Addonics Technologies 15 Hard DriveSSD Duplicators HDUS5325DX user guide

							Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v3.1.11
www.addonics.com
User Guide
1:5 HDD Duplicator Deluxe
(HDUS5325DX)
T E C H N O L O G I E S
ENT
ESCDuplicator Panel
S ource  Drive
Target  Drives
P ower S witch         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
I. Installing  Drive int o the  HDD D uplicator
Step  1
O pen t he source  drive door and slide  in the 3. 5” SATA  hard  disk S ource  drive into the drive  bay. Close t he 
f ront  panel  and us ing the key  provided, t urn the key  lock to t he Lock  position. T his will  secure t he drive 
and t urn on the power t o the  hard  drive.
S tep  2
O pen t he target  drive door(s)  and slide  in the 3. 5” SATA  hard  disk T arget  drive(s)  into the drive  bay. Close 
t he f ront  panel  and us ing the key  provided, t urn the key  lock to t he Lock  position. T his will sec ure the drive 
and t urn on the power t o the  hard  drive.
Note : Ref er to the S nap-In  25 user  guide f or 2.5” SATA  hard  drive  installat ion on t he HSUS 3325DX.
II.  C onnecting  the Power  Cable and Powering Ona.  Connect the  power cord provided f rom the wall  out let to  the  back  of the t ower.
b.  A  main power  switch is locat ed at the  back o f the tower. T urn the swit ch on. A nother  auxiliary  
  switch is locat ed on t he front  of the t ower.
c.  P ush the aux iliary  switch  button t o turn  on the HDD  duplicator.
III.  The Duplicator  PanelThere  are four buttons  and an LCD  on the panel o f HDD  Duplicator.
1 –  LCD s hows a  funct ion or a  mess age.
2 – i t is  us ed t o sc roll up f unct ion menus.
3 – i t is  us ed t o sc roll down f unction menus.
4 – i t is  us ed t o execute a  funct ion.
5 – i t is  us ed t o canc el a function.
 
IV.  D uplicating  a d rive
W hen t he duplicat or powers  on, it  init ializes  and goes t hrough t he steps below
S hows t he firmware  version  I nitialize S DRAMs stat us.. 
      
Det ect  Drives  status
 .   Shows the first funct ion: 
      
Copy  HDD copies  data directly f rom the source  hard disk to  the t arget  hard disk. 
HD D uplicator
1-1 V er:Initialize S DRAM
Detect  Drives1.C opy HD
ENT
ESC
Duplicat or Panel
1
2
34
5
Basic Instructions 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Press ENT  button to begin copy. T he system  will aut o-detect the hard  disks  and  show t he following info 
on t he LCD.
 
T he  LCD  will show t he following  info during t he copying  process:  remaining t ime, complet ed percent age. 
T he  copy  s peed, capacity  and  time will  v ary depending  on  the source  hard disk.  O nce  the copying 
proc ess is complete  the  LCD  will display t he following  results.
 
C opy-36MBs   0%
235.7GB          1:48
Copy HD
OK: 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Functions
The copy controller has  11 functi ons in total , with t he 11th (Adv Set up) being a hid den system function that  only appears when the  ESC key is pressed for 2 seconds until there is a  beep. These are shown below. 
10-01. L anguage           
10- 02. C opy Size          
10-03. Start up Menu     
10-04.  Auto Com pare   
10-05. Butt on Sound     
10-06. Device Info        
10-07. System  Info        
10-08. Fast  Copy          
10.  Setup
10-09. Auto Start Drive 
10-10.  Auto Start Timer
10-11. Toler ance Size  
Duplicator C ontroller
1. Copy  HDD           
2. Async C opy HDD
3. Compare  HDD   
4. Async Compare 
5. PreScan Source
6. ReScan BUS     
7. Source Size        
11. Adv Setup
11-01. Read Error Skip     
11-02. U pdate  Firmware   
11-03.  Compare  Firmware 
11-04. Quick Erase  HDD   
11-05.  Full Erase  HDD     
11-06.  H/W  Diagnostic     
11-07. L oad  Default         
8. Secure Erase    
9. Overwrite           
10- 12. B ootTime Delay
10-13. Quick Com pare 
11-08.  Copy HPA              
11-09. Burn  In                      
10. Setup                 
11. Adv Set up            
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Copy HDD
Copy  HDD copies data directly from  the source  hard disk t o the t arget  hard disk. Pl ease make sure that the capacity of  the target hard disk is equal or larger t han the source  hard disk. 
Choose option 1 from  the m enu: 
Press  ENT to  begin copy. The system w ill auto-detect the hard di
sks and show  the fo llowing copying info on t he LCD. 
The LCD w ill show the follo wing info during the copyin
g process: elapsed time, completed percentage. The copy speed, capacity and time wi ll vary depending on the source hard disk. Once the copying process is complete the LCD will display the following results. 
Copy- 36MB/s       0%
2 32.9GB     00: 00:00
Copy  HDD                
OK: 11        Fail: 0
1. C opy  HDD            
HDD:11     232.9GB
Async Copy HDD
This option is used to specify the size of the source for simplifying fu\
rther copying operations.
Choose option 2 from the me nu: 
2. Async Copy HDD 
HDD: 10    232.9GB
Press  ENT. Before the start of t he reproduction, if t he console  detects that a  hard drive 
capacity is less t han source, then the LCD will show t he cor
responding channel number.
8
Space Not  Enough
A nd then automatically copies. The LCD will display t
he following info.
Acpy- 36MB/s      0%
232.9GB    00:00:00
If the rep lication process to conti nue to add additi
onal hard disk  device, LCD will only show the last completed perc entage.
Once t he copying process is complete t he LCD w ill display the fo llowing results.
Async C opy HDD
OK:  11      Fail:  0
Compare
Compare HDD is used to see if  the data on a source hard disk is i dentical to the target hard disk after the C opy HD operation. 
Choose option 3 from the me nu:  
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
3. Compare HDD     
HDD: 11      232.9GB 
Press  ENT to  begin  the comparison. The L CD will display  the fol lowing info.
Comp-23MB/s    0%
232.9GB    00:00:00
Once t he comparison is complete  the LCD wi ll display  t he following info as well as t he amount of 
data  on the source  hard disk. 
Compare   OK:11
Fa il: 0       Dif: 0
PreScan S ourcePreScan HDD is used to check if the source hard disk can be accessed pro\
perly.
It also tests the read speed.
Choose option 5 from  the m enu:
5. PreScan S ource  
HDD : 11    232.9GB
Async Compare
Compare HDD is used to see if the data on a source hard disk is identica\
l to the
target hard disk after the Copy HDD operation. While compare process is
on-going, allows you to plug-in additional target drives and comparison \
will
automatically start for the added target drive.
Choose option 4 from the me nu: 
4. Async Compare    
HDD: 11      232.9GB 
Press  ENT
 to  begin  the async comparison. The L CD will display the fo llowing info.
ACmp-23MB/s   0%
232.9GB   00:00:00
Compare   OK:11
Fa il: 0       Dif: 0
If the comparison process continu
es to add additiona l  hard disk device, LCD w ill only show the 
last  completed percentage.
Once t he copying process is complete t he LCD w ill disp lay t he following results.
Press  ENT
 to  begin scan. The L CD will display  the fo llowing inf o
Scan- 90MB/s    1%
230.6GB   00:00:27
Once t he scan is complete , the L CD w ill display  the corresp onding results
 PreScan OK!        
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
6. ReScan BUS      
ReScan Bus
Choose  option 6 from t he menu: 
Press  ENT to re-scan hardware. The LCD wi ll display the follo
wing info. 
Re-Scan BUS NOW?
Yes
Wh en the scan is complete the L CD will display the fol lowing info. 
Bus re- scan OK !      
     
