Alarm Lock DL5200 Programming Manual

1 
CONGRATULATIONS!    
Your new Alarm Lock Trilogy electronic digital lock is a rugged 
double-sided entry lock of advanced design with several program-
mable features.  Three security levels are provided:  Master (can 
perform ALL functions), Manager (can perform MOST functions 
plus entry), and Basic User (entry only).   
 
The lock includes 100 User Codes (consisting of Managers and 
Basic Users), plus three one-time entry Service Codes.  The 
Manager/Basic User Codes are organized similar to a...

2 
Quick Start 
First Time Start Up 
1.  Unpack the lock from its factory packaging.  
2.  With the batteries disconnected, hold down any number key for 10 seconds and release. 
3.  Connect the batteries and--within 3 seconds--press and hold the 
; button.  After hearing 6 beeps, release 
the 
; button.  Wait 5 seconds for lock to re-lock (listen for 1 beep and red LED).  The lock is now ready to 
accept programming.  Note:  Failure to follow this exact procedure can result in erratic lock behavior....

3 
Quick Start (cont’d) 
Enter a Manager Code 
Manager Codes are located at locations 00, 10, 20, 30, 40, 50, 60, 70, 80, and 90 (see grid on page 4).  Note:  
New Manager Codes MUST use the same number of digits as the (new) Master Code.  Enter as follows.   
1.   Press the (new) Master Code. 
2.   Press 
; [press a Manager location i.e. 00, 10, 20, 30, 40, 50, 60, 70, 80, or 90] ;.  
3.  Press a new Manager Code using the same number of digits as the (new) Master Code
.  A 6-beep acknowl-
edgement...

4 
The DL5200 lock provides three security levels:  Master (can perform ALL functions), Manager (can perform SOME program-
ming functions plus entry), and Basic User (entry only).  In total, there are 104 locations inside the DL5200 lock:  one Master 
Code, 10 Manager and 90 User Access Codes, and three one-time entry Service Codes.  Where the Access Code is located 
will determine its security level.  From the factory, all locations (except for the Master Code) are empty; each location can then be...

5 
User Access Codes allow access only; Manager Codes allow more:  Manager Codes have the ability to program and delete 
User Access Codes within that Managers Bank (column).  The DL5200 lock can hold up to 10 Manager Codes, one for 
each Bank (locations (00), (10), (20), (30), (40), (50), (60), (70), (80), (90)), and are all found at the top row of the grid be-
low.  Note:  Only the Master Code can add or delete a Manager Code. 
 In addition, Managers not only possess programming abilities for User...

6 
Programming Worksheet:  Functions 
FUNCTION PRESS THESE BUTTONS ON KEYPAD 
Change Existing Master Code [Enter Factory or Existing Master Code] ;1; [Enter New Master Code _ _ _ _ _ _ ] ;  
[Re-enter New Master Code _ _ _ _ _ _ ] [6 beeps = OK] 
Add/Change Manager Codes (up to 10) [Enter Master Code] ; [Enter 2-digit Manager Location _ _ ] ; 
      [Enter new Manager Code _ _ _ _ _ _ ] [6 beeps = OK] 
Add/Change User Codes (up to 90) Press Master or Manager Code ; [Enter 2-digit Location _ _ ] ;...

7 
Change Existing Master Code*  ; 1 ; 
[ __ __ __ __ __ ]   ; 1 ;     [ __ __ __ __ __ __ ] ;    [ __ __ __ __ __ __ ] 
Old (or Factory) Master Code                                                New Master Code*                              Confirm New Master Code* 
For new locks, follow the Quick Start on page 2. 
Programming Functions 
* Once the number of digits is selected, it cannot be changed unless all programming is erased and the Factory Default settings are re-loaded 
(power must be removed...

8 
Programming Functions (contd) 
Disable All:  If Master Code is used, disables all 100 User\Manager Codes and clears all 3 Service Codes.  If 
a Manager Code is used, disables all Users (even across multiple Banks) under that Manager.   
Disable Users Only:  If Master Code is used, disables all 90 Users and clears all 3 Service Codes, while Manag-
ers remain active.  If a Manager Code is used, disables all Users (even across multiple banks) under that Man-
ager. 
Enable All:  If Master Code is used,...

9 
[ __ __ __ __ __ __ ]   ; 301 ;   [ __ __ __ __ __ __ ]  
    Master/Manager Code**                                                                            New Service Code 
Service Codes are one-time-only Codes; once entered into the keypad, it is deleted.  Use the same Code up 
to 3 times by programming all three Service Codes with the same Code.  Note:  Service Codes are lost if 
power is removed.  To delete a single Service Code, press 
;, enter Service Code number (301, 302 or 
303), then...

10 ** Required only if DL5200 is locked. 
Programming Functions (contd) 
The DL5200 is capable of emitting 1 of 4 possible keypress sounds: 
•High Frequency Keypad Feedback + LED 
•Click! Keypad Feedback + LED 
•LED Only  
[ __ __ __ __ __ __ ]   ; 220 ;   
           Master Code** 
   Keypress Sound Options  
[ __ __ __ __ __ __ ]   ; 222 ;   
           Master Code** 
[ __ __ __ __ __ __ ]   ; 223 ;   
           Master Code** 
High Freq KP Keypress Sound + LED 
(Default)
 
Click!  KP Keypress Sound +...