Adam Equipment AE Indicators AE402REVB1 User Manual

9 | P a g e              © Adam Equipment Company 2010  
 
6.0  OPERATION 
6.1  ZEROING THE DISPLAY 
 
  You  can  press  the  [Z/T]  key  at  any  time  to  set  the  zero  point.  This  will 
usually  be  necessary  when  the  platform  is  empty.  Wh en  the  zero  point 
is obtained the display will show an indicator for  zero. 
 
 
   
  The  scale  has  an  automatic  re-zeroing  function  to  a ccount  for  minor 
drifting or accumulation of material on the platfor m. However you may 
need  to...

10 | P a g e              © Adam Equipment Company 2010  
   Press  the  [Z/T]  key  to  tare  the  scale.  The  weight  that  was  display ed  is 
stored  as  the  tare  value  and  that  value  is  subtract ed  from  the  display, 
leaving zero on the display. The “ NET indicator will be ON. As a product 
is  added  only  the  net  weight  of  the  product  will  be   shown.  The  scale 
could  be  tared  a  second  time  if  another  type  of  pro duct  was  to  be 
added  to  the  first  one.  Again...

11 | P a g e              © Adam Equipment Company 2010  
 
6.4  PARTS
 COUNTING 
  
If  parts  counting  is  enabled,  See  section  7.4,  it  i s  possible  to  count  parts  using    a 
sample of the parts to determine average piece weig ht.   
 
  Before  starting,  tare  the  weight  of  any  container  t hat  may  be  used, 
leaving  the  empty  container  on  the  scale.  Place  a  k nown  number  of 
samples  in  the  container,  if  used.    The  number  shou ld  match  the 
options for parts...

12 | P a g e              © Adam Equipment Company 2010  
 
 
 
  Press  the  [Pcs/


]  key  to  return  to  normal  weighing.  Press  the  [Pcs/


] 
key again to start counting a different sample. 
   
6.5  CHECK-WEIGHING  
Check-weighing is a procedure to cause lamps to come  on (and if enabled, an alarm 
to sound) when the weight on the scale meets or exc eeds values stored in memory.  
The  memory  holds  the  last  values  for  a  high  and  a  l ow  limit  when  the  power  is 
turned...

13 | P a g e              © Adam Equipment Company 2010  
   
BOTH LIMITS SET The  display  will  show  OK 
when  the  weight  is 
between the limits 
F3 bEP = bP  InL .  
The  beeper  will  sound 
when  the  weight  is 
between the limits, i.e. OK 
 
F3 bEP = bP OtL  
Beeper  will  sound  if  weight 
is outside the limits. 
 
LOW LIMIT SET  
HIGH  LIMIT  is  set  to 
zero 
 
The display will show LOW 
when  the  weight  is  less 
than the  Low  Limit.   Above 
the  Low  Limit  the  display 
will show...

14 | P a g e              © Adam Equipment Company 2010  
NOTE: Weight  must  be  more  than  20  scale  divisions  for  chec k  weighing  to  operate.  
Below  20  scale  divisions  the  LED’s  will  not  light  and  the  beeper  will  not  be 
on. 
   
The  Check-weighing  function    can  be  set  up  during  W eighing  or  Parts  Counting  by 
entering values as Low or/and High Limits keyed in  by the user. The limits are displayed 
in  kg (or Lb)   or pcs  respectively. 
 
  
Checkweighing during...

15 | P a g e              © Adam Equipment Company 2010  
 
6.6  ACCUMULATED TOTAL 
 
  The  scale  can  be  set  to  accumulate  manually  by  pres sing  the 
[Print/M+/Esc]   key  or  automatically  when  a  weight  is  removed  from  
the  scale.    See  the  Section  7.3  for  details  of  sett ing  the  Parameter  “C3 
PRM ”  and  “ C4  Aon”.    The  accumulation  function  is  available  when 
weighing  or  when  counting  parts.    However  the  memory   is  cleared  if 
the weighing units or...

16 | P a g e              © Adam Equipment Company 2010  
  
6.7  PERCENT
 WEIGHING  
 
The scale can be set to perform percent weighing.   See Section 7.2. 
  
The  scale  will  use  a  mass  on  the  platform  as  the  100 %  reference  weight.  If  the 
platform  is empty  (or  the scale  is  tared)  then  the  user can  input  a  reference  weight 
using the keypad.   
  
  Press   [Func/C] .  The  first  option  is  “FunC  1”,  press  the   [Func/C]  key  again 
display  “FunC 2” .  
 
   Press...

17 | P a g e              © Adam Equipment Company 2010  
  The  number  of  decimal  points  will  depend  on  the  wei ght  used  in  comparison 
to the capacity of the system.  A smaller weight wi ll show only “100%” while a 
larger weight might show “ 100.00%”.    
 
  If  the  scale  was  showing  zero  weight  when  entering  this  function,  then  the 
user must manually enter the weight to be set as 10 0% as described below. 
 
  Press the  [Z/T] key. “P1  PCt”  will be displayed.  
 
  Press...

18 | P a g e              © Adam Equipment Company 2010  
6.8  ANIMAL (DYNAMIC) WEIGHING  
The  scale  can  be  set  to  animal  (dynamic)  weighing  f or  weighing  any  items  that  are 
unstable or may move.   See Section 7.4.    
The scale will use a special filter to minimise the  effects of any movement while the 
moving animal or unstable samples are on the scale.   
  
  Press   [Func/C] .  The  first  option  is  “FunC  1”,  press  the   [Func/C] key  again  to 
display  “Func 2” .  
 
 
...