Alarm Lock DL1200Narrow Stile Programming Instructions User Manual

							1 
CONGRATULATIONS!    
Your new DL1200 Alarm Lock Trilogy electronic digital lock is a manually 
programmable narrow stile entry trim for Adams Rite® 4710, 4730 and 
4900 deadlatch locks, and 1850, 1950, 4070, MS1850S and MS1950S 
series deadbolts for narrow stile aluminum doors*.  The DL1200 is a rug-
ged entry lock of advanced design with several programmable features.  
Three security levels are provided:  Master (can perform ALL functions), 
Manager (can perform MOST functions plus entry), and Basic User 
(entry only).   
 
The lock includes 100 User Codes (consisting of Managers and Basic 
Users), plus three one-time entry Service Codes.  
The Manager/Basic User Codes are organized 
similar to a grid--ten banks of ten Access Codes.   
 
Take the time to read through this guide to familiar-
ize yourself with the features and operations of the 
lock, and its quick and easy programming proce-
dures. 
 
Features 
•1 Master Code (all functions including entry) 
•10 Manager Codes (perform SOME programming 
functions plus entry) 
•90 Basic User Access Codes (Entry Only) 
•3 Service Codes (One-Time Entry Codes) 
•Two User Disable Modes: 
•All User Codes Disabled Except Master Code 
•All User Codes in a Bank Disabled Except 
Manager Codes 
•30-Second Keypad Anti-Tamper Lockout: 
(Keypad Lockout After 3 Unsuccessful User Code 
Entries) 
 
Trilogy 
DL1200 
Programming Instructions
 
OI310  11/05 
345 Bayview Avenue 
Amityville, New York 11701 
For Sales and Repairs 1-800-ALA-LOCK 
For Technical Service 1-800-645-9440 
© ALARM LOCK 2005 
 
 
QUICK LOOKUP  Wiring .................................................................2 
Quick Start ........................................................2 
Testing Codes ....................................................3 
Manager & User Location Worksheet ................4 
Manager & User Location  Example ..................5 
Programming Worksheet: Functions ..................6 
Change Existing Master Code .......................7 
Add/Change Manager Codes ........................7 
Add/Change User Codes ..............................7 
Deleting Codes ..............................................7 
Disable/Enable Users ....................................7 
Disable/Enable All .........................................8 
Code Location Function ................................8 
Next Free Code Address Locator ..................8 
Add/Delete Service Codes  ...........................9 
Enable/Disable Passage Mode .....................9 
Pass Time (Door Unlock) ............................9 
Disable/Enable Groups .................................9 
Disable/Enable Users in Bank .....................10 
Keypress Sound Options .............................10 
Audible and LED Indications ............................10 
Battery Replacement ........................................11 
Erase All Programming ....................................11 
Limited Warranty ..............................................12 
 
DL1200 
*Adams Rite Manufacturing Co., Pomona, CA.  www.adamsrite.com 
All products, product names and services described in this manual are for identification 
purposes only and may be trademarks of their respective companies.  
						

							2 
Quick Start 
First Time Start Up 
1.  Unpack the lock from its factory packaging. 
2.  Connect the battery pack.   
3.  Listen for 3 beeps.  The lock is now ready to accept programming.  Note:  Failure to follow this exact proce-
dure can result in erratic lock behavior.   
 
       Important  Note:   When entering any key sequence below, do not pause more than 5 seconds between any 
key presses--otherwise you must start again.  (Note:  If you wish, this 5-second delay between key presses 
can be extended--see Pass Time on page 9 after completing this section). 
       No other programming commands will be accepted until the Factory Master Code has been changed. 
 
Change Factory Master Code 
The Master Code is a secret code (entered at the keypad) that allows you to change ALL programming functions 
and options.  Because all locks are manufactured identically (and leave the factory with the same Master Code), 
this factory Master Code is not very secret--and MUST be changed to your own personal Master Code to ensure 
security.  A 5 digit Code is recommended. 
 
