Canon printer PIXMA MX490 User Manual

Front View
(1) ADF (Auto Document Feeder)Load a document here. The documents loaded in the document tray are scanned automatically one
sheet at a time.
Loading Documents in the ADF (Auto Document Feeder)
(2) operation panel Use to change the settings of the machine or to operate it.
Operation Panel
(3) document feeder cover Open when clearing jammed documents.
(4) document guide Adjust this guide to match the width of document in the ADF.
(5) document tray Open to load a document in the ADF. You can load...

(11) paper output trayPrinted paper is ejected.
(12) paper output support Pull out to support ejected paper.
(13) output tray extension Open to support ejected paper.
(14) paper output cover Open to replace the FINE cartridge or remove jammed paper inside the machine.
(15) POWER lampLights after flashing when the power is turned on.
(16) FAX Memory lamp Lights when there are received or unsent documents stored in the machine's memory.
(17) Alarm lamp Lights or flashes when an error occurs.
(18) ON...

Rear View
(1) power cord connectorPlug in the supplied power cord.
(2) transport unit Open when removing jammed paper.
(3) telephone line jack Connect the telephone line.
(4) external device jack Connect an external device such as telephone or answering machine.
(5) USB port Plug in the USB cable to connect the machine with a computer.
Important
•
Do not touch the metal casing.
•
Do not plug in or unplug the USB cable while the machine is printing or scanning originals with thecomputer.
113 

Inside View
(1) FINE cartridge (ink cartridges)A replaceable cartridge that integrates print head and ink tank.
(2) FINE cartridge holder Install the FINE cartridges here.
The color FINE cartridge should be installed into the left slot and the black FINE cartridge should be
installed into the right slot.
Note
•
For details on replacing a FINE cartridge, see Replacing a FINE Cartridge .
Important
•
The area around the parts (A) may be splattered with ink. This does not affect the performance of the...

Operation Panel
(1) LCD (Liquid Crystal Display)Displays messages, menu items, and the operational status.
(2) Back button Returns the LCD to the previous screen.
(3) FAX button Switches the machine to the fax mode.
(4) COPY button Switches the machine to the copy mode.
(5) SCAN button Switches the machine to the scan mode.
(6) Setup button Displays the  Setup menu screen. With this menu, you can perform machine maintenance and change
machine settings.
(7) Black button Starts black & white copying,...

(12) Numeric buttonsUsed to enter numerical values such as the number of copies, as well as fax/telephone numbers and
characters.
(13) Tone button Switches to tone dialing temporarily if your machine is connected to a rotary pulse line.
(14) Stop button Cancels operation when print, copy, scan, or fax transmission/reception job is in progress.
Note
•
The machine makes the beep sound when pressing keypad buttons on the operation panel. Thekeypad sound can be enabled or disabled in  Sound control of Dev....

About the Power Supply of the Machine
Confirming that the Power Is On
Turning the Machine On and Off
Notice for the Power Plug/Power Cord
Notice for Unplugging the Power Cord
117 

Confirming that the Power Is OnThe  POWER  lamp is lit when the machine is turned on.
Even if the LCD is off, if the  POWER lamp is lit, the machine is on.
Note
•
It may take a while for the machine to start printing immediately after you turn on the machine.
•
The LCD will turn off if the machine is not operated for about 5 minutes. To restore the display, press
any button except the  ON button or perform the print operation. The display will be also restored when
receiving faxes. You cannot change the...

Turning the Machine On and OffTurning on the machine1.
Press the  ON button to turn on the machine.
The  POWER  lamp flashes and then remains lit.
Confirming that the Power Is On
Note
•
It may take a while for the machine to start printing immediately after you turn on the machine.
•
If the Alarm  lamp lights up or flashes and an error message is displayed on the LCD, see A
Message Is Displayed .
Turning off the machine
1.
Press the  ON button to turn off the machine.
When the  POWER lamp stops flashing,...

Notice for the Power Plug/Power CordCheck the power plug/power cord once a month to confirm that it does not have anything unusual describedbelow.•
The power plug/power cord is hot.
•
The power plug/power cord is rusty.
•
The power plug/power cord is bent.
•
The power plug/power cord is worn.
•
The power plug/power cord is split.
Caution
•
If you find anything unusual with the power plug/power cord described above, unplug the power cord
and call for service. Using the machine with one of the unusual...