Canon Imageclass Mf7470 User Guide

							
Copying
3‑4

Paper Selection
You can manually specify a paper size or set the machine to automatically select the 
paper size for you.
If you are copying an original with an image that extends all the way to\
 the edges onto the same size paper 
at a copy ratio of 100%, the periphery of the original image may be cut off slightly on the copy. For more 
information on how much may be cut off, see “Scanning Area,” on p. 2‑4.
If you select [Envelope], [Transparency], or [Labels], make sure that yo\
u do not specify any Finishing modes 
(Collate or Group).
If Stack Bypass Standard Settings in Common Settings (from the Addition\
al Functions screen) is set to [On], 
and the paper size/type have been stored, the selected paper size/type are displayed on the screen. (See 
“Stack Bypass Standard Settings,” on p. 12‑8.)
Automatic Paper Selection
The machine automatically selects the copy paper size.
The Automatic Paper Selection mode is available only if the originals ar\
e fed from the feeder.
The Automatic Paper Selection mode cannot be used with the Auto Zoom or \
Image Combination mode.
You cannot use the Automatic Paper Selection mode when copying the follo\
wing types of originals. Copy 
these originals using the Manual Paper Selection mode.
Nonstandard size originals
Highly transparent originals, such as transparencies
Originals with an extremely dark background
STMT or STMTR originals that are placed on the platen glass
If Drawer Eligibility For APS/ADS in Common Settings (from the Additional Functions screen) is set to [Off] 
for a particular paper source, you cannot make copies on paper loaded in that paper source in the Automatic 
Paper Selection mode. (See “Drawer Eligibility For APS/ADS ,” p. 12‑7.)
–
–
–
–
–
–
–
–
–
–
–
 
						

							
3‑5
Copying

1 Press  (COPY).
2 Place your originals.
3 
4 
① Press [Auto].
②  Press [Done].
When the feeder is closed, the paper source 
holding that paper size is highlighted along 
with [Auto].
5  Press  (Start).
ƒ„ƒ„
 
						

							
Copying
3‑6

Manual Paper Selection
You can make copies after manually selecting the paper size and type of paper loaded in 
the paper sources.
You can copy an image onto envelopes, such as your company logo. Envelopes can be loaded into the stack 
bypass.
1 Press  (COPY).
2 Place your originals.
If you want to set the size/type for the paper 
to be fed from the stack bypass, proceed to 
step 5.
If you want to set the size/type for the paper 
loaded in a paper drawer, proceed to step 3.
3 
When the feeder is closed, the paper source 
holding that paper size is highlighted along 
with [Auto].
4 
① Select the desired paper size.
②  Proceed to step 7.
The paper sizes/types loaded in each paper 
drawer are indicated by icons on the touch 
panel display.
Icons indicating the type of paper loaded 
in each paper drawer can be displayed 
on paper select screens, if you store that 
information in the machine beforehand. 
(See chapter 3, “Copying,” in the Reference 
Guide.)
 indicates that the paper is loaded 
vertically, and  indicates that the paper is 
loaded horizontally. The suffix  (such as 
in LTRR), used in paper size designations, 
indicates that the paper is loaded in 
a paper drawer or the stack bypass 
horizontally.
–
–
–
ƒƒ
 
						

							
3‑7
Copying

5 For the stack bypass setting, load 
the paper into the stack bypass.
The paper size/type setting in the [Stack 
Bypass] setting screen is available if Stack 
Bypass Standard Settings is set to [Off] in 
Common Settings (from the Additional 
Functions screen). If Stack Bypass Standard 
Settings is set to [On], copying can be 
performed only for the registered paper 
size and type. (See “Stack Bypass Standard 
Settings,” on p. 12‑8.)
If you want to select a standard 
paper size:
1
①  Select the desired paper size.
②  Press [Next].
To select an A or B series paper size, press 
[A/B‑size].
Ô
ƒ
„
ƒ
„
2
①  Select the desired paper type.
②  Press [OK].
When printing on special types of paper, 
such as heavy paper or transparencies, 
be sure to correctly set the paper type, 
especially if you are using heavy paper. 
If the type of paper is not set correctly, 
it could adversely affect the quality of 
the image. Moreover, the fixing unit 
may become dirty and require a service 
repair, or the paper could jam.
If you select [Transparency] or [Labels], 
make sure that you do not specify any 
Finishing modes (Collate or Group).
[Transparency] can be selected only if 
[LTR] is selected as the paper size.
[3‑hole punch] can be selected only if 
[LTR] or [LTRR] is selected as the paper 
size.
If you want to select a 
nonstandard paper size:
1
–
–
–
–
Ô
ƒ
„
ƒ
„
 
						