1.  Press the factory Master Code:  1 2 3 4 5.  A beep will sound and the lock will open (if the 
lock does not unlock, refer to section Erase All Programming on page 11). 
2.  Within 5 seconds, press 
; 1 ;. 
3.  Within 5 seconds, enter a new Master Code.  This new Master Code may consist of 3 to 5 digits*, however, the 
number selected determines the number required for all subsequent Manager and User Access Codes.  
4.   Press 
;. 
5.  Re-enter the new Master Code again to validate.  A 6-beep acknowledgement (with a red LED) will sound.  
Wait 5 seconds for lock to re-lock. 
6.  Test the new Master Code.  Enter the new Master Code; a beep will sound and the lock will unlock.  Now that 
the Master Code has been changed, there is no need to change it again (unless you want to).   
 
For example, if you want your new Master Code to be 44444, press: 
1 2 3 4 5   ; 1 ;   44444  ;  44444. 
 
If you wish, write your new Master Code in the spaces provided: 
1 2 3 4 5   ; 1 ;   ____ ____ ____ ____ ____ ; ____ ____ ____ ____ ____  
 
 
 
(Write your new Master Code) (Repeat) 
* Once the number of digits is selected, it cannot be changed unless all programming is erased and the Factory Default settings are re-loaded 
using the Erase All Programming, Alternative Method procedure found on page 11. 
Wiring: 
See the Installation Instructions for more information. 
 
Batteries: 
Use only two 123 Type Lithium batteries (Duracell 
P/N CR17345). 
Wiring 
(Continued)  
						

							3 
Quick Start (cont’d) 
Enter a Manager Code 
Manager Codes are located at locations 00, 10, 20, 30, 40, 50, 60, 70, 80, and 90 (see grid on page 4).  Note:  
New Manager Codes MUST use the same number of digits as the (new) Master Code.  Enter as follows.   
1.   Press the (new) Master Code. 
2.   Press 
; [press a Manager location i.e. 00, 10, 20, 30, 40, 50, 60, 70, 80, or 90] ;.  
3.  Press a new Manager Code using the same number of digits as the (new) Master Code
.  A 6-beep acknowl-
edgement (with a red LED) will sound.  Wait 5 seconds for lock to re-lock. 
For example, if you want to add a Manager Code of 33333 in location 00, 
[Press the (new) Master Code]   
; 00 ;   33333. 
4.   If lock remains open, repeat from step 2; otherwise restart from step 1 for each new Manager Code. 
 
Enter Basic User Access Codes 
See the grid on page 4 for more information regarding User locations.  You can choose to enter your User Codes 
in many possible locations, and in any order you wish.  User Codes do not have programming privileges (entry 
only).  Duplicate User Codes are not allowed. 
1.   Press the (new) Master Code or associated Manager Code. 
2.   Press 
; [press a 2-digit location number] ;. 
3.  Press a new User Access Code using the same number of digits as the (new) Master Code
.  A six-beep ac-
knowledgement (with a red LED) will sound.  Wait 5 seconds for lock to re-lock.  The new User Access Code is 
now entered in that location number. 
For example, if you want to add a User Access Code of 22222 in User Number 01, press: 
[(New) Master Code] 
; 01 ;   22222. 
4.   If lock remains open, repeat from step 2; otherwise restart from step 1 for each new User Access Code. 
 
Delete a User Access Code 
The Master Code cannot be deleted.  Manager Codes can only be deleted with the Master Code.  If the location 
(User Number) of the Code is unknown, use the Code Location Function (page 8). 
1.   Press the (new) Master Code or Manager Code. 
2.   Press 
; [press the 2-digit location number] ; :.  A six-beep acknowledgement (with a red LED) will 
sound.  Wait 5 seconds for lock to re-lock.  The User Access Code is now deleted. 
For example, if you want to delete a User Access Code located in location 47, press: 
[(New) Master/Manager Code] 
; 4 7 ;   :. 
3.  If lock remains open, repeat from step 2; otherwise restart from step 1 for each User Access Code you want to 
delete. 
VALID CODE - The Green LED will flash (with 1 beep) after a valid code is entered.  The lock will unlock immediately and 
remain unlocked for about 5 seconds (this unlocked time is the Pass Time).  To make the Pass Time longer or 
shorter, use the Pass Time Function on page 9.  Note:  While the lever or knob may be rotated at any time, the latch 
will not be engaged to unlock the door unless a valid User Access Code is entered at the keypad. 
 INVALID CODE - The Red LED will flash 5 times (with 5 beeps) after an invalid code is entered.  (To quickly clear an invalid 
User Access Code, press 
; and immediately re-enter the correct Code).    KEYPAD ANTI-TAMPER LOCKOUT - If 3 invalid User Access Codes are entered in succession, the lock will turn off for 
approximately 30 seconds to prevent tampering.  The DL1200 will emit 2 beeps with a Red LED flash warning at the 
end of the anti-tamper period.  The lock will exit Anti-Tamper mode in 30 seconds or upon activation of the Remote 
Switch Input (white wires).  Note:  The lock will go into Anti-Tamper after 3 unsuccessful Code entries even if entered 
by different users and spaced apart in time.  Therefore, the lock may “appear” to go into Anti-Tamper Lockout even 
after the entry of just one invalid User Access Code. 
Testing Codes  
						

