compaq notebook 100 series User Manual
Have a look at the manual compaq notebook 100 series User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Removal and Replacement Procedures5-33 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 6. Remove the five screws securing the speaker housing to the base assembly (Figure 5-30). 7. Remove the speaker housing . Figure 5-30. Removing the Speaker Housing Reverse the removal procedure described above to replace the speaker housing.
5-34Removal and Replacement Procedures COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 5.19 System Board System Board Spare Part Number Information System board with 32 MB SDRAM 176034-001 System board with 64 MB SDRAM 176035-001 RJ11 cover (spared with Plastics Kit) 176048-001 PC Card door (spared with Plastics Kit) 176048-001 1. Prepare the computer for disassembly (Section 5.3) and, in the order below, remove the following components: top cover (Section 5.10) hard drive (Section 5.11) RTC battery (Section 5.12) keyboard (Section 5.13) EMI shield (Section 5.14) TouchPad (Section 5.15) speakers (Section 5.16) display assembly (Section 5.17) speaker housing (Section 5.18) 2. Turn the computer bottom side up with the rear panel facing forward.
Removal and Replacement Procedures5-35 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 3. Remove the two screws securing the system board to the base assembly (Figure 5-31). Figure 5-31. Removing the System Board Screws 4. Turn the computer top side up with the front facing forward.
5-36Removal and Replacement Procedures COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 5. If installed, remove the RJ11 cover from the left side of the computer (Figure 5-32). 6. Disconnect the diskette drive LIF (low insertion force) cable from the system board . 7. Remove the system board from of the base assembly . Figure 5-32. Removing the System Board IMPORTANT: When installing the system board, make sure the diskette drive cable does not get trapped underneath the system board.
Removal and Replacement Procedures5-37 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc If necessary, remove the PC Card door by partially opening the door , flexing the middle of the door away from the computer , and removing the door (Figure 5-33). Figure 5-33. Removing the PC Card Door
5-38Removal and Replacement Procedures COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 5.20 Diskette Drive Diskette Drive Spare Part Number Information Diskette drive, 1.44 MB 176047-001 Diskette drive cable (spared in Cable Kit) 176004-001 1. Prepare the computer for disassembly (Section 5.3) and, in the order below, remove the following components: top cover (Section 5.10) hard drive (Section 5.11) RTC battery (Section 5.12) keyboard (Section 5.13) EMI shield (Section 5.14) TouchPad (Section 5.15) speakers (Section 5.16) display assembly (Section 5.17) speaker housing (Section 5.18) system board (Section 5.19)
Removal and Replacement Procedures5-39 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc 2. Lift the back edge of the diskette drive and swing it up and toward the front of the base assembly (Figure 5-34). Figure 5-34. Removing the Diskette Drive 3. Remove the diskette drive.
5-40Removal and Replacement Procedures COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc If necessary, remove the diskette drive cable by releasing the ZIF connector to which the cable is attached and disconnecting the cable (Figure 5-35). Figure 5-35. Disconnecting the Diskette Drive Cable
Removal and Replacement Procedures5-41 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 1:32 PM Part Number: 177845-001 File name: CH05.doc When installing the diskette drive, first insert the front of the drive through the opening in the base assembly , then lower the back edge of the drive into the base assembly . Make sure the FPC cable on the back of the drive fits inside the diskette drive shield (Figure 5-36). Figure 5-36. Installing the Diskette Drive
Connector Pin AssignmentsA-1 COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED Writer: David Calvert Saved by: JAbercrombie Saved date: 04/05/00 12:53 PM Pages: 8 Words: 693 Template: c:\msoffice emplates ef ef.dot Part Number: 177845-001 File name: Appa.doc appendix A CONNECTOR PIN ASSIGNMENTS Table A-1 RJ-11 Connector Pin Signal 6 5 4 3 2 1 7 8 1 2 3 4 5 6 7 8NC_J3A NC_J3B TIP RING NC_J3C NC_J3D Unused Unused Table A-2 Serial Connector 4 9 85 2 7 6 13 Pin Signal Pin Signal 1 Carrier Detect 6 Data Set Ready 2 Receive Data 7 Ready to Send 3 Transmit Data 8 Clear to Send 4 Data Terminal Ready 9 Ring Indicator 5 Ground