Carrier Comfort Zone 1 Manual

							 
11 
PROGRAMMING
 
To  
ONLY VIEW 
 the start times and setpoints for
each start time, press the SELECT MIN/HR/DAY
button a second time. This will display the second
start time and setpoints.
Additional presses will display start times 3 and 4, then
return to weekly period display. 
A95575
A95578A95579 
NOTE: 
While in the program mode, if a period of 4-1/2 minutes passes
without a change to some value, the controller will revert to normal operation.
SET
TIME/TEMP
SCHEDULES
HOLD
TEMPERATURESSELECT
MIN/HR/DAY
ADVANCE
TIME/DAY
HEAT
PROGRAM
COOLAM 
						

							 
12 
PROGRAMMING
 
5. Program Start Time
 
PLEASE NOTE: START TIMES MUST
 BE PROGRAMMED IN CHRONOLOGICAL ORDER
AND ALL START TIMES MUST BE IN THE SAME DAY.
NOTE: 
 It is not recommended to use 12.00 a.m. for programming schedule. This may result in a time period 
programming error.
Press the ADVANCE TIME/DAY button until the desired start time is displayed.
 
A95574 A95579 
RIGHT
 
6 AM - Time Period 1
8 AM  - Time Period 2
5 PM - Time Period 3
9 PM - Time Period 4
WRONG
6 AM - Time Period 1
2 AM - Time Period 2
9 PM - Time Period 3
5 PM - Time Period 4
WRONG
8 AM - Time Period 1
5 PM - Time Period 2
2 AM - Time Period 3
6 AM - Time Period 4
SET
TIME/TEMP
SCHEDULES
HOLD
TEMPERATURESSELECT
MIN/HR/DAY
ADVANCE
TIME/DAY
AM 
						

							13
PROGRAMMING
6. Adjust Setpoints
Adjust the setpoints using the setpoint UP and DOWN buttons until the desired temperatures for the selected time
period appear in the display. These setpoints will be used during the time period currently displayed in the clock
window.
Press to adjust Press to adjust
Cooling Setpoint Heating Setpoint
A95580
7. Complete Time Period Programming
Repeat steps 4 through 6 to program remaining weekly period start times. Each weekly period can be programmed
with 4 different time periods.
8. Complete Week Schedule
After completing start time programming, press the SELECT MIN/HR/DAY button until “MTWTHF” reappears in the
clock display.
Repeat steps 3 through 7 to program remaining weekly periods. Once finished, this will complete the programming
of 1 zone.
9. Program a Different Zone
To program a different zone, turn the selection dial to the desired ZONE to be programmed and repeat steps 2
through 8.
10. Exit Program Mode
Exit the program mode by pressing the SET TIME/TEMP SCHEDULES button.
HEATCOOL
PROGRAM 
						

							14
OVERRIDING PROGRAMMING
To override the time programming, press any setpoint button. This will also adjust the setpoints for the override period.
Once the setpoints are adjusted, they will not change until the next programmed time period.
Press to adjust Press to adjust
Cooling Setpoint Heating Setpoint
A95581
If the HOLD TEMPERATURES button is pressed, the current
setpoints will not change with time, but remain at the
last values entered for as long as the hold mode is active.
To release the hold mode, press the HOLD TEMPERATURES
button a second time.
A95582
The controller display will show the word HOLD
whenever the hold mode is active.
A95583
SET
TIME/TEMP
SCHEDULESSELECT
MIN/HR/DAY
ADVANCE
TIME/DAYHOLD
TEMPERATURES
HEATCOOL
HOLD
HEATCOOL 
						

							15
PROGRAMMING QUICK REFERENCE
Program
1. Press SET TIME/TEMP SCHEDULES   to enter program mode.
2. Select desired zone, using zone select dial.
3.  Press ADVANCE TIME/DAY   to select weekly period to program.
4. Press SELECT MIN/HR/DAY  to program selected daily period.
5. Press ADVANCE TIME/DAY   to change time for selected period.
6. Adjust temperature setpoints for selected period.
 7. Repeat steps 4–6 to program remaining periods in daily schedule.
8. Repeat steps 3–7 to program remaining weekly periods.
9. Repeat steps 2–8 to program remaining zones.
10. Press SET TIME/TEMP SCHEDULES   at any time to exit program mode.
Time Set
1. Press SELECT MIN/HR/DAY   to enter time set mode.
2. Press ADVANCE TIME/DAY   to change minutes.
3. Repeat steps 1–2 to set hrs/days or exit.
Hold
Press HOLD TEMPERATURES   to retain current temperature setpoints. 
						

							TO OBTAIN INFORMATION ON PARTS: Consult your installing dealer or classified section of your local telephone directory under the
“Heating Equipment’’ or “Air Conditioning Contractors & Systems’’ headings for dealer listing by brand name. 
Have available the Model No., Series Letter & Serial No. of your equipment to insure correct replacement part.
Carrier Corporation   Syracuse, New York 13221
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Copyright 1996 Carrier Corporation Form: OMZONEKIT4-1 Supercedes: New Printed in the U.S.A. 3-96 PC 101 Catalog No. 809-575
®
PROGRAMMING CHART
A95584
ZONE 1 MTWTHF SA SU
AREA
COMMENTS:
START TIME
TIME PERIOD 4Cool
HeatCool
HeatCool
HeatSTART TIME START TIME
TIME PERIOD 3 TIME PERIOD 2 TIME PERIOD 1
ZONE 2 MTWTHF SA SU
AREA
COMMENTS:
START TIME
TIME PERIOD 4Cool
HeatCool
HeatCool
HeatSTART TIME START TIME
TIME PERIOD 3 TIME PERIOD 2 TIME PERIOD 1
ZONE 3 MTWTHF SA SU
AREA
COMMENTS:
START TIME
TIME PERIOD 4Cool
HeatCool
HeatCool
HeatSTART TIME START TIME
TIME PERIOD 3 TIME PERIOD 2 TIME PERIOD 1
ZONE 4 MTWTHF SA SU
AREA
COMMENTS:
START TIME
TIME PERIOD 4Cool
HeatCool
HeatCool
HeatSTART TIME START TIME
TIME PERIOD 3 TIME PERIOD 2 TIME PERIOD 1