Brother Mfc 7360 N Manual

							Loading paper
11
2
bWhile pressing the green paper-guide 
release lever, slide the paper guides to 
fit the paper size you are loading in the 
tray. Make sure that the guides are 
firmly in the slots.
 
cFan the stack of paper well to avoid 
paper jams and misfeeds.
 
dPut paper in the tray and make sure:
The paper is below the maximum 
paper mark (b b b) (1).
Overfilling the paper tray will cause 
paper jams.
The side to be printed on must be 
face down.
The paper guides touch the sides of 
the paper so it will feed properly.
 
ePut the paper tray firmly back in the 
machine. Make sure that it is completely 
inserted into the machine.
1 
						

							Chapter 2
12
fUnfold the support flap (1) to prevent 
paper from sliding off the face-down 
output tray.
 
Loading paper in the manual 
feed slot2
You can load envelopes and special print 
media one at a time into this slot. Use the 
manual feed slot to print or copy on labels, 
envelopes or thicker paper.
Note
The machine automatically turns on the 
Manual Feed mode when you put paper in 
the manual feed slot.
 
Printing on plain paper, thin paper or 
recycled paper from the manual feed 
slot
2
aUnfold the support flap (1) to prevent 
paper from sliding off the face-down 
output tray, or remove each page as 
soon as it comes out of the machine.
 
bOpen the manual feed slot cover. 
1
1
1
1 
						

							Loading paper
13
2
cUsing both hands, slide the manual feed 
slot paper guides to the width of the 
paper that you are going to use.
 
dUsing both hands, put one sheet of 
paper in the manual feed slot until the 
front edge of the paper touches the 
paper feed roller. When you feel the 
machine pull in the paper, let go.
 
Printing on thick paper, bond paper, 
labels and envelopes
2
When the back output tray is pulled down, the 
machine has a straight paper path from the 
manual feed slot through to the back of the 
machine. Use this paper feed and output 
method when you want to print on thick 
paper, labels or envelopes.
Note
Remove each printed sheet or envelope 
immediately to prevent a paper jam.
 
aOpen the back cover (back output tray).  
						

							Chapter 2
14
Note
 
Pull down the two green levers, one on the 
left-hand side and one on the right-hand 
side, as shown in the following illustration.
 
 
bOpen the manual feed slot cover. 
cUsing both hands, slide the manual feed 
slot paper guides to the width of the 
paper that you are going to use.
 
dUsing both hands, put one sheet of 
paper or one envelope in the manual 
feed slot until the front edge of the paper 
or envelope touches the paper feed 
roller. When you feel the machine pull in 
the paper, let go.
  
						

							Loading paper
15
2
 
Note
• Put the paper into the manual feed slot 
with the side to be printed face up.
• Make sure that the print media is straight 
and in the correct position on the manual 
feed slot. If it is not, the paper may not be 
fed properly, resulting in a skewed printout 
or a paper jam.
• Do not put more than one sheet of paper 
in the manual feed slot at any one time, as 
it may cause a jam.
• If you put any print media in the manual 
feed slot before the machine is in Ready 
mode, the print media may be ejected 
without being printed on.• To easily remove a small printout from the 
output tray, lift up the scanner cover by 
using both hands as shown in the 
illustration.
 
• You can still use the machine while the 
scanner cover is up. To close the scanner 
cover, push it down with both hands.
 
  
						

							Chapter 2
16
Unscannable and unprintable areas2
The figures below show maximum unscannable and unprintable areas. The unscannable and 
unprintable areas may vary depending on the paper size or settings in the application you are 
using.
 Usage Document 
SizeTop (1)
Bottom (1)Left (2)
Right (2)
Fax (Send) Letter 3 mm 4 mm
A4 3 mm 3 mm
Copy
*a single copy 
or a 1 in 1 copyLetter 3 mm 4 mm
A4 3 mm 3 mm
Scan Letter 3 mm 3 mm
A4 3 mm 3 mm
Print Letter 4 mm 6.35 mm
A4 4mm 6.35mm
2
2
1
1 
						

							Loading paper
17
2
Paper settings2
Paper Type2
Set up the machine for the type of paper you 
are using. This will give you the best print 
quality.
aPress Menu, 1, 2, 1.
bPress a or b to choose Thin, Plain, 
Thick, Thicker, Recycled Paper or 
Label.
Press OK.
cPress Stop/Exit.
Paper Size2
You can use several different sizes of paper 
for printing copies: A4, Letter, Legal, 
Executive, A5, A5 L, A6, B5, B6 and Folio and 
for printing faxes: A4, Letter, Legal or Folio 
(215.9 mm  330.2 mm).
When you change the size of paper in the 
tray, you will also need to change the setting 
for paper size at the same time so your 
machine can fit the document or an incoming 
fax on the page.
aPress Menu, 1, 2, 2.
bPress a or b to choose A4, Letter, 
Legal, Executive, A5, A5 L, A6, B5, 
B6 and Folio.
Press OK.
cPress Stop/Exit.
Acceptable paper and 
other print media
2
Print quality may vary according to the type of 
paper you are using.
You can use the following types of print 
media: thin paper, plain paper, thick paper, 
bond paper, recycled paper, labels or 
envelopes.
For best results, follow the instructions below:
DO NOT put different types of paper in the 
paper tray at the same time because it 
may cause paper jams or misfeeds.
For correct printing, you must choose the 
same paper size from your software 
application as the paper in the tray.
Avoid touching the printed surface of the 
paper immediately after printing.
Before you buy a lot of paper, test a small 
quantity to make sure the paper is 
suitable.
Recommended paper and 
print media2
Paper TypeItem
Plain paper
Xerox Premier TCF 80 g/m
2
Xerox Business 80 g/m2
Recycled Paper
Xerox Recycled Supreme 
80 g/m
2
Labels Avery laser label L7163
Envelope Antalis River series (DL) 
						

