compaq notebook 100 series User Manual

							A-2Connector Pin Assignments
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-3
Microphone Jack
Connector Pin Signal
1
2
1
2Audio in
Ground
Table A-4
Stereo Speaker/Headphone Jack
Connector Pin Signal
1
2
1
2Audio out
Ground
Table A-5
Stereo Line-in Jack
Connector Pin Signal
1
2
1
2Audio in
Ground 
						

							Connector Pin AssignmentsA-3
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-6
Parallel  Connector
1 2 3 4
15 16 17 14 5 6 7 8 9 10 11 12 13
18 20 19 21 22 23 25 24
Pin Signal Pin Signal
  1 Strobe 14 Auto Linefeed
  2 Data Bit 0 15 Error
  3 Data Bit 1 16 Initialize Printer
  4 Data Bit 2 17 Select In
  5 Data Bit 3 18 Ground
  6 Data Bit 4 19 Ground
  7 Data Bit 5 20 Ground
  8 Data Bit 6 21 Ground
  9 Data Bit 7 22 Ground
10 Acknowledge 23 Ground
11 Busy 24 Ground
12 Paper End 25 Ground
13 Select 
						

							A-4Connector Pin Assignments
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-7
Docking Connector
31
61
911
120 90 60 30
Pin Signal Pin Signal
  1 EBOXL 29 XA3/R IN
  2 AGND 30 MID0/MIC IN
  3 EBOXS1 31 AUGND
  4 RED 32 XA0/L OUT
  5 AGND 33 XSD/MIC SN
  6 GREEN 34 XA1/R OUT
  7 AGRD 35 GND
  8 BLUE 36 GND
  9 AGND 37 EXPCLK2
10 VSYNC 38 +3.3V
11 HSYNC 39 EXPCLK0
12 DDC DAT 40 +5V (8051VCC)
13 DDC CLK 41 EXPCLK
14 GND 42 EBOXS2
15 INDEX 43 GND
16 RDATA 44 EBOXL
17 TRK0 45 EBOXL /GND
18 WDATA 46 SRDY
19 WGATE 47 EBOXS1 /GND
20 STEP 48 RI1 EX
21 DIR 49 GND
22 POWER ON 50 SLCT LD0
23 SYS RESET 51 PE LD1
24 GND 52 ACK LD2
25 DSKCHG 53 BUSY LD3
26 +5 V (VDD) 54 GND
27 AUGND 55 STRB LD4
28 XA2/L IN 56 ALF LD5
Continued  
						

							Connector Pin AssignmentsA-5
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-7  continued
Pin Signal Pin Signal
57 INIT LD6   91 PS2 VCC
58 SLCTIN LD7   92 SERIRQ
59 GND   93 PS2 CLK
60 PDATA0 LD8   94 EXPREQ
61 PDATA1 LD9   95 AD[29]
62 PDATA2 LD10   96 AD[31]
63 PDATA3 LD11   97 AD[30]
64 GND   98 AD[28]
65 PDATA4 LD12   99 AD[26]
66 PDATA5 LD13 100 GND
67 PDATA6 LD14 101 AD[24]
68 PDATA7 LD15 102 AD[22]
69 GND 103 AD[20]
70 ERROR LCLK 104 AD[18]
71 RXD1 LVREQ 105 AD[16]
72 TXD1 LCREQ 106 GND
73 RTS1 LEN 107 AD[15]
74 GND 108 AD[13]
75 CTS1 LIIC CLK 109 AD[11]
76 DTR1 LIIC DAT 110 AD[09]
77 DSR1 EX 111 GND
78 DCD1 EX 112 AD[06]
79 12C DATA 113 AD[04]
80 GND 114 AD[02]
81 12C CLK 115 AD[00]
82 GND 116 GND
83 HDSEL 117 FRAME
84 GND 118 TRDY
85 WPROT 119 STOP
86 EBOXS2 /GND 120 PAR
87 ERDY 121 CBE0
88 EBOXL /GND 122 CBE1
89 FLUSHREQ 123 GND
90 MEMACK 124 KB CLK
Continued  
						

