Aimco Brakes AcraDyne Torque Cart Manual

-
59  - 44   966 - 100 - 0   Allen Head Plug (1/8 )   6   

-
60  - UFT  J
oint  Simulator:  Mainten ance 1. Inspect the Bolt and Spindle Nut every 50,000 cyc les.
2. Should the Plunger not come back up to the top of the Cylinder, then the teste r is low on f luid.  To fill
the tester with fluid, the tester must be level.
•Remove the two oil filler plugs from the plunger.
•Pull the plunger back up to the top of the cylinder.
•While holding the plunger up, fill the tester up through the filler holes with Dextron II.
•Reinstall the oil filler plugs.
3. If the...

-
61  - UFT  J
oint  Simulator:  Certificati on  of  the   UFT  J oint  Simu lator  The UFT tester should be certified every 5,000 cycles. Certification Proce
dures 
1. On the chart below, find the UFT model you are certifying.
2. Next, find the bolt size.
3. With a torque wrench, tighten to the recommended snug torque.
4. Turn the torque wrench the number of degrees recommended from snug for each joint.  The torque
reading should be the same as shown on the chart.
5. If the readings do not match, the...

-
62  - UFT  J
oint Simulator:  List of  He xag on Head  Bol ts For UFT Joint Simulators 
MODEL PART NUMBER BOLT SIZE  UFT - 6
  946 - 967 - 0  M 4 
UFT - 6
  946 - 968 - 0  M 5 
UFT - 6
  946 - 969 - 0  M6 x 18 
UFT - S10
  946 - 970 - 0  M6 x 30 
UFT - S10
  946 - 971 - 0  M8 x 32 
UFT - S10
  946 - 972 - 0  M10 x 35 
UFT - 10  946 - 970 - 0  M6 x 30
 
UFT - 10  946 - 971 - 0  M8 x 32
 
UFT - 10  946 - 972 - 0  M10 x 35
 
UFT - S16
  946 - 973 - 0  M12 x 45 
UFT - S16
  946 - 974 - 0  M14 x 50 
UFT -...

-
63  - Utility 
Cart:  Safety  Precautio ns FOR SAFET Y: 
1. Do not Operate, maintain or service machine:
•Unless trained and authorized.
•Unless operation manual is read and understood.
•In flammable or explosive areas
2. Before operating machin e:
a. Make sure all safety devices are in place and operate prope rly.
3. When maintaining or servicing machine:
•Disconnect battery connections before working on machine.
•Avoid contact with battery acid.
•Avoid moving parts. Do not wear loose jackets, shirts,...

-
64  - Utility 
Cart:  General  Specificati ons  Electric 24 V DC-(2) 12V batteri
es  
Charger, 110 VAC, 60 HZ/220 V AC POWER TRAIN/ PROPELLING SYSTEM  24 V DC Electric motor 
24 V DC controll
er 
SUSPENSION  SYSTEM  Casters-(1) rear, 5 in
. (127 mm) dia. 
 
Dr ive -(2) front, 10 in. (25 4mm) dia. 
GENERAL MACHINE DIMENSIONS  Length-36.0 in
. (914 mm
)  
Width-20.5 in
. (521 mm )  
Height-41.4 in
. (1042 mm) 
MACHINE  Total weight, with batteries-300 lb. 
Utility 
Cart:  Additional  Specifica tions...

-
65  - Utility  Cart:  Adjustm
ents  Controls: 
The handle assembly can easily be adjusted if the machine comes out of neutral and begins to creep. By  
removing the (4) 5/16” self -threaded screws in the yellow control box, you will gain access to the con trol 
potentiometer
. Adjust the potentiometer with a ½ inch SAE wrench. Turning the potentiometer towards  
the front of the machine will stop the machine from creeping bac kwards. Turning the potentiometer  
towards the rear of the machine will stop...

-
66  - Utility 
Cart:  Ac cessory  Panel  A.Power Switch
The Power switch controls the machine power.
Turn the key to (1) to turn on the ma
chine power.
Turn the key to (O) to turn off the ma chine power.
The machine batteries must be charged for the machine to 
have power.
B.Main Circuit Breaker The main circuit breaker protects the motor from over load
. If the load is too high, the main circuit
breaker will trip and the unit will stop. To reset the circuit breaker, press the circuit breaker re set...

-
67  - Utility 
Cart:  Maintenance 
The Daily and Monthly maintenance requirements listed here may be performed without tools by the  
machine operators
. Instructions for these maintenance requirements are provided in this section of t he 
manual
.   
DAILY:  Perform all duties listed under the PRE-OPERATION check lists. 
EVERY 
THREE MONTHS:  Lubricate castor bearings with gr
ease.  
Check and tighten all fasteners and hardware.  
Clean, tighten and lubricate battery posts and cable s. 
Check...

-
68  - Utility 
Cart:  Serv ice  Poli cy 
Whenever ordering parts or requesting any type of service, please spec ify:  1. The model of the machi ne
2. Serial number
3. The part number
4. The part description Utility  Cart: 
Load  Limits 
The PartsCaddyLite is specifically designed for moving materials, parts, or ma chinery
. You should never 
operate the PartsCaddyLite:  
•With an operator under the age of 16 years of age.
•With an operator sitting or riding on the PartsCaddyLite.
•With added weight not...