Aimco Brakes Freedom3 LAB User Manual

 
 
   [email protected]     
31  
 
Fast. Torque + Angle is a tightening strategy used in production line. Operator must set 
nominal angle, tolerances and the torque window (min, max e nominal torque).After getting a 
specific torque ( angle threshold, must be set in the test strategy), user must continue to tighten 
getting windows tolerance angle. Freedom³ will give as a main results for the statistic the angle 
and torque values  and it will show both graphs.  Also FREEDOM³ will check if the...

 
32 
 
32 Freedom³ LAB mode 
 
 
Fast. Yield is tightening strategy used in production line. Operator must set nominal torque  
and nominal angle with both tolerances. During the tightening when the joint gets the yield point, 
Freedom³ will collect as results torque and angle values at yield point and it will show both 
statistic graphs. If the torque or angle values are outside from tolerance windows, the tightening 
status will be Not OK (NOK).  
 
 
 
See below to program Freedom³ for “Fast. Yield”...

 
 
   [email protected]     
33  
Fast. Yield + angle is a tightening strategy used in production line. Operator must set 
nominal torque  and nominal angle with both tolerances. During the tightening, when the joint 
gets the yield point, user must over tighten the joint till arrive to the angle tolerance set in the 
test. Freedom³ will collect as results torque and angle values at pick point and it will show both 
statistic graphs. If the torque or angle values are outside from tolerance windows,...

 
34 
 
34 Freedom³ LAB mode 
Note:  
Yield.Det.Ang is an angle parameter, for default is 3°, that means Freedom³ checks every 3° the 
gradient of the curve to recognize the Yield point. If the joint is more soft, we suggest to increase 
Yield.Det.Ang . 
The Angle value at Yield Point is the angle between  “Start torque” and “Yield point” 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

 
 
   [email protected]     
35  
Test Field Table Description  
 
 
 
In the table below is explained the mining of all fields to fill, in order to run tests with Freedom³. 
Touch the correspondent screen button to enable the field:  
 
 
Field Meaning 
Description This field is used to describe the test in order to 
easily identify it. 
Test Type Is the test to run, there are different typologies 
of test: quality , SPC, Production See previous 
paragraph for the meaning of every test or 
tightening...

 
36 
 
36 Freedom³ LAB mode 
 
Field Meaning 
Tool (Tool Extra Lenght. – Tool ACC) Torque Coefficient is a correction factor used 
when an extension  is mounted on the wrench 
and it modifies the original length used to 
certify and calibrate the wrench (let “0” if there 
is not any extension).  
Tool Angle Correction Coefficient is a 
parameter used when an long extension is 
mounted on wrench or rotary transducer, to 
compensate the torsion of extension, 
otherwise it will introduce an error in the...

 
 
   [email protected]     
37  
 
 
 
 
 
Example of Quality Test 
 
Freedom³ opens “Brk Peak” test window: 
 
 
 
 
 
 
 
  

 
38 
 
38 Freedom³ LAB mode 
Freedom³ is waiting for starting  test. Selecting “Brk Test” user has to over-tightening as much as 
necessary, at the end of over-tightening, if the result is “OK” Freedom³ will display: 
 
 
 
 
 
 
 
In case of test not OK: 
 
 
 
 
  

 
 
   [email protected]     
39  
If the result value are outside from tolerances, Freedom³ will ask to confirm the result or to repeat 
the test (it’s possible to disable this function by setup, see “Setup LAB mode” paragraph). There is 
not limit, user can have all test he wants (Free Test), there is not any group to complete like in SPC 
test. 
 
Press “ESC” when the test is finish and FREEDOM³ will go back to Free Test page. To see Curves 
and result, once selected the test, press the right arrow...

 
40 
 
40 Freedom³ LAB mode 
It will appear a new window where is possible select Curves (torque/time or torque/angle) or 
value chart. See fig. below: 
 
 
 
 
 
->Selecting “Curve Torque/Time” and pressing confirm(“V” on Freedom³ keyboard), Freedom³ will 
display Torque/Time curve: 
 
 
 
 
 
By left and right arrows of Freedom³ keyboard is possible to move the cursor and analyze the 
curve step by step.