AEG Freestanding dishwasher F66609M0P User Manual

							dispenser is activated (factory
setting).
3. Press  Start to change the setting. = the rinse aid dispenser is
deactivated.
4. Press the on/off button to confirm
the setting.7.  OPTIONSDesired options must be
activated every time before
you start a programme.
It is not possible to activate
or deactivate options while a
programme is running.Not all options are
compatible with each other.
If you have selected non
compatible options, the
appliance will automatically
deactivate one or more of
them. Only the indicators of
the options still active will
stay on.7.1  Multitab
Activate this option when you use multi-
tablets that integrate the salt, rinse aid
and detergent functions. They can also contain other cleaning or rinsing agents.
This option deactivates the release of salt. The salt indicator does not come on.
This option also deactivates the release
of rinse aid but only when the rinse aid dispenser is deactivated, (rinse aid
indicator does not come on). If the rinse
aid dispenser is activated, rinse aid is
released even with the option Multitab
activated.
With the use of this option the programme duration is prolonged to
increase the cleaning and drying results
with the use of multi-tablets.
Multitab is not a permanent option and
must be selected at every cycle.
How to activate Multitab
Press  Option  until the indicator  comes
on.
7.2  TimeSaver
This option increases the pressure and the temperature of the water. The
washing and the drying phases are
shorter.
The total programme duration decreases by approximately 50%.
The washing results are the same as with
the normal programme duration. The drying results can decrease.How to activate TimeSaver
Press  Option  until the indicator comes on. 
If the option is not applicable to the
programme, the related indicator does not come on or it flashes quickly for afew seconds and then goes off.
The display shows the updated
programme duration.
7.3  ExtraHygiene
With this option you have better hygiene
results. During the last rinsing phase, the
temperature stays at 70 °C for at least 10
minutes.
How to activate ExtraHygiene
Press  Option  until the indicator comes on. 
If the option is not applicable to the
programme, the related indicator does not come on or it flashes quickly for afew seconds and then goes off.
The display shows the updated
programme duration.
ENGLISH11       
						

							8. BEFORE FIRST USE1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the
baskets.
When you start a programme, the
appliance can take up to 5 minutes to
recharge the resin in the water softener.
It seems that the appliance is not
working. The washing phase starts only
after this procedure is completed. The
procedure will be repeated periodically.8.1  The salt containerCAUTION!
Only use salt specifically designed for dishwashers.
The salt is used to recharge the resin in
the water softener and to assure good washing results in the daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt
container (Only for the first time).
3. Fill the salt container with dishwasher
salt.
4. Remove the salt around the opening
of the salt container.
5. Turn the cap of the salt container
clockwise to close the salt container.
Water and salt can come out
from the salt container when
you fill it. Risk of corrosion.
To prevent it, after you fill
the salt container, start a
programme.8.2  How to fill the rinse aid
dispenserCAUTION!
Only use rinse aid
specifically designed for dishwashers.
1. Open the lid ( C).
2. Fill the dispenser ( B) until the rinse
aid reaches the marking ''MAX''.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the lid
locks into position.
www.aeg.com12    AB
C   
						

							Fill the rinse aid dispenser
when the indicator ( A)
becomes clear.9.  DAILY USE1.Open the water tap.
2. Press the on/off button to activate
the appliance.
Make sure that the appliance is in
programme selection mode. • If the salt indicator is on, fill thesalt container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent. If you use multi-
tablets, activate the option Multitab.
5. Set and start the correct programme
for the type of load and the degree
of soil.9.1  Using the detergentCAUTION!
Only use detergent specifically designed for
dishwashers.
1. Press the release button ( A) to open
the lid ( C).
2. Put the detergent, in powder or
tablets, in the compartment ( B).
3. If the programme has a prewash
phase, put a small quantity of
detergent on the inner part of the
appliance door.
4. Close the lid. Make sure that the lid
locks into position.
9.2  Setting and starting a
programmeThe Auto Off function
This function decreases energy
consumption by deactivating
automatically the appliance when it is not operating.
The function comes into operation: • 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.
Starting a programme
1. Close the appliance door.
2. Press the on/off button to activate
the appliance. Make sure that the
appliance is in programme selection
mode.
3. Press  Program  again and again until
the indicator of the programme you
want to select comes on.
The display shows the programme
duration.
4. Set the applicable options.
5. Press  Start to start the programme.
• The indicator of the running phase comes on.
• The programme duration starts to decrease with steps of 1 minute.
Starting a programme with
delay start
1. Set a programme.
2. Press  Delay  again and again until the
display shows the delay time you
want to set (from 1 to 24 hours).
3. Press  Start to start the countdown.
• The delay indicator comes on to confirm the start of the
countdown.
• The countdown starts to decrease with steps of 1 hour. Only the last
ENGLISH13 AB
C   
						