							4 
The DL1200 lock provides three security levels:  Master (can perform ALL functions), Manager (can perform SOME program-
ming functions plus entry), and Basic User (entry only).  In total, there are 104 locations inside the DL1200 lock:  one Master 
Code, 10 Manager and 90 User Access Codes, and three one-time entry Service Codes.  Where the Access Code is located 
will determine its security level.  From the factory, all locations (except for the Master Code) are empty; each location can then be 
programmed to contain an Access Code, and these Access Codes enable Users to program and/or unlock the lock.  As a visual 
aid, the 100 Manager/User Access Code locations are detailed in the grid below, with ten Banks (columns) of ten Managers/
Users (rows).  Each of the 100 squares in the grid is identified by a unique two-digit location (00) through (99).  Notice that these 
two digits also specify its Bank (column) and Manager/User (row) location in the grid.  Also notice that all Managers are in the top 
row, their locations all ending in a zero (locations 00, 10, 20, 30 and so on through 90).  Note:  Use the blank grid below as a Pro-
gramming Worksheet for preparing all programming in advance.  Store this worksheet in a safe place for future reference. 
Manager & User Location Worksheet 
 
MANAGERS 
→ MGR 10 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 20 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 30 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 40 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 50 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 60 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 70 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 80 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 90 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 11  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 21  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 31  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 41  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 51  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 61  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 71  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 81  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 91  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 12  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 22  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 32  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 42  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 52  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 62  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 72  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 82  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 92  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 13  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 23  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 33  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 43  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 53  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 63  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 73  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 83  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 93  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 14  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 24  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 34  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 44  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 54  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 64  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 74  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 84  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 94  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 15  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 25  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 35  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 45  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 55  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 65  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 75  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 85  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 95  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 16  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 26  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 36  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 46  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 56  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 66  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 76  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 86  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 96  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 17  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 27  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 37  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 47  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 57  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 67  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 77  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 87  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 97  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 18  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 28  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 38  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 48  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 58  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 68  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 78  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 88  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 98  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 
USERS 
→ USER 19  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 29  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 39  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 49  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 59  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 69  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 79  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 89  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 99  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
MGR 00  
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 01  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 02  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 03  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 04  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 05  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 06  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 07  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 08  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
USER 09  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
_ _ _ _ _ 
 BANK 0 BANK 1 BANK 2 BANK 3 BANK 4 BANK 5 BANK 6 BANK 7 BANK 8 BANK 9 
Each square represents a location inside the lock (excluding the Master Code and the 3 Service 
Codes).  Each location can hold one User Access Code which can unlock the lock. 
SERVICE CODE 1 SERVICE CODE 2 SERVICE CODE 3 MASTER CODE 
LOCK DESCRIPTION  
						

							5 
User Access Codes allow access only; Manager Codes allow more:  Manager Codes have the ability to program and delete 
User Access Codes within that Managers Bank (column).  The DL1200 lock can hold up to 10 Manager Codes, one for 
each Bank (locations (00), (10), (20), (30), (40), (50), (60), (70), (80), (90)), and are all found at the top row of the grid be-
low.  Note:  Only the Master Code can add or delete a Manager Code. 
 In addition, Managers not only possess programming abilities for User Access Codes residing in their own Bank, but also 
for all higher Banks until the next programmed Manager Code appears.   
 For example (see shaded grid below), if Manager Codes are programmed for locations (00) and (60), then the Manager in 
location (00) has control of the gray-shaded locations (00-09, 11-19, 21-29, 31-39, 41-49, and 51-59).  The Manager in lo-
cation (60) then has control over the black-shaded locations (61-69, 71-79, 81-89, and 91-99).   
 Note:  If you wish to grant any Manager the ability to program any User, use the Disable Groups Function on page 9 
(Enter the Master Code, then press 
; 211 ;).   
Manager & User Location Example 
Manager Location Example 
 
MANAGERS 
→ MGR 10 (BLANK) MGR 20 (BLANK) MGR 30 (BLANK) MGR 40 (BLANK) MGR 50 (BLANK) MGR 60 MGR 70 (BLANK) MGR 80 (BLANK) MGR 90 (BLANK) 
 
USERS 
→ USER 11 
 USER 21 
 USER 31 
 USER 41 
 USER 51 
 USER 61 
 USER 71 
 USER 81 
 USER 91 
 
 
USERS 
→ USER 12 
 USER 22 
 USER 32 
 USER 42 
 USER 52 
 USER 62 
 USER 72 
 USER 82 
 USER 92 
 
 
USERS 
→ USER 13 
 USER 23 
 USER 33 
 USER 43 
 USER 53 
 USER 63 
 USER 73 
 USER 83 
 USER 93 
 
 
USERS 
→ USER 14 
 USER 24 
 USER 34 
 USER 44 
 USER 54 
 USER 64 
 USER 74 
 USER 84 
 USER 94 
 
 
USERS 
→ USER 15 
 USER 25 
 USER 35 
 USER 45 
 USER 55 
 USER 65 
 USER 75 
 USER 85 
 USER 95 
 
 
USERS 
→ USER 16 
 USER 26 
 USER 36 
 USER 46 
 USER 56 
 USER 66 
 USER 76 
 USER 86 
 USER 96 
 
 
USERS 
→ USER 17 
 USER 27 
 USER 37 
 USER 47 
 USER 57 
 USER 67 
 USER 77 
 USER 87 
 USER 97 
 
 
USERS 
→ USER 18 
 USER 28 
 USER 38 
 USER 48 
 USER 58 
 USER 68 
 USER 78 
 USER 88 
 USER 98 
 
 
USERS 
→ USER 19 
 USER 29 
 USER 39 
 USER 49 
 USER 59 
 USER 69 
 USER 79 
 USER 89 
 USER 99 
 
MGR 00 
USER 01 
 
USER 02 
 
USER 03 
 
USER 04 
 
USER 05 
 
USER 06 
 
USER 07 
 
USER 08 
 
USER 09 
 
 (BANK 0) (BANK 1) (BANK 2) (BANK 3) (BANK 4) (BANK 5) (BANK 6) (BANK 7) (BANK 8) (BANK 9) 
Manager Code 
Programmed here Manager Code 
Programmed here  
						

							6 
Programming Worksheet:  Functions 
FUNCTION PRESS THESE BUTTONS ON KEYPAD 
Change Existing Master Code [Enter Factory or Existing Master Code] ;1; [Enter New Master Code _ _ _ _ _ ] ;  
[Re-enter New Master Code _ _ _ _ _ ] [6 beeps = OK] 
Add/Change Manager Codes (up to 10) [Enter Master Code] ; [Enter 2-digit Manager Location _ _ ] ; 
     [Enter new Manager Code _ _ _ _ _ ] [6 beeps = OK] 
Add/Change User Codes (up to 90) Press Master or Manager Code ; [Enter 2-digit Location _ _ ] ; [Enter new User Code _ _ _ _ _ ] 
[6 beeps = OK] 
Deleting Manager & User Codes Press Master or Manager Code ; [Enter Bank Number] [Enter User Number] ;: 
Disable User Number Press Master or Manager Code ; [Enter Bank Number] [Enter User Number] ; 
Enable User Number Press Master or Manager Code ; [Enter Bank Number] [Enter User Number] ; 
Disable All Press Master or Manager Code ; 9 5 5 ;  (Reset with Function 944) 
Enable All Press Master or Manager Code ; 9 4 4 ; 
Disable Users Only Press Master or Manager Code ; 9 5 0 ;  (Reset with Function 944) 
Code Location Function Press Master or Manager Code ; 6 ; [Enter Code to be located] 
Next Free Code--Address Locator Press Master or Manager Code ; 7 ; [Responds with Bank # and User #]  
Service Code 1 Press Master or Manager Code ; 3 0 1 ; [Enter new Service Code _ _ _ _ _ ] 
Service Code 2 Press Master or Manager Code ; 3 0 2 ; [Enter new Service Code _ _ _ _ _ ] 
Service Code 3 Press Master or Manager Code ; 3 0 3 ; [Enter new Service Code _ _ _ _ _ ] 
Clear Service Codes Press Master or Manager Code ; 3 0 0 ; 
Enable Passage Mode Press Master or Manager Code ; 4 ;  
Disable Passage Mode Press Master or Manager Code ; 5 ; 
Pass Time (Door Unlock) Press Master Code ; 4 [Enter 02 - 20 seconds] ; 
Enable Groups Press Master Code ; 2 1 0 ; 
Disable Groups Press Master Code ; 2 1 1 ; 
Disable Users In Bank Press Master or Manager Code ; 8 5 [Enter Bank Number (0-9)] ; 
Enable Users in Bank Press Master or Manager Code ; 8 4 [Enter Bank Number (0-9)] ; 
High Freq KP Feedback + Led Press Master Code ; 2 2 0 ; 
Low Freq KP Feedback + Led Press Master Code ; 2 2 1 ; 
Click!  KP Feedback + Led Press Master Code ; 2 2 2 ; 
Led Only  Press Master Code ; 2 2 3 ; 
Erase All Programming Press Master Code ; 0 0 0 ; [Listen for 6 beeps = OK] 
Directions:  The Factory Master Code (1-2-3-4-5) must first be reprogrammed as a new Master Code before any other programming 
can take place.  All new Access Codes must have the same number of digits as the new Master Code.  Choose new Access Codes 
and write them in spaces provided (in pencil) before programming the lock.  6 beeps will usually be heard after an acceptable entry. 
Note:  Managers do not have the ability to add/delete/enable/disable Users outside their Bank, unless Groups are disabled.  
						

							7 
Change Existing Master Code*  ; 1 ; 
[ __ __ __ __ __ ]   ; 1 ;     [ __ __ __ __ __ ] ;    [ __ __ __ __ __ ] 
Old (or Factory) Master Code                                           New Master Code*                   Confirm New Master Code* 
For new locks, follow the Quick Start on page 2. 
Programming Functions 
* Once the number of digits is selected, it cannot be changed unless all programming is erased and the Factory Default settings are re-loaded 
(power must be removed and re-applied as per the Erase All Programming procedure found on page 11. 
** Required only if DL1200 is locked. 
Add/Change User Codes  ; [ __ __ ] ; 
Follow the Quick Start on page 3.   
[ __ __ __ __ __ ]   ; [ __ __ ] ;   [ __ __ __ __ __ ] 
       Master Code or                                                                       New User Code 
       Manager Code** Bank (Column) 
0-9 User (Row) 
1-9 
Add/Change Manager Codes  ; [ __ ] 0 ; 
Follow the Quick Start on page 3.  Note:  You can also add/change the Manager Code in location 
00 by entering the Master Code, 
; 2 ; then the new Manager Code.   
[ __ __ __ __ __ ]   ; [ __ ] 0 ;   [ __ __ __ __ __ ]  
           Master Code**                                                                      New Manager Code 
User (Row) Always zero for Managers Manager Bank (Column) 0-9  
Deleting Manager & User Codes  ;  [ _ _ ] ; : 
Follow the Quick Start on page 3.   
[ __ __ __ __ __ ]   ;   [ _ _ ]  ;  :    
   
Master or Manager Code** 
User (Row) Always zero for Managers 
0-9 Manager Bank (Column) 
0-9 
Disable/Enable Users  
Enter the Master Code to disable/enable any Manager or User, or enter a Manager Code to disable any User 
within the Managers Bank.   
Disable User Number [ __ __ __ __ __ ]    ;    [ __ __ ]    ; (Allow system to relock) 
  Master or Manager Code                   Bank/User Number 
Enable User Number [ __ __ __ __ __ ]    ;    [ __ __ ]    ; (Allow system to relock) 
  Master or Manager Code                   Bank/User Number  
						

							8 
Programming Functions (contd) 
Disable All:  If Master Code is used, disables all 100 User\Manager Codes and clears all 3 Service Codes.  If 
a Manager Code is used, disables all Users (even across multiple Banks) under that Manager.   
Disable Users Only:  If Master Code is used, disables all 90 Users and clears all 3 Service Codes, while Manag-
ers remain active.  If a Manager Code is used, disables all Users (even across multiple banks) under that Man-
ager. 
Enable All:  If Master Code is used, re-enables all 100 User/Manager Codes (Service Codes must be re-
programmed).  If a Manager Code is used, re-enables all Users (even across multiple Banks) under that Man-
ager.  Note:  Managers cannot disable themselves.  Use Function 944 to restore Functions 955 and 950.  In 
addition, if Codes are disabled using Function 955 or 950, and a new User Code is subsequently added (or an 
existing Code changed), the new (or changed) User Code will automatically become enabled. 
Enable/Disable All  
Disable All  [ __ __ __ __ __ ] ;955; 
   Master/Manager  Code**                                                  
Enable All [ __ __ __ __ __ ] ;944; 
   Master/Manager  Code**                                                  
[ __ __ __ __ __ ] ;950; 
   Master/Manager  Code**                                                  
Disable Users Only 
Next Free Code Address Locator  ; 7 ; 
Using the same method of beeps and flashes used in the Code Location Function, and dependent on the Mas-
ter or Managers Code entered, the lock will report the next available address for User Access Code program-
ming. 
Report Sequence 
1.   At the start of the Next Free Code Location function, the lock will Flash both the GREEN and RED LEDs and will emit a low tone. 
2.   The lock will identify the Bank number by flashing the GREEN LED and beeping the sounder from 0 -9 times. 
3.   To signify the end of the Bank number ID sequence, the lock will flash both the GREEN and RED LEDs and will emit a low tone. 
4.   The lock will identify the User number by flashing the GREEN LED and beeping the sounder from 0-9 times. 
5.   To signify the end of the Code Location function, the lock will flash both the GREEN and RED LEDs and will emit a low tone.  If no free 
address is found, then the lock will emit a programming error tone sequence.  No LED flashes/sounder beeps represent the number 
zero.   
Be sure to record all Code locations in the blank worksheet (page 4) for future reference.  If the location of a Code is 
not known, use this function to find the Code.  The lock will identify the BANK (0-9) and USER (0-9) by beeping and 
flashing the GREEN LED 0 to 9 times as detailed below. 
Code Location Function  ; 6 ; 
[ __ __ __ __ __ ] ; 6 ; 
     [ __ __ __ __ __ ] 
     Master/Manager Code**                                               Code 2 - 5 digits 
If the code entered is recognized, the following sequence will occur: 1.   At the start of the Code Location sequence, the lock will Flash both the GREEN and RED LEDs and will emit a low tone. 
2.   The lock will identify the Bank number by flashing the GREEN LED and beeping the sounder from 0 -9 times. 
3.   To signify the end of the Bank number ID sequence, the lock will flash both the GREEN and RED LEDs and will emit a low tone. 
4.   The lock will identify the User number by flashing the GREEN LED and beeping the sounder from 0-9 times. 
5.   To signify the end of the Code Location function, the lock will flash both the GREEN and RED LEDs and will emit a low tone. 
      Note:   Should the Code not be recognized, the lock will sound 5 beeps with a RED LED.  When the Bank and/or slot numbers are 
zero, the GREEN LED will not flash and the sounder will not beep. 
** Required only if DL1200 is locked. 
[ __ __ __ __ __ ]    ; 7 ; 
      Master/Manager Code**  
						

