D-Link Router DHP-1565 User Manual

							116
D-Link DHP-1565 User Manual
Section 3 - Configuration
Network Name:
Public 
Network  Name:
Private 
Network  Name:
Scan:
Add Member:
Device Name: Password:
Member List: Link Rate:Status: You can set the name of your network and to make it either public 
or  private.  Make  sure  the  Network  Name  of  all  of  the  devices 
within your PowerLine network is the same.
Select  this  option  if  you  would  like  to  make  your  PowerLine 
network public with the default Network Name of “HomePlugAV”. 
Since  this  is  a  commonly  used  Network  Name,  it  is  less  secure 
than a private Network Name. 
Select this option if you wish to make your PowerLine network 
more secure by using a private Network Name. Type the name 
of your private PowerLine network in the field.
Scan for new PowerLine devices. 
This  section  lets  you  add  new  PowerLine  AV  devices  to  your 
PowerLine network. To add a new device, give it a Device Name 
and enter its Password, then click Add. When you add a device 
it is given the current Network Name.
Type a name you wish to use to identify a specific PowerLine AV 
device. For example, “Jack’s room”.
The Password is used to verify that you are authorized to perform changes on a device. You can find the Password printed on the 
back of your device.
This section provides information on the PowerLine AV devices in your PowerLine network, or any devices that were previously 
connected but it are currently disconnected.
Displays the device’s current data rate in Mbps. 
This field shows the status of the device. If the field displays the word Connect, then the device is connected to your PowerLine   
						

							117
D-Link DHP-1565 User Manual
Section 3 - Configuration
QoS Settings:Mac Address: network.  If  the  field  displays  the  word  Disconnect,  then 
the  device  has  been  added  to  the  network  but  it  is  not 
ready. Please check its password and make sure the device 
is powered on.
You  can  configure  your  PowerLine  AV  devices  to  give 
priority to the powerline network traffic accordingly. Enter 
the name, MAC Address, and priority level.
You can find the MAC address printed on the back of your 
device.   
						

							118
D-Link DHP-1565 User Manual
Section 3 - Configuration
Use MAC (Media Access Control) Filters to authorize wireless clients to access your network by their MAC addresses. When enabled, any client not 
on the MAC filter list will not be able to access your network.
MAC Address Filter:
MAC Address:
Wireless Client  List:
Save Settings: Select Enable or Disable from the drop-down
menu.
Enter the MAC address you would like to filter.
To find the MAC address on a computer, please refer 
to the Networking Basics section in this manual. Click 
Save Settings to activate and save.
Note:  Make  sure  to  enter  the  computer  you  are 
currently using to configure the access point first or 
you will not be able to access the configuration utility 
once you click Save Settings.
Select a DHCP client from the drop-down menu and 
click to copy the MAC Address. 
Click 
Save  Settings   to  save  and  activate  the  new 
changes.
Network Filter   
						

							119
D-Link DHP-1565 User Manual
Section 3 - Configuration
Advanced Wireless
Transmit 
Power:
WLAN 
Partition:
WMM Enable: Short GI: Sets the transmit power of the antennas.
Note:
  Transmit  power  is  regulated  by  international 
standard. Users are forbidden to change its maximum limit.
Select  this  checkbox  to  enable  WLAN  partition.  If  this 
feature  is  enabled,  then  there  is  no  barrier  between 
communication  among  wireless  stations  connecting  to 
the Access Point. If this is disabled, wireless clients are not 
allowed to exchange data through the Access Point.
WMM is a Quality of Service (QoS) system for your wireless network. Enabling this feature will improve the quality of video and ice 
applications for your wireless clients.
Check this box to reduce the guard interval time therefore increasing the data capacity. However, this setting less reliable and may 
create higher data loss.  
						

							120
D-Link DHP-1565 User Manual
Section 3 - Configuration
Wi-Fi Protect  Setup:
Reset to 
Unconfigure:
Current PIN:
Generate New PIN:
Reset PIN to  Default: Enables the Wi-Fi Protected Setup feature.
Restores the default Wi-Fi setup.
Shows  the  current  value  of  the  access 
point’s PIN.
Create  a  random  number  that  is  a  valid 
PIN. This becomes the access point’s PIN. 
You can then copy this PIN to the user
interface of the user.
Restores  the  default  PIN  of  the  access 
point.
Wi-Fi Protect Setup  
						

							121
D-Link DHP-1565 User Manual
Section 3 - Configuration
Add Wireless Device with WPS
Adding a Wireless Device Using the PIN Method
Please select one of the following configuration methods and click 
Next to continue. 
Click Add Wireless Device with WPS. 
If your wireless device supports WPS, select  Auto and click  Next to 
continue.   
						

							122
D-Link DHP-1565 User Manual
Section 3 - Configuration
Adding a Wireless Device Using the PBC Method
Select PBC to use Push Button Configuration in order to connect to 
your network.
Click Connect to continue.
Press the Common Connect  Button on the wireless device that you 
are adding to your network to complete the setup.  
						

							123
D-Link DHP-1565 User Manual
Section 3 - Configuration
Manually Add Wireless Device with WPS
If you would like to add a wireless device with WPS manually, select 
Manual and click Next to continue. 
Enter the following settings in the wireless device you are adding to 
your wireless network. Click Ok to continue.   
						

							124
D-Link DHP-1565 User Manual
Section 3 - Configuration
User Limit Settings
In this section, you may set a limit to the number of wireless clients to prevent heavy wireless traffic.  
						

							125
D-Link DHP-1565 User Manual
Section 3 - Configuration
Admin
This page will allow you to change the Administrator password. The administrator password has read/write access.
Enter  a  new  password  for  the  Admin  User 
Name. The administrator account can change 
the configuration of the device.
Enter  the  same  password  that  you  entered  in 
the  previous  textbox  in  order  to  confirm  its 
accuracy.
Enter DHP-1565.
Enables  a  challenge-response  test  which  will 
require users to type letters or numbers from 
a  distorted  image  displayed  on  the  screen 
to  prevent  online  hackers  and  unauthorized 
users  from  gaining  access  to  your  device’s 
configuration.  This  feature  is  disabled  by 
default.
Click Save Settings to save and activate the
new changes.
Password:
Verify
Password:
System Name: Enable
Graphical:
Save Settings: