Alarm Lock DL2500 Programming Manual

DL2500-SERIES
DIGITAL LOCKSPROGRAMMING INSTRUCTIONSU L Listed: Electrically-Controlled Single-Point Lock© Alarm Lock 1992          OI171A 06/93 

2Table of Contents
Section     Page
PROGRAMMING YOUR CODES …………………………………………………...3
MASTER CODE  …………………………………………………………….…3
MANAGEMENT CODE  ……………………………………………………….4
USER CODES  …………………………………………………………….…...4
     SERVICE CODE  …………………………………………………………….…5
PROGRAMMING SPECIAL FEATURES  ..……………………………….………..5
LOCKOUTS   …………………………………………………………….……..5
  UNLOCK TIME  …………………………………………………………….…..5
  PASSAGE  …………………………………………………………….………..6
OTHER IMPORTANT INFORMATION  …………………………………………….6
USE OF MULTIPLE DIGITS...

3USER’S GUIDE TO DL2500-SERIES CODES & FEATURES
CONGRATULATIONS! Your new Alarm Lock Trilogy electronic digital lock
is a rugged entry lock of advanced design with several programmable
features. Three security levels are provided: Master, Management, and
User, the latter comprising 15 User Codes, including a 1—time entry
Service Code. Security is assured through the availability of
29,000,000 code combinations. Take the time to read through this guide
to familiarize yourself with the features and...

4validated): [5) [4) [3] [2] [1]. Six beeps will sound and lock will
relock after about five seconds.
6.Test the new Master Code. Enter: [5] [4) [3] [2) [1]. A beep will
sound and the lock will open.
Note:If only one code is required, stop here and proceed to
PROGRAMMING SPECIAL FEATURES.
MANAGEMENT CODE.
The Management Code can program any user code (but not the Master or
Management Code) or any programmable feature except the Passage
Function. It must contain the same number of digits as the Master...

5after the six beeps sound (step 3, above) repeat steps 2 and 3 as
necessary, then test all codes when done.
SERVICE CODE.
The Service Code is a one—time User Code for cleaning crews,
babysitters, etc., which erases itself immediately after use. It is
programmed as any User Code, with the Program Code AL-3-AL. If
programmed, the Service Code replaces User Code 15 (Bank 3, User
5).
PROGRAMMING SPECIAL FEATURES
LOCKOUTS.
Any single user, any bank of users, or all users may be prevented
from entry.
User...

6Entry       Time15 sec.
210 sec.
315 sec.
4 20 sec.
Table 3. Unlock Times (times approximate).
Note:To conserve battery power, keep unlock time as short as
possible.
PASSAGE.
Programming the Passage Function will maintain the DL2500 unlocked
until reprogrammed. To set the Passage Function, enter the Master
Code, then press [AL) [4] [AL]. To relock, enter the Master Code, then
press [AL] [5) [AL].
OTHER IMPORTANT INFORMATION
USE OF MULTIPLE DIGITS.
When programming entry codes, digits need not be limited...

7USER CODE RECORD LOG
User No.       Description         User’s Name         Code______________Master_____________________________________________________Management_________________________________________________Service______________________________________User 1________Bank 1, User 1_______________________________User 2________Bank 1, User 2_______________________________User 3________Bank 1, User 3_______________________________User 4________Bank 1, User 4_______________________________User...

8ALARM LOCK LIMITED WARRANTY
ALARM LOCK  SYSTEMS, INC. (ALARM LOCK)
warrants its products to be free from manufacturing
defects in materials and workmanship for twelve
months following the date of manufacture. ALARM
LOCK will, within said period, at its option, repair or
replace any product failing to operate correctly without
charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any
part thereof, which has been repaired by others,
improperly installed, improperly...