							9 
[ __ __ __ __ __ ]   ; 301 ;   [ __ __ __ __ __ ]  
   Master/Manager Code**                                                                      New Service Code 
Service Codes are one-time-only Codes; once entered into the keypad, it is deleted.  Use the same Code up 
to 3 times by programming all three Service Codes with the same Code.  Note:  Service Codes are lost if 
power is removed.  To delete a single Service Code, press 
;, enter Service Code number (301, 302 or 
303), then press 
; :. 
Add/Delete Service Codes 
Service Code 1 
Service Code 2 
Service Code 3 
[ __ __ __ __ __ ]   ; 302 ;   [ __ __ __ __ __ ]  
   Master/Manager Code**                                                                      New Service Code 
[ __ __ __ __ __ ]   ; 303 ;   [ __ __ __ __ __ ]  
   Master/Manager Code**                                                                      New Service Code 
Delete All Service Codes [ __ __ __ __ __ ]   ; 300 ; 
   Master/Manager  Code** 
The Pass Time is the time the lock stays unlocked after a valid Code entry.  Use the function below to change 
the Pass Time from 02 to 20 seconds.  The Pass Time factory default is 5 seconds.  NOTE:  The Pass Time 
will also determine the amount of time allowed between keypresses during programming. 
Pass Time (Door Unlock) 
[ __ __ __ __ __ ]   ; 4 [ __ __ ] ; 
         Master Code**                                        Pass Time 
Pass Time 
Allows passage without the need to enter a Code into the keypad.   
Enable/Disable Passage Mode 
Disable Passage Mode  [ __ __ __ __ __ ]     ; 5 ;  (Normal Operation) 
   Master or Manager Code** 
Enable Passage Mode  [ __ __ __ __ __ ]     ; 4 ;  (Unlocked) 
   Master or Manager Code** 
Programming Functions (contd) 
Disable/Enable Groups 
Disable Groups:  All Managers can program all User Access Codes, regardless of Bank.  
Enable Groups:  (Factory default)  Managers restricted to controlling only those User Access Codes within 
their own Bank (column), and all following Banks until another Manager appears.  User Access Codes in 
Banks outside of that Managers Bank cannot be programmed.  
Enable Groups [ __ __ __ __ __ ]   ; 210 ; 
         Master Code**
 
[ __ __ __ __ __ ]   ; 211 ; 
         Master Code** 
Disable Groups 
** Required only if DL1200 is locked.  
						

							10 
Programming Functions (contd) 
The DL1200 is capable of emitting 1 of 4 possible keypress sounds: 
•High Frequency Keypad Feedback + Led 
•Low Frequency Keypad Feedback + Led 
•Click! Keypad Feedback + Led 
•Led Only  
[ __ __ __ __ __ ]   ; 220 ;   
           Master Code** 
High Freq KP Keypress Sound + Led 
(Default)
 
   Keypress Sound Options  
[ __ __ __ __ __ ]   ; 221 ;   
           Master Code** 
Low Freq KP Keypress Sound + Led 
[ __ __ __ __ __ ]   ; 222 ;   
           Master Code** 
Click!  KP Keypress Sound + Led 
[ __ __ __ __ __ ]   ; 223 ;   
           Master Code** 
Led Only  
Disable/Enable Users in Bank 
Enter Bank number (0-9) to Enable/Disable all Users in Bank.  Entering a disabled Code will result in an 
accented five beep error tone (indicating the User Access Code is valid but disabled).
 
Disable Users in Bank [ __ __ __ __ __ ]     ; 8 5 [ __ ] ; 
 Master/Manager Code**                                            Bank Number 
[ __ __ __ __ __ ]    ; 8 4 [ __ ]  ; 
 Master/Manager Code**                                            Bank Number 
Enable Users in Bank 
When a key is pressed, a beep will sound and a Red LED will flash.  Other indications are:  
▪  Access Granted:  1 beep and a Green LED flash.  (When Pass Time ends, the DL1200 locks with a beep and a 
Red LED flash). 
▪  Invalid Code Entered:  5 beeps and 5 Red LED flashes. 
▪  Disabled Code Entered:  5 beeps (with extended first beep) and 5 Red LED flashes. 
▪  New Access Code Accepted:  6 beeps and 6 Red LED flashes. 
▪  Programming Error:  2 sets of 5 beeps and 5 Red LED flashes. 
▪  Return from Anti Tamper Lockout:  2 beeps with a Red LED flash. 
▪  Low Battery:  High/Low sounder with flashing Red LED for 5 seconds.  (See below to replace batteries). 
 
Note:  Keypress tones may be disabled using the ; 2 2 3 ; command (see Keypress Sound 
Options, page 10). 
Audible and LED Indications 
** Required only if DL1200 is locked.