							A-6Connector Pin Assignments
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-7  continued
Pin Signal Pin Signal
125 RSVD1/M CTRL2 151 AD[12]
126 XSC/L OUT SN 152 AD[10]
127 RSVD2/M OFF HOOK 153 AD[08]
128 KB DATA 154 GND
129 MGND 155 AD[07]
130 STANDBY 156 AD[05]
131 M DRZP 157 AD[03]
132 M DRXN 158 AD[01]
133 VBATT 159 GND
134 EXPGNT 160 CBE3
135 VBATT 161 CBE2
136 GND 162 IRDY
137 VBATT 163 DEVSEL
138 PS2 DATA 164 LOCK
139 VBATT 165 OERR
140 AD[25] 166 SERR
141 VBATT 167 GND
142 AD[27] 168 RSVD3
143 VBATT 169 M 12C CLK
144 AD[23] 170 M 12C DATA
145 GND 171 M RING
146 AD[21] 172 MGND
147 AD[19] 173 M DXTN
148 AD[17] 174 GND
149 GND 175 M DXTP
150 AD[14] 176 MSTRBAT 
						

							Connector Pin AssignmentsA-7
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appa.doc
Table A-8
External Keyboard/Mouse Connector
Connector Pin Signal
KEY 65
43
21
1
2
3
4
5
6Keyboard/Mouse DATA
Keyboard/Mouse DATA
Ground
+5 VDC
Keyboard/Mouse CLK
Keyboard/Mouse CLK
Table A-9
External Monitor Connector
1
6 2 3
87 4 5
10
KEY
11 12 13 14 15
Pin Signal Pin Signal
1 Red Analog   9 NC
2 Green Analog 10 Ground
3 Blue Analog 11 NC
4 NC 12 DDC Data
5 Ground 13 Horizontal Sync
6 Ground 14 Vertical Sync
7 Ground 15 DDC Clock
8 Ground 
						

							Power Cord Set RequirementsB-1
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Pages: 2    Words: 419    Template: c:\msoffice	emplates
ef
ef.dot
Part Number: 177845-001     File name: Appb.doc
appendix
 
B
POWER CORD SET REQUIREMENTS
3-Conductor Power Cord Set
The wide range input feature of the Compaq Notebook 100 Personal
Computer permits it to operate from any line voltage from 100 to 120 or
220 to 240 volts AC.
The power cord sets received with the computers meets the requirements
for use in the country where the equipment is purchased.
Power cord sets for use in other countries must meet the requirements of
the country where the computer is used. For more information on power
cord set requirements, contact a Compaq authorized reseller or service
provider.
General Requirements
The requirements listed below are applicable to all countries:
1.  The length of the power cord set must be at least 5.00 feet (1.5 m)
and a maximum of 6.50 feet (2.0 m).
2.  All power cord sets must be approved by an acceptable accredited
agency responsible for evaluation in the country where the power
cord set will be used.
3.  The power cord set must have a minimum current capacity of 10A
and a nominal voltage rating of 125 or 250 volts AC, as required by
each country’s power system.
4.  The appliance coupler must meet the mechanical configuration of an
EN 60 320/IEC 320 Standard Sheet C13 connector, for mating with
appliance inlet on the back of the computer. 
						

							B-2Power Cord Set Requirements
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: David Calvert    Saved by: JAbercrombie    Saved date: 04/05/00 12:53 PM
Part Number: 177845-001     File name: Appb.doc
Country-Specific Requirements
3-Conductor Power Cord Set Requirements—By Country
Country Accredited AgencyApplicable Note
Numbers
Australia EANSW 1
Austria OVE 1
Belgium CEBC 1
Canada CSA 2
Denmark DEMKO 1
Finland FIMKO 1
France UTE 1
Germany VDE 1
Italy IMQ 1
Japan JIS 3
The Netherlands KEMA 1
Norway NEMKO 1
Sweden SEMKO 1
Switzerland SEV 1
United Kingdom BSI 1
United States UL 2
Notes
1.  The flexible cord must be  Type HO5VV-F, 3-conductor,
1.0 mm2
 conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency
responsible for evaluation in the country where it will be used.
2.  The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG,
3-conductor. The wall plug must be a two-pole grounding type with
a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V)
configuration.
3.  The appliance coupler, flexible cord, and wall plug must bear a T
mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCT or VCTF,
3-conductor, 0.75mm2
 conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303
(15A, 125V) configuration. 
						

