple > Personal Computer > Apple power mac g4 quicksilver User Manual

Apple power mac g4 quicksilver User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple power mac g4 quicksilver User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 Take ApartPower Supply, Power Mac G4 (QuickSilvers)  -   119
    6. Maneuver the power 
    supply and its cables out 
    of the chassis.  
    						
    							 Take ApartPower Supply, Power Mac G4 (QuickSilvers)  -   120
    Replacement Note: If you 
    are replacing the power 
    supply, remove the power 
    supply bracket and reattach 
    it to the new power supply. 
    						
    							 Take ApartPower Supply, Power Mac G4 (QuickSilvers)  -   121
    Replacement Note: You must 
    set the power supply voltage 
    switch to the correct setting 
    (115 V in North America) 
    to avoid damaging the 
    computer. 
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   122
    Power Supply, PCI/
    AGP Graphics/Gigabit 
    Ethernet/Digital Audio
    Before you begin, do the 
    following:
    ¥ Open the side access 
    panel.
    ¥ Remove the CD/DVD drive 
    bezel.
    ¥ Move the CD/DVD/Zip 
    drive carrier forward 1 
    inch. 
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   123
    1. Disconnect the power-
    to-fan connector. 
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   124
    2. Disconnect the following  
    power cables:
    ¥cables P6 and P7 from 
    the CD-ROM/Zip drive
    ¥Power Mac G4 (PCI 
    Graphics): cable P4 
    from the front panel 
    board 
    ¥main power cable from 
    the logic board
    ¥cable(s) to hard drives 
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   125
    3. Using a 2.5 mm Allen 
    wrench, remove the 
    three screws on the rear 
    vented panel.  
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   126
    4. On the inside of the 
    chassis, remove the 
    screw that attaches the 
    power supply to the 
    power supply shelf.
    5. Slide the power supply 
    forward toward the front 
    of the computer. 
    Maneuver the power 
    supply (clearing the 
    security bar on the 
    inside and upper 
    chassis) and its cables 
    out of the chassis. 
    Note: If you are replacing 
    the power supply, remove 
    the power supply bracket  
    						
    							 Take ApartPower Supply, PCI/AGP Graphics/Gigabit Ethernet/Digital Audio  -   127
    and reattach it to the new 
    power supply.
    Replacement Note: You must 
    set the power supply voltage 
    switch to the correct setting 
    (115 V in the U.S.) to avoid 
    damaging the computer. 
    						
    							 Take ApartSpeaker, Power Mac G4 (QuickSilvers)  -   128
    Speaker, Power Mac 
    G4 (QuickSilvers)
    Before you begin, do the 
    following:
    ¥ Open the side access 
    panel.
    ¥ Remove the carrier 
    support plate. 
    						
    All Apple manuals Comments (41)

    Related Manuals for Apple power mac g4 quicksilver User Manual