							
Copying
3‑8

2
① Press [X] to specify the horizontal axis 
of the paper, then enter a value.
②  Press [Y] to specify the vertical axis of 
the paper, then enter a value.
③  Press [OK].
If you make a mistake when entering 
values, press [C] on the touch panel 
display, then enter the correct values.
To enter values in millimeters, press 
[mm].
If you enter values outside the setting 
range, [OK] is grayed out and cannot be 
selected. Enter an appropriate value.
You can adjust values for [X] between 5 
7/8" and 17", and for [Y] between 3 3/4" 
and 11 11/16".
3
–
–
–
–
4
①  Select the desired paper type.
②  Press [OK].
When printing on special types of paper, 
such as heavy paper, be sure to correctly 
set the paper type, especially if you are 
using heavy paper. If the type of paper 
is not set correctly, it could adversely 
affect the quality of the image. 
Moreover, the fixing unit may become 
dirty and require a service repair, or the 
paper could jam.
If you select [Irreg. Size] for copying, you 
cannot use the Rotate Collate, Rotate 
Group, 1 ▶  2‑Sided, 2 ▶ 2‑Sided, Book 
▶ 2‑Sided, 2‑Page Separation, Image 
Combination mode.
If you want to select an envelope 
size:
1
–
–
Ô
ƒ
„
ƒ
„
 
						

							
3‑9
Copying

2
① Select the desired envelope type.
②  Press [OK].
If the envelope type is not selected 
correctly, a paper jam will occur.
If an envelope size is selected, the 
Finishing, 1 ▶  2‑Sided, 2 ▶ 2‑Sided, 
Book ▶ 2‑Sided, 2‑Page Separation, or 
Image Combination mode cannot be 
specified.
3
6 
7  Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
–
–
ƒ
„
ƒ
„
 
						

							
Copying
3‑10

Scan Settings
You can set the desired copy exposure and select the original type before scanning 
the original.
Manual Exposure Adjustment
You can manually adjust the copy exposure to the most appropriate level for the original.
Original Type Selection
The machine is capable of processing and producing copies according to the type of 
the original. You can manually select the original type so that the machine reproduces 
copies as faithful as possible to the original. The following three original type modes are 
available:
Text ModeText/Photo ModePhoto Mode
Text Mode
This mode is best suited for making copies of text originals. Blueprints or pencil drawn 
originals can also be copied clearly.
Text/Photo Mode
This mode is best suited for making copies of originals containing both text and 
images/photos, such as magazines or catalogues.
Photo Mode
This mode is best suited for making copies from photos printed on photographic 
paper, or making copies of images printed with halftone dots (i.e., printed photos).
Automatic Exposure Adjustment
This mode enables you to set the machine to automatically adjust the exposure to the 
level best suited to the quality of the original.
Exposure Adjustment during Printing
You can change the copy exposure while the machine is printing.
Ô
Ô
–
–
–
Ô
Ô
 
						

							
3‑11
Copying

Original Type Selection
Combinations of these three modes (Text, Text/Photo, and Photo) cannot\
 be selected at the same time. If you 
select one of these modes, the previously set mode is canceled.
If you make copies of an original containing halftones, such as a printed photograph, using the Photo mode, 
the moiré effect (a shimmering, wavy pattern) may occur. In this ca\
se, you can lessen the moiré effect by 
using the Sharpness mode. (See chapter 3, “Copying,” in the Refer\
ence Guide.)
If you select the Automatic Exposure Adjustment mode, the original type \
mode is grayed out and fixed to 
Text mode. If you select the Text/Photo or Photo mode, the exposure can only be adjusted manually.
If the original is a transparency, select the original type, then adjust\
 the exposure to the most appropriate 
level for the original.
–
–
–
–
1 Press  (COPY).
2 Place your originals.
3 
① Press .
4 
①  Select the original type.
ƒƒ
5  Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
 
						

							
Copying
3‑12

Exposure
You can adjust the density to the most appropriate level for the original either automatically 
or manually.
Adjusting AutomaticallyÔ
1 Press  (COPY).
2 Place your originals.
3 
The machine automatically adjusts the copy 
exposure to the level best suited to the 
quality of the original.
An automatic copy exposure adjustment 
may not work with transparencies. In this 
case, adjust the copy exposure manually by 
pressing [Light] or [Dark]. 
4 Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
 
						

							
3‑13
Copying

Adjusting ManuallyÔ
1 Press  (COPY).
2 Place your originals.
3 
① Press [Light] or [Dark].
Press [Light] to move the indicator to the 
left to make the exposure lighter, or press 
[Dark] to move it to the right to make the 
exposure darker.
4  Press  (Start).
To cancel all settings and return the machine 
to the Standard mode, press  (Reset).
ƒƒ