Alarm Lock ALDTMIII SETUP CONFIGURATION INSTRUCTIONS User Manual

							AL-DTM-III   
 
SETUP & CONFIGURATION INSTRUCTIONS 345 Bayview Avenue 
Amityville, New York 11701 
For Sales and Repairs, (800) 645-9445 
For Technical Service, (800) 645-9440 
© ALARM LOCK 2005    Publicly traded on NASDAQ    Symbol: NSSC WI1443  8/05 
ALARM LOCK 
AL-DTM-III Setup 
Configure the internal DTM software for DTM-III op-
eration: 
 
1.     From  the Power On or PC Comm. mode, press and 
HOLD both the left and green buttons on the DTM.  
After several messages appear, release the buttons 
when the display reads: 
 
 
 
2.     When  the  display  reads  CONFIG. LANGUAGE, the 
DTM has entered its configuration and self-test 
mode.   
3.     Press and release the green button once and the dis-
play will read CONFIG FOR DTM-III MODE.   
4.     Press  and HOLD the green button until the DTM 
beeps and the following text appears: 
 
 
 
 
        The  top  line  of  the  display  indicates  that  DTM-III 
mode is currently off; the bottom line corresponds to 
the three buttons on the DTM. 
        Therefore,  to  activate  DTM-III  operation,  press  the 
left button.  The top line of the display will now read: 
 
 
 
 
(Note:  If using DL-Windows versions earlier than 
3.5.1, you must press the center button to keep 
DTM-III operation off--thus retaining DTM-II opera-
tion).   
 
5.    Press the green button to exit this sequence.  TASK 
ENDING! will appear briefly.  The DTM will proceed 
directly to Door Selection Mode as described in the 
next section. 
 
 
Door Selection Mode 
Door Selection Mode is only needed if performing 
initial lock programming using DL-Windows 3.5.1.  
See the DL-Windows Users Guide OI237 for more 
information about Door Selection Mode.   
1.    When configuring to allow Door Select Mode, the dis-
play will switch between the following: 
 
 
 
2.     Press  and HOLD the green button until the DTM 
beeps.  The DTM will display: 
 
 
 
       The top line of the display indicates that Door Select 
mode is currently off; the bottom line corresponds to 
the three buttons on the DTM. 
       Therefore, if using DL-Windows Version 3.5.1 or later 
and you wish to use the AL-DTM-III to provide initial 
programming to currently installed locks, press the 
left button to turn DOOR SELECT on.  The top line of 
the display will now read: 
 
 
 
(Note:  If using DL-Windows Version 3.5.1 or earlier, 
you must press the center button to keep Door Se-
lect mode off.  See the DL-Windows User Guide for 
details regarding Door Select mode).   
 
5.   Press and release the green button until the DTM 
Displays: 
 
 
 
6.   Press and hold the green button until the DTM 
Beeps.  The DTM will perform a brief power control 
test (TEST RUNNING!) and then shut down within 5 
seconds. 
DTM-III MODE=OFF 
ON    OFF   EXIT 
ENTERING  
CONFIG/TEST MODE Release the 
buttons when 
displayed 
DTM-III MODE=ON 
ON    OFF   EXIT 
DOOR SELECT= OFF 
ON    OFF   EXIT 
CONFIG. DOOR 
SELECT MODE Hold Button=Run, 
Press=Next Test 
DOOR SELECT=  ON 
ON    OFF   EXIT 
Sleep Then 
Power Down. 
Data Transfer Modules allow the transfer of lock programs and other data between DL-Windows software and Alarm Lock locking de-
vices.  The improved DTM-III allows for more locks to be stored per account, both within DL-Windows and within the DTM-III itself.  These 
instructions will allow you to configure for the improved DTM-III operation.   
DTMs that start up with the message Alarm Lock DTM-II-III, V1.XX will operate in both the DTM-II and DTM-III modes.  Units 
configured to operate in DTM-III mode will display DTM-III when prompting users to enter lock mode.  The DTM-III mode is required for 
DL-Windows 3.5.1 operation, and likewise DL-Windows 3.5.1 is required for use with DTM-III mode.  Note:  If you are unsure about your 
version of DL-Windows, version numbers can be found in the DL-Windows Help, About screen.  Products shipped as DTM-III have been 
factory configured for DTM-III mode ON and Door Select Mode OFF.    
						

							ALARM LOCK SECURITY SYSTEMS, INC. (ALARM 
LOCK) warrants its products to be free from 
manufacturing defects in materials and workmanship for 
24 months following the date of manufacture. ALARM 
LOCK will, within said period, at its option, repair or 
replace any product failing to operate correctly without 
charge to the original purchaser or user. 
This warranty shall not apply to any equipment, or 
any part thereof, which has been repaired by others, 
improperly installed, improperly used, abused, altered, 
damaged, subjected to acts of God, or on which any 
serial numbers have been altered, defaced or removed. 
Seller will not be responsible for any dismantling or 
reinstallation charges. 
THERE ARE NO WARRANTIES, EXPRESS OR 
IMPLIED, W HICH EXTEND BEYOND THE 
DESCRIPTION ON THE FACE HEREOF. THERE IS 
NO EXPRESS OR IMPLIED WARRANTY OF 
MERCHANTABILITY OR A WARRANTY OF FITNESS 
FOR A PARTICULAR PURPOSE. ADDITIONALLY, 
THIS WARRANTY IS IN LIEU OF ALL OTHER 
OBLIGATIONS OR LIABILITIES ON THE PART OF 
ALARM LOCK. 
Any action for breach of warranty, including but not 
limited to any implied warranty of merchantability, must 
be brought within the six months following the end of the 
warranty period.  
IN NO CASE SHALL ALARM LOCK BE LIABLE TO 
ANYONE FOR ANY CONSEQUENTIAL OR 
INCIDENTAL DAMAGES FOR BREACH OF THIS OR 
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, 
EVEN IF THE LOSS OR DAMAGE IS CAUSED BY 
THE SELLERS OW N NEGLIGENCE OR FAULT. 
In case of defect, contact the security professional 
who installed and maintains your security system. In 
order to exercise the warranty, the product must be 
returned by the security professional, shipping costs 
prepaid and insured to ALARM LOCK. After repair or 
replacement, ALARM LOCK assumes the cost of 
returning products under warranty. ALARM LOCK shall 
have no obligation under this warranty, or otherwise, if 
the product has been repaired by others, improperly 
installed, improperly used, abused, altered, damaged, 
subjected to accident, nuisance, flood, fire or acts of 
God, or on which any serial numbers have been altered, 
defaced or removed. ALARM LOCK will not be 
responsible for any dismantling, reassembly or 
reinstallation charges. 
This warranty contains the entire warranty. It is the 
sole warranty and any prior agreements or 
representations, whether oral or written, are either 
merged herein or are expressly canceled. ALARM LOCK 
neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to 
assume for it, any other warranty or liability concerning 
its products. 
In no event shall ALARM LOCK be liable for an 
amount in excess of ALARM LOCKs original selling 
price of the product, for any loss or damage, whether 
direct, indirect, incidental, consequential, or otherwise 
arising out of any failure of the product. Sellers warranty, 
as hereinabove set forth, shall not be enlarged, 
diminished or affected by and no obligation or liability 
shall arise or grow out of Sellers rendering of technical 
advice or service in connection with Buyers order of the 
goods furnished hereunder. 
ALARM LOCK RECOMMENDS THAT THE ENTIRE 
SYSTEM BE COMPLETELY TESTED WEEKLY. 
Warning: Despite frequent testing, and due to, but not 
limited to, any or all of the following; criminal tampering, 
electrical or communications disruption, it is possible for 
the system to fail to perform as expected. ALARM LOCK 
does not represent that the product/system may not be 
compromised or circumvented; or that the product or 
system will prevent any personal injury or property loss 
by burglary, robbery, fire or otherwise; nor that the 
product or system will in all cases provide adequate 
warning or protection. A properly installed and 
maintained alarm may only reduce risk of burglary, 
robbery, fire or otherwise but it is not insurance or a 
guarantee that these events will not occur. 
CONSEQUENTLY, SELLER SHALL HAVE NO 
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY 
DAMAGE, OR OTHER LOSS BASED ON A CLAIM 
THE PRODUCT FAILED TO GIVE WARNING. 
Therefore, the installer should in turn advise the 
consumer to take any and all precautions for his or her 
safety including, but not limited to, fleeing the premises 
and calling police or fire department, in order to mitigate 
the possibilities of harm and/or damage. 
ALARM LOCK is not an insurer of either the property 
or safety of the users family or employees, and limits its 
liability for any loss or damage including incidental or 
consequential damages to ALARM LOCKs original 
selling price of the product regardless of the cause of 
such loss or damage. 
Some states do not allow limitations on how long an 
implied warranty lasts or do not allow the exclusion or 
limitation of incidental or consequential damages, or 
differentiate in their treatment of limitations of liability for 
ordinary or gross negligence, so the above limitations or 
exclusions may not apply to you. This Warranty gives 
you specific legal rights and you may also have other 
rights which vary from state to state. 
ALARM LOCK LIMITED WARRANTY