7. S ource Size        
Source Size
Source Size is used to show the capacity of the source.  
Ch oose option 7 from  the m enu: 
Press  ENT and  the L CD w ill show the fo llowing info. 
HDD:Hitachi
Size: 232.9GB         
Then press  ENT and the L CD w ill show the  datas size info. 
HDD:Hitachi
Data: 200.9GB        
8. Secure Erase    
Secure Erase
Secure Erase is used to wi pe the data of  the hard disk,  it will erase a ll of HDD of dup licator (included Source  HDD). 
Ch oose option 8 from  the m enu:
Press  ENT to access  option. By default it is set  to No . Use  the Up 
and Down arrow keys t o choose Yes.
Wipe a ll data.
Conti nue? No        
Press  ENT and  the L CD w ill show the fo llowing info. 
ReScan Bus allows swapping the source or target in and out without having to
reboot the system. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10. Setup              
SetupSetup allows various system settings to be changed. There are 12 sub-opt\
ions:
Language, Copy Size, Startup Menu, Auto Compare, Button Sound, Device In\
fo,
System Info, Fast Copy, Auto Start Drive, Auto Start Timer, Tolerance Si\
ze and
Boot Time Delay.
Ch oose option 8 from  the m enu: 
In Process
Elapsed  01:00    
9. Overwrite         
Overwrite
Overwrite is used to overwrite  the  data of the  hard disk, it will erase a ll HDDs connected to the  duplicator 
(includ ing Source  HDD). There are 3 sub-options:  One pass, 3 pass  and 7 pass.
Ch oose option 9 from  the m enu:
Press  ENT to access option. By  default it is O ne pass Use the  Up a nd Down arrow keys to ch oose 
other options.
9- 01. Overwrite   
O ne pass
Press  ENT to access option. By  default it is set to No. Use th e Up a nd Down arrow keys to choose 
Yes.
Wipe a ll data.
Conti nue? No     
Press  ENT and the LCD will show t he following info. 
In Process
Elapsed  01:00  
Language
This opti on is used to select  the systems lan guage support. By default  this is set to Eng lish. Press 
ENT  to change the Langu age settings.
Language
Eng lish                     
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-02. Setup
Copy Size               
Press  ENT and the LCD will display a deta iled list of opti ons as shown  below
Use the Up  and Down arrow keys t o choose dierent copy si zes.  The system w ill oer their 
corresponding  percentages so the user can specify t he amount  to copy from  the source hard disk. 
Press  ENT to confrm  and save the changes.
C opy Size
100%~1 % (*MB)    
Startup Menu
This opti on allows you to set an opti on other than Se tup to be display ed as the frst ava ilable 
opti on on t he m enu every time you star t the system.
Startup M enu
1. C opy  HDD         
Press 
ENT then use  the Up and Down a rrow keys to choose other opt ions. By  default the frst 
m enu option is Copy  HDD.
10-03. Setup
Startup M enu         
Auto Compare
This opti on automatica lly compares the source hard disk wit h t he target  hard disk after a copy 
operation is completed.
Press  ENT to access  option. By default it is set to O. Use th e Up  and Down arrow keys to choose 
On.
Auto Com pare
O                          
10-04. Setup
Auto Compare       
Copy Size
This option is used to specify the size o f the source  hard disk for simp lifying further copying 
operations. 
Button Sound
This option is used  to control the so und of a button when y ou press it.
10-05. Setup
Button Sound        
Press  ENT and  the L CD w ill display  the fo llowing info. Use  the  Up  and Down a rrow keys to ch oose 
w hether  button sound is  on or o. 
Button Sound
On