							Chapter 2
18
Type and size of paper2
The machine loads paper from the installed 
standard paper tray or manual feed slot.
The name for the paper trays in the 
printer driver in this Guide are as 
follows:
2
Paper capacity of the paper trays2
1Folio size is 215.9 mm  330.2 mm.
2Legal or Folio size paper are not available in some regions.
Recommended paper specifications2
The following paper specifications are suitable for this machine.
Use paper made for plain paper copying.
Use paper that is 75 to 90 g/m
2.
Use long grain paper with a neutral Ph value, and a moisture content of approx. 5%.
This machine can use recycled paper that meets DIN 19309 specifications.
Tray and optional unitName
Standard paper tray Tray 1
Manual feed slot Manual
Paper sizePaper typesNo. of sheets
Paper Tray 
(Tray 1)A4, Letter, Legal
2, 
Executive, A5, 
A5 (Long Edge), A6, B5, 
B6 and Folio
12.Plain paper, Thin paper 
and Recycled paperup to 250 [80 g/m
2]
Manual feed slot 
(Manual)Width: 76.2 to 216 mm
Length: 116 to 406.4 mmPlain paper, Thin paper, 
Thick paper, 
Bond paper, 
Recycled paper, 
Envelopes and LabelsSingle sheet
[80 g/m
2]
Basis weight
75-90 g/m
2
Thickness 80-110 m
Roughness Higher than 20 sec.
Stiffness
90-150 cm
3/100
Grain direction Long grain
Volume resistivity
10e
9-10e11 ohm
Surface resistivity
10e
9-10e12 ohm-cm
FillerCaCO
3 (Neutral)
Ash content Below 23 wt%
Brightness Higher than 80%
Opacity Higher than 85% 
						

							Loading paper
19
2 Handling and using special 
paper2
The machine is designed to work well with 
most types of xerographic and bond paper. 
However, some paper variables may have an 
effect on print quality or handling reliability. 
Always test samples of paper before 
purchasing to ensure desirable performance. 
Store paper in its original packaging and keep 
it sealed. Keep the paper flat and away from 
moisture, direct sunlight and heat.
Some important guidelines when selecting 
paper are:
DO NOT use inkjet paper because it may 
cause a paper jam or damage your 
machine.
Preprinted paper must use ink that can 
withstand the temperature of the 
machine’s fusing process 392 degrees 
Fahrenheit (200 degrees centigrade).
If you use bond paper, paper having a 
rough surface or paper that is wrinkled or 
creased, the paper may exhibit degraded 
performance.
Types of paper to avoid2
IMPORTANT
Some types of paper may not perform well 
or may cause damage to your machine.
DO NOT use paper:
• that is highly textured
• that is extremely smooth or shiny
• that is curled or warped
 
1 A curl of 2 mm or greater may cause 
jams to occur.
• that is coated or has a chemical finish
• that is damaged, creased or folded
• that exceeds the recommended weight 
specification in this guide
• with tabs and staples
• with letterheads using low temperature 
dyes or thermography
• that is multipart or carbonless
• that is designed for inkjet printing
If you use any of the types of paper listed 
, they may damage your machine. This 
damage is not covered under any Brother 
warranty or service agreement.
 
11 
						

							Chapter 2
20
Envelopes2
Most envelopes designed for laser printers 
will be suitable for your machine. However, 
some envelopes may have feed and print-
quality problems because of the way they 
have been made. A suitable envelope should 
have edges with straight, well-creased folds 
and the leading edge should not be thicker 
than two sheets of paper. The envelope 
should lie flat and not be of baggy or flimsy 
construction. You should buy quality 
envelopes from a supplier who understands 
that you will be using the envelopes in a laser 
machine.
Envelopes can be fed from the manual feed 
slot one at a time. We recommend that you 
print a test envelope to make sure the print 
results are what you want before you print or 
purchase a large quantity of envelopes.
Types of envelopes to avoid2
IMPORTANT
DO NOT use envelopes:
• that are damaged, curled, wrinkled or 
an unusual shape
• that are extremely shiny or textured
• with clasps, staples, snaps or tie 
strings
• with self-adhesive closures
• that are of a baggy construction
• that are not sharply creased
• that are embossed (have raised writing 
on them)
• that were previously printed by a laser 
machine
• that are pre-printed on the inside
• that cannot be arranged neatly when 
stacked
• that are made of paper that weighs 
more than the paper weight 
specifications for the machine
• with edges that are not straight or 
consistently square• with windows, holes, cut-outs or 
perforations
• with glue on surface as shown in figure 
below
 
•with double flaps as shown in figure below
 
• with sealing flaps that are not folded 
down when purchased
•
with sealing flaps as shown in figure below
 
• with each side folded as shown in 
figure below
 
If you use any of the types of envelopes 
listed above, they may damage your 
machine. This damage may not be 
covered under any Brother warranty or 
service agreement.