Aimco Brakes AcraDyne Torque Cart Manual

-
39  - Too
lsTrac  Configuration  Set tings: Aler ts 
1.Click on Settings  from the top pull-down menu.
2. Click on Program Settings  in the pull-down
menu.
3. Click on Al erts  in  the Program Settings  pull- 
down menu
. Custom
  Lab els 
1.Click on Settings  from the top pull-down menu..
2
. Click on  Program Settings  in the pull-down menu.
3.Click on Custom Labels  in the Program Settings  pull-down menu.
4. You may change the name of Asset
Number, but cannot be de-selected
as inactive.
5. There...

-
40  - Too
lsTrac  Configuration  Set tings: Loo kups 
6.Click on Settings  from the top pull-down menu.
7. Click on Program Settings  in the pull-down menu.
8.Click on LookUps  in the Program Setti ngs pull-down menu.
9. One of the important usages for the LookUps menu is for Tool Location Tracking. Selecting the
Location Lookup allows to add locations
. Click on the empty location box to enter the name of the
location. The Checkbox can be used to enable/disable that lo
c at ion. Now when...

-
41  - Too
lsTrac  Configuration  Set tings: Using 
an  Ex tern al  Tran sduc er 1.Click on Settings  from the top pull-down menu.
2. Click on Program Settings  in the pull-down menu.
3.Click on External Transducer  in the Program Settings  pull-down menu.
Note: When External Transducer is enabled, the pulse readings view in the torque verification sc reen
will be replaced with the external torque readings dat a. Pulse info does not get recorded or saved for
external transducer verifications
. Whenever...

-
42  - To
rque  Ca rt:   Maintenance  Maintenance activities must be performed with the machine power turned off and locked out. Failure 
to 
do so may cause injury or damage to the cart.   Proper maintenance of your machine is essential to insure repeatability of torque re
adings and prevent 
excessive downtime   Electrical System 
Repairs should be made to the electrical system by or under the direc
t supervision of a 
qualified electrici an.  
Keep all electrical wires and connections free from oil,...

-
43  - To
rque  Ca rt:  Tr oubleshooting   Problem:
 If transducers won’t communicate with ToolsTr ac.   So
lut ion:  Make sure the power switch is in the on position and the cart has a 
char ge.  If not, plug in the  AC power cord for charging (8 hours for full c
harge ).   No
te: If you still have a problem: For the Laptop option: Check the computer and see if the Laptop is  charging, by looking at the bottom right hand corner of the scre
en
. If you see a plug, the computer is  
charging
. Check the...

-
44  - Torq
ue Ca rt:   Parts  List Qt y. Part # Description  1
 21888 Transducer, Industry Std. 20
 NM 1/4”  he x dr.  1
 21887 Transducer, Industry Std. 75 NM 3/
8” sq  dr.  1
 21886 Transducer, Industry Std. 180 NM 1/
2” sq  dr.  1
 21885 Transducer, Industry Std. 500 NM 3/
4” sq  dr.  1
 22332 Transducer cable, extern
al  1
 22361 Transducer cable, 
intern al  1
 22259 16 
Bit DSP module  1
 22167 LED
 Interconnect board  1
 23289 Utility 
cart  

-
45  - Tor
que  Ca rt:   P hotos  Utility Cart  

-
46  - Tor
que  Ca rt:   Glos sary  Angle: 
The measure of degree of rotation of a fastener from threshold torque to fi nal 
torque. This typically does not include the free rundown before the he ad of  
the fastener hits the surface of the wo rk piece.  Angle Lo/High: 
Angle is typically measured during rundown of continuous drive tools to  
detect cross threading (for low angles) and stripping or yielded fasteners (for 
high angle s). 
  Calibration: 
Setting a device to a known standard. CAN:...

-
47  - UFT  J
oint  Simula tor:  O perat ions  Instructi ons  UFT-S10 and UFT-S16 
These testers are capable of simulating four different joints:  A, B, C, and D (hard, medi
um-hard, 
medium-soft, and soft, respectivel y).   A Joint: 
C and D valves closed (clockwise) and the A joint sleeve installed between the  Plunger Bushing and the Spindle Nut.  
B Joint: 
C and D valves closed (clockwise) and remove the A joint 
sleev e.  C Joint: 
Open the D valve under the side cylinder one turn (count er-cl o...

-
48  - UFT  J
oint  Simulator:  B reak do wn  of  the  UFT-S  J oint  Simu lator Top Vie w of UFT-S Joint S imulator 
Side View  of UFT-S Joint  Simulator