Baumatic Br23 8a Instruction Manual

Positioning 
 
o It is advisable that your appliance is only installed in a location 
where the ambient temperature of  the room, corresponds with 
the climate classification that is st ated on the rating plate of your 
appliance. Your appliance may not function correctly if the 
ambient temperature falls outs ide of the following ranges. 
 
Climate classification Appropriate ambient temperature 
SN +10 to +32 degrees centigrade 
N +16 to +32 degrees centigrade 
 
o Your appliance should not be located...

Aperture and appliance dimensions 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2) Figure 2 shows the aperture size th at you will need to be able to 
install your appliance. 
o  The appliance must be stood on a level floor. You can use the 
leveling feet to take into ac count any minor unevenness in 
the floor. 
 
 
Supplied installation components 
 
a)  Top fixing bar 
b) Sealing strip 
c) Door slider 
d)   Door guide 
e)   Fixing screws (Ø4 x 17) 
f)  Fixing screws (Ø4.2 x 9.5)...

Installing your fridge freezer 
 
If you need the appliance door to open from the 
other side, then please reverse the door before 
commencing the installation process.  (See Reversing 
the door section). 
 
 
 
  23 
 
5)  Cut the sealing strip so that is the same height as the height of the 
4) Insert the top fixing bar 
( a ) into the slot on the top of 
the appliance. Use the Ø4.2 x
9.5 fixing screws ( f) to fit the
fixing bar to the top of the 
appliance. 
 
o  Pass the power 
cable through to the...

 
 
 24
ppliance, 
. 
x the front feet into position using 
 )  Screw the top fixing bar to 
 
 
 
 
 
 
6)  Align the front feet of the a
with the front edge of the kitchen unit
 
Fi
the Ø4 x 17 fixing screws ( e). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
7
the underneath of the kitchen 
unit using the Ø4 x 17 fixing 
screws ( e). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 25
) 
Using the Ø4 x 17 fixing screws ( e), 
 
 
 
o  Open the furniture door  and the appliance door to their fullest 
positions. Both of the doors should  still be in contact with each 
other. 
8
secure the central support bracket ( g) to
the appliance and then to the kitchen 
cabinet. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9a)  Fit the door guides ( d) to the appliance doors but do not secure 
them at this stage.  Perform the following st eps on one appliance
door...

 26
 
o  s 
 furniture door. 
s the thickness of the cabinet wall + 10 
mm. This is where the e dge of the door slide (c) should be 
  o   
 door slide should be 
placed on the second pencil mark  that you made and in line with 
 
9b)  I
Ø4.2  s (f), secure the door guides ( d) to the 
ppliance door, through the predrilled hole. 
 almost 
e ( d) should not come 
past the outer edge of the door slide ( c). If it does, then your 
 
 
 
Using a pencil, mark where the edge of the appliance door meet
with...

 27
eversing the door of your appliance 
 
Caution! After unscrewi ng any of the fixing 
o  prevent it from falling 
ove from the appliance 
whilst reversing the door,  should be retained for 
later use.  
    Remove the upper hinge cover from both sides of the appliance. 
hinge screws and remove the upper  door from the middle hinge. 
  door unscrew the swing stopper 
screws an ). Fix the attached stopper 
o   it to the 
opposite side of the door (certain models only). 
o  e door from the 
bottom...

 28
 
   
   
 
o  ttom door. In case there 
is no bottom door limit peg, tran sfer the bearing (G) and washer 
o  ide of the fridge freezer proceed 
with the above procedure in reverse. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
oTilt the appliance backward at  a maximum angle of 35°. Unscrew 
the leg support screws (C) - left and right, and remove the leg 
support cover (D). Then place it on the opposite side. Unscrew, 
remove and then replace the position of the end switch (E) and 
decorative peg (F) (for...

 29
roubleshooting 
 
NT: If your fridge freezer appears not to be 
perating properly, before  contacting the Baumatic 
is no power to my appliance. 
e to the power socket. 
o  Check that there is power to yo
 
Check that the appliance isn’t ov
been packed too tightly into it.  or has 
The refrigerant gas that circulates the pipework of the appliance 
may make a slight noise, even if the compressor is not running. 
  on the inner back wall of my fridge 
o  pushed too far back inside 
k 
There is water...

 30
Bau
 
ic appliance comes complete with a free 12 month guarantee covering both parts and 
lting from defective materials or workmanship. 
onths. The extended guarantee period 
w.baumatic.co.uk
matic Ltd. Conditions of Guarantee 
Dear Customer, 
 
Your new Baumatabour costs resu
l
 
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12  onths at no extra cost, giving an initial guarantee period of 24 m
m
applies to England, Scotland, Wales and Northern...