							Index    I-1
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: JGilbert    Saved by: David Calvert    Saved date: 03/23/00 9:02 AM
Pages: 4    Words: 864    Template: c:\msoffice	emplates
ef
ef-indx.dot
Part Number: 177845-001     File name: Index.doc
INDEX
A
AC Adapter
spare part number, 3-8
specifications, 6-6
advance CPU controls menu, 1-14
applications. See software
B
base enclosure
illustrated, 3-2
spare part number, 3-3
battery pack, 5-4
illustrated, 3-2
Li ion
spare part number, 3-3, 5-4
specifications, 6-7
NiMH
spare part number, 3-3, 5-4
specifications, 6-7
removing, 5-4
C
Cable Kit
components
illustrated, 3-2, 3-6
spare part number, 3-3, 3-6
cables, 4-2
CD-ROM drive, 5-10
cable
disconnecting
from CD-ROM drive, 5-11
from system board, 5-10
illustrated, 3-2, 3-6
illustrated, 3-2, 3-7
removing, 5-10
spare part number, 3-3, 3-7, 5-10
specifications, 6-6
components menu, 1-11
computer
features, 1-3
major components
illustrated, 3-2
models, 1-2specifications, 6-1
configuration record utility, 1-16
connector
pin assignments, A-1
connectors, 4-2
D
design overview, 1-24
diagnostics, 1-19
disassembly
preparing the computer, 5-3
reference chart, 5-2
diskette drive, 5-38
cable
disconnecting
from diskette drive, 5-40
from system board, 5-36
illustrated, 3-6
illustrated, 3-2, 3-7
installing, 5-41
removing, 5-39
spare part number, 3-3, 3-7, 5-38
specifications, 6-5
disks menu, 1-9
display assembly, 5-27
cables
disconnecting, 5-28
DIP switches
setting, 5-31
components, 1-20
illustrated, 3-2
removing, 5-29
video cable
routing, 5-30
12.1-inch
spare part number, 3-3, 5-27
12.1-inch, STN
specifications, 6-3
12.1-inch, TFT
specifications, 6-3
docking
connector
pinout, A-4
DOS. See MS-DOS
drivers. See device drivers 
						

							I-2    Index
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
Writer: JGilbert    Saved by: David Calvert    Saved date: 03/23/00 9:02 AM
Part Number: 177845-001     File name: Index.doc
E
electrostatic
preventing damage, 4-3
voltage levels, 4-6
EMI shield
illustrated, 3-2
removing, 5-23
spare part number, 3-3, 5-23
ESD. See electrostatic discharge
exit menu, 1-15
external monitor
connector
illustrated, 1-23
F
fan assembly, 5-8
illustrated, 3-2
removing, 5-9
spare part number, 3-3, 5-8
fan/CPU cover
illustrated, 3-2, 3-4
removing, 5-8
features, 1-3
floppy disk drive. See diskette drive
G
gathering information, 1-17
grounding
equipment, 4-5
methods, 4-5
H
hard drive
illustrated, 3-2, 3-7
removing, 5-19
spare part number, 3-3, 3-7, 5-19
specifications, 6-4
Hardware Kit
components
illustrated, 3-2, 3-5
spare part number, 3-3, 3-5
headphone
jack
pinout, A-2
Hibernation, 1-6hinge covers
illustrated, 3-2, 3-4
removing, 5-27
I
I/O address. See input/output address
I/O cover
illustrated, 3-2, 3-4
removing, 5-32
IRQ. See interrupt requests
K
keyboard
cable
disconnecting, 5-22
connector
illustrated, 1-23
pinout, A-7
illustrated, 3-2
removing, 5-21
spare part number, 3-3, 5-21
L
left side components, 1-21
M
mass storage devices
illustrated, 3-7
spare part numbers, 3-7
memory, 5-15
expansion board
installing, 5-16
removing, 5-15
128 MB
spare part number, 5-1532 MBspare part number, 3-8, 5-1564 MBspare part number, 5-15menu, 1-9
options, 1-4
upgrade table, 1-4
microphone
jack
pinout, A-2