							hour will decrease with steps of 1
minute.
When the countdown is completed, the programme starts and the indicator of
the running phase comes on. The delay indicator goes off.Opening the door while the
appliance operates
If you open the door while a programme
is running, the appliance stops. When you close the door, the appliance
continues from the point of interruption.
Cancelling the delay start while
the countdown operates
When you cancel the delay start you have to set the programme and options
again.
Press simultaneously  Delay and Option
until the appliance is in programme selection mode.
Cancelling the programme
Press and hold simultaneously  Delay and 
Option  until the appliance is in
programme selection mode.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.End of the programme
All buttons are inactive except for the
on/off button.
1. Press the on/off button or wait for
the Auto Off function to
automatically deactivate the
appliance. 
If you open the door before the activation of Auto Off, the appliance
is automatically deactivated.
2. Close the water tap.
10.  HINTS AND TIPS10.1  General
The following hints will ensure optimal
cleaning and drying results in daily use
and also help to protect the
environment.
• Remove larger residues of food from the dishes into the waste bin.
• Do not pre-rinse dishes by hand. When needed, use the prewash
programme (if available) or select a
programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the dishes can be
completely reached and washed by
the water released from the spray arm nozzles. Make sure that items do not
touch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',
''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
• Select the programme according to
the type of load and degree of soil.With the ECO programme you havethe most efficient use of water and
energy consumption for crockery and
cutlery with normal soil.10.2  Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for dishwasher. Other products can
cause damage to the appliance.
• Multi-tablets are usually suitable in areas with a water hardness up to 21
°dH. In areas exceeding this limit,
rinse aid and salt must be used in
addition to the multi-tablets.
However, in areas with hard and very
hard water we recommend to use
solo-detergent (powder, gel, tablets
without additional functions), rinse aid
and salt separately for optimal
cleaning and drying results.
• If you use multi-tablets you can select the Multitab option (if available). This
option increases the cleaning and drying results with the use of multi-
tablets.
• Detergent tablets do not fully dissolve with short programmes. To prevent
www.aeg.com14 
						

							detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
• Do not use more than the correct quantity of detergent. Refer to the
instructions on the detergent
packaging.10.3  What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according to the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
10.4  Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made of wood, horn, aluminium,
pewter and copper.
• Do not put in the appliance items that can absorb water (sponges,
household cloths).
• Remove remaining food from the items.
• Make soft the remaining burned food on the items.
• Put hollow items (cups, glasses and pans) with the opening down.
• Make sure that cutlery and dishes do
not bond together. Mix spoons withother cutlery.
• Make sure that glasses do not touch other glasses.
• Put small items in the cutlery basket.
• Put light items in the upper basket. Make sure that the items do not
move.
• Make sure that the spray arm can move freely before you start a
programme.10.5  Before starting a
programme
Make sure that:
• The filters are clean and correctly installed.
• The cap of the salt container is tight. • The spray arms are not clogged.
• There is dishwasher salt and rinse aid (unless you use multi- tablets).
• The position of the items in the baskets is correct.
• The programme is applicable for the
type of load and for the degree of
soil.
• The correct quantity of detergent is used.
10.6  Unloading the baskets
1.Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
At the end of the
programme water can still
remain on the sides and on
the door of the appliance.11.  CARE AND CLEANINGWARNING!
Before maintenance,
deactivate the appliance and
disconnect the mains plug
from the main socket.Dirty filters and clogged
spay arms decrease the
washing results. Make a
check regularly and, if
necessary, clean them.ENGLISH15    
						

							11.1 Cleaning the filters
The filter system is made of 3 parts.
1. Turn the filter ( B) counterclockwise
and remove it.
2. Remove the filter ( C) out of filter ( B). 
3. Remove the flat filter ( A).
4. Wash the filters.
5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.www.aeg.com16C BA         
						

							11.2 Cleaning the spray arms
Do not remove the spray arms. If the
holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.11.3  External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning pads or solvents.
11.4  Internal cleaning
• Carefully clean the appliance, including the rubber gasket of the
door, with a soft moist cloth.
• If you regularly use short duration programmes, these can leave
deposits of grease and limescale
inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.12.  TROUBLESHOOTINGIf the appliance does not start or it stops
during operation. Before you contact an
Authorised Service Centre, check if you
can solve the problem by yourself with
the help of the information in the table.With some problems, the display
shows an alarm code.Problem and alarm codePossible solutionYou cannot activate the ap-
pliance.• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no damaged fuse in the fuse box.The programme does not
start.• Make sure that the appliance door is closed. • Press  Start.
• If the delay start is set, cancel the setting or wait for the end of the countdown.
• The appliance has started the procedure to recharge the resin inside the water softener. The duration of the
procedure is approximately 5 minutes.The appliance does not fill
with water.
The display shows 
.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For this information, contact your local waterauthority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.The appliance does not
drain the water.
The display shows 
.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.The anti-flood device is on.
The display shows 
.
• Close the water tap and contact an Authorised Service Centre.ENGLISH17    
						

							Once you have checked the appliance,deactivate and activate the appliance. Ifthe problem occurs again, contact an
Authorised Service Centre.For alarm codes not described in the
table, contact an Authorised Service
Centre.12.1  The washing and drying results are not satisfactoryProblemPossible solutionThere are whitish streaks or
bluish layers on glasses and
dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position.
• The quantity of detergent is too much.There are stains and dry water
drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid selector to a higher position.
• The quality of the rinse aid can be the cause.The dishes are wet.• The programme does not have a drying phase or has a drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.Refer to " Hints and tips " for
other possible causes.13.  TECHNICAL INFORMATIONDimensionsWidth / height / depth (mm)596 / 850 / 610Electrical connection 1)Voltage (V)220 - 240Frequency (Hz)50Water supply pressurebar (minimum and maximum)0.5 - 8MPa (minimum and maximum)0.05 - 0.8Water supplyCold water or hot water 2)max 60 °CCapacityPlace settings13Power consumptionLeft-on mode (W)0.99Power consumptionOff-mode (W)0.101) 
Refer to the rating plate for other values.
2)  If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the
hot water supply to decrease energy consumption.www.aeg.com18  
						

							14. ENVIRONMENT CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
ENGLISH19   
						

							www.aeg.com/shop117